waterpik ZZR-769M5E Hand Held ZZR Shower Head Instruction Manual

: June 10, 2024
: Waterpik

Table of Contents

TOOLS NEEDED
BEFORE INSTALLATION
COMPONENTS
INSTALLATION
OPERATION
CARE AND CLEANING
TROUBLESHOOTING GUIDE
LIFETIME LIMITED WARRANTY
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

waterpik ZZR-769M5E Hand Held ZZR Shower Head Instruction Manual

Thank you for purchasing this Waterpik® shower head. This booklet provides information to make installation easy and quick. You are minutes away from enjoying a powerful and invigorating shower experience with your new Waterpik® shower head. You can view more information about Waterpik® shower head products at www.waterpik.com. To learn more about Waterpik® water for wellness® benefits go to www.waterpikwellness.com.

TOOLS NEEDED

Gather the tools to install the shower head.

Adjustable Wrench or Pliers (not included)

BEFORE INSTALLATION

Remove old shower head and all pipe tape from shower pipe.
Pipe tape is not required for installation of this shower head.
Ensure that washer from old shower is not remaining in shower pipe. Use a thin utensil such as a pencil or screwdriver, to check inside shower pipe for old washers. Do not use your fingers.

COMPONENTS

Instructions

INSTALLATION

Tighten pivot ball to shower pipe. Ensure large nut is secure by hand tightening.
Connect the ridged connector to the bracket and hand tighten.
Connect the other end with the rubber ring to the hand held shower head and hand tighten.
Place hand held shower head in bracket.

OPERATION

Spray Selector:
Allows you to select from various spray settings. To choose spray setting, rotate lever at base of shower face left or right.

Hybrid Power Control:
The Easy Pause function is perfect for conserving water while you lather, shave, or shampoo. It is also super convenient to adjust spray strength in any setting. To operate, move the switch all the way to the right for a Pause (trickle) and all the way to the left for Full Flow. The spray strength of any setting can be adjusted by moving the switch somewhere in the middle.
Hybrid Power Control

Vacuum Breaker Backflow Prevention
Note: Several U.S. state and local municipal plumbing codes require the use of a backflow prevention device when installing a hand shower. This device is termed a vacuum breaker. If your hand shower includes a vacuum breaker it will be located in the hose, and the hose end with the vacuum breaker will include a sticker that reads “attach this vacuum breaker end to shower bracket.” If the hose is not installed in this manner, water will not flow. If your hand shower does not include a vacuum breaker, and you would like to obtain one free of charge, please contact us at 1-800-525-2774 (U.S. calls only) and request part number 20009558.

WARNINGS:

To avoid hot water dangers and conserve even more energy, make sure your water heater is set at 48.9°C /120°F or below.
Test the tub/shower water with your hand before bathing.
For additional safety for Ecoflow® or high efficiency shower heads, it is recommended that all homes have installed a pressure balance tub and shower valve with the rotational limit stops properly set by a plumber. If you are unsure of your valve type consult your plumber.
Always ensure the hand held shower head is properly placed in the bracket, so as to prevent the shower head from falling.
Do not pull on or tug the flexible hose. This may result in the shower head coming loose and falling.
For external use only. The potentially deadly amoeba, Naegleria fowleri, may be present in some tap water or unchlorinated well water.

CARE AND CLEANING

To maintain proper working conditions cleaning is required when mineral deposits appear on spray orifices. To clean mineral deposits, gently rub rubber nozzles on face of shower head to dislodge.
To clean heavier deposits, remove shower head and soak face down in 1-2 cups of white vinegar (use white vinegar only) for 2-3 hours. Replace shower head and run in each spray setting toflush out vinegar.
Do not clean or rinse any part with harsh chemicals, heavy duty cleaners, or abrasives; this may damage parts or finish and voids warranty.
Clean filter screen in the bracket by unscrewing filter from the pivot ball. Rinse by back flushing to remove particles. Re-install filter screen and follow steps 1-7 under installation to re-install shower head.

TROUBLESHOOTING GUIDE

Problem	Solution

No water flow from
shower head| a Confirm previous shower washer is not in
shower pipe.
b Confirm there is only one washer in
connection.
c Check both hose ends to clear any blockage
Leaking at the pipe
connection| a Confirm only one washer in connection with
shower pipe.
b Grate bar of soap across shower pipe
threads to act as a sealant.
Leaking from hose
connection| a Check hose ends to make sure washers are
present.
Low water pressure or
missing spray patterns| a Make sure Hybrid Power control is not in
trickle position.
b Clean filter screen (located in pivot ball).
c Clean shower head in vinegar/water solution.
(See care & cleaning section).

LIFETIME LIMITED WARRANTY

Save your receipt as proof of purchase is required for warranty action.
Water Pik, Inc. warrants to the original purchaser of this product that it is free from defects in material and workmanship for as long as the original purchaser owns this product. Water Pik, Inc. will replace the product, which in our opinion is defective, provided that the product has not been abused, misused, altered or damaged after purchase. This includes damage due to use of tools or harsh chemicals. In the event an item has been discontinued, Water Pik, Inc. will replace with what it deems to be the closest product. Water Pik, Inc. is not responsible for labor charges, installation, or other consequential cost. The responsibility of Water Pik, Inc. shall not exceed the original purchase price of the product. This warranty gives you specific legal rights. You may also have other rights that vary depending on where you reside. Water Pik disclaims all other express or implied warranties to the extent permitted by law including, but not limited to, all warranties of merchantability and fitness for a particular purpose. All implied warranties are limited to the duration of this limited warranty. Some states or provinces may not allow limitation on how long an implied warranty lasts, so above may not apply to you.

Limitation of Liability: This limited warranty is your sole remedy against Water Pik and it shall not be liable for any damages, whether direct, indirect, incidental, special, consequential, exemplary or otherwise, including but not limited to property damage, arising out of any theory of recovery, including statutory, contract or tort.

BINDING ARBITRATION AND WAIVER OF RIGHT TO ASSERT MATTERS IN COURT AND RIGHT TO JURY TRIAL
By purchasing, installing, or using this product you agree that any controversy or claim arising out of or relating to your purchase, use, modification, installation, or removal of this product shall be settled by binding arbitration. The arbitrator’s decision will be final and binding. Judgment on the award rendered by the arbitrator may be entered in any court having jurisdiction over the matter. Further, you agree that you will not have the right to litigate any claim arising out of or in relation to your purchase, use, modification, installation, or removal of this product in any court or to have a jury trial on that claim. Arbitration of any matters shall be administered by the American Arbitration Association and conducted by one arbitrator in accordance with the consumer arbitration rules of the American Arbitration Association in effect at the time of filing of the demand. The venue for all such arbitrations shall be Colorado and any such arbitration shall be subject to the Federal Arbitration Act and Colorado law.

WAIVER OF RIGHT TO PARTICIPATE IN CLASS ACTIONS OR PURSUE
CLAIMS IN A REPRESENTATIVE CAPACITY.
Further, by purchasing, installing, or using this product you agree that arbitration must be on an individual basis. This means neither you, nor we, may join or consolidate claims in arbitration by or against other purchasers or users of Waterpik® products or the general public. Additionally, you may not litigate in court or arbitrate any claims as a representative or member of a class or in a purported representative capacity on behalf of the general public, other purchasers or users of this product, other persons or entities similarly situated, or in a private attorney general capacity.
If product malfunctions or becomes damaged, stop use immediately and contact Water Pik, Inc. for assistance.

Have any questions or need assistance?

For quick service prior to calling have your model number and receipt ready.
In the U.S., call our toll-free
Customer Assistance Line
1-800-525-2774, Monday –
Friday, 7:00 AM – 5:00 PM MST.
English only.
or visit www.waterpik.com
In Canada, call our bilingual
toll-free Customer Assistance
Line 1-888-226-3042, Monday –
Friday, 7:00 AM – 5:00 PM MST.
or visit www.waterpik.ca