LEMAX 05698 Thicket Falls Cabin Instruction Manual

05698 Thicket Falls Cabin
Instruction Manual

05698 Thicket Falls Cabin

THICKET FALLS CABIN, WITH 4.5 V ADAPTOR

• THIS PRODUCT IS USED AS CHRISTMAS DECORATION, NOT A HUMIDIFIER.
• THIS IS NOT A TOY. THEREFORE NOT SUITABLE FOR CHILDREN. KEEP OUT OF REACH OF CHILDREN.
• WARNING ! NOT SUITABLE FOR CHILDREN UNDER 36 MONTHS DUE TO SMALL REMOVABLE PARTS.
• THE EXTERNAL FLEXIBLE CABLE OR CORD OF THIS LUMINAIRE CANNOT BE REPLACED, IF THE CORD IS DAMAGED, THE LUMINAIRE SHALL BE DESTROYED.
• RATED VOLTAGE: 4.5 V
• LED: 3 V, 0.020 A
• LED IS NON-REPLACEABLE
•  FOR INDOOR USE ONLY.

CONTENTS :
This operation manual is compatible with other smoking products. The appearance of accessories varies depending on the design but they are of same functions.
Building x 1
A. Smoke Function Mechanism x 1
B. Wick – inside the chimney x 1
C. Spring – inside the chimney x 1
D. Roof Cover x 1
E. Inner Lid x 1
F. Adaptor x 1
G. Replacement Wick (Length: 190mm) x 2

OPERATING INSTRUCTIONS

1. Setting up the product
   • Place the unit on flat, level surface.
   • Take away the adhesive tape on the chimney (Dia.1).
   • Ensure Smoke On/Off button on right side of the unit in off position “O” (Dia. 2).
   • Insert the jack of the adaptor (F) into the reception socket at the back of the unit (Dia.
   3). Plug the adaptor into a household electrical outlet.
   • This power unit is intended to be correctly orientated in a vertical or floor mount position.
   Please note!
   Suggest using the adaptor provided.
   

2. Filling the water tank with water
   • Remove the roof cover (D) and the inner lid (E) from the unit (Dia. 4).
   • Fill the water tank with approximate 650 mL (21.98 fl.oz.) water to the puffy mark(Dia. 5).
   • Put the inner lid and then the roof cover back onto the unit.
   Important!
   ▶ Water level should not exceed the puffy mark.
   ▶ Use clean room-temperature tap water.
   

3. Turning on the product
   • Locate Power Cord extending from rear of the unit and shift the button to on position “-” (Dia. 6).
   • When activated, lights will illuminate the unit.

4. Turning on and turning off smoke
   • Ensure Power Cord extending from rear of the unit in on position “-” (Dia. 6).
   • Shift Smoke On/Off button to on position “-” (Dia. 7) to activate the smoke function.
   • Wait about 2 minutes for water absorption by the wick (B). “Smoke” will come out through the chimney.
   • Shift Smoke On/Off button to off position “O” (Dia. 8), smoke will stop.
   

5. Refilling the water tank
   • When water inside the water tank runs out to lower level, there is no smoke and a red light will flash (Dia. 9).
   • Shift Smoke On/Off button to off position “O” (Dia. 8), the red light will go off .
   • Refill the water tank with water by repeating Point (2).
   • Shift Smoke On/Off button to on position “-” (Dia. 7) to activate the smoke function again. Smoke will start again.

6. Replacing the wick
   • When the wick (B) deteriorates, gets dirt, smoke will go less. Replace it with the replacement wick (G) provided.
   • Remove Smoke Function Mechanism (A).
   • Take out the wick from the chimney.
   • Insert the replacement wick into the chimney gently and carefully.
   • Cover the replacement wick with Smoke Function Mechanism (Dia. 10).
   • Wait about 2 minutes for water absorption by the replacement wick.
   Important!
   ▶ When taking out the wick, and if the supporting spring (C) comes out together, put the spring back into the chimney.
   ▶ Dock Smoke Function Mechanism on to the chimney so that the jut matches the small round notched (Dia. 11) correctly.
   ▶ Ensure top part of the wick goes upright into Smoke Function Mechanism.
   

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>