FRANKE Cooker Hood Tender 725 Instruction Manual
- June 10, 2024
- Franke
Table of Contents
FRANKE Cooker Hood Tender 725
SAFETY INSTRUCTIONS
Please read this installation and user guide carefully before installing and
using the product, paying special attention to the safety instructions.
Keep the instructions for reference or for the next owner.
Disconnect the product from the power supply prior to cleaning or maintenance.
- Diversion of exhaust air must be carried out in accordance with instructions issued by the appropriate authority.
- Exhaust air may not be directed into flues that are used for fumes from items such as gas, wood or oil-burning stoves or fireplaces.
- The distance between the stove and the product must be at least 50cm. For gas hobs, the distance should be increased to 65 cm. Adjust accordingly if the stove manufacturer recommends a higher mounting height.
- For safety reasons, installation and replacement of cables or other types of connectors should only be carried out by a qualified professional.
- You must not flambé food underneath the product.
- If the product is to be used at the same time as products that use energy sources other than electricity, i.e., gas hobs, gas, wood or oil-burning stoves or fireplaces, etc, the room must have an adequate supply of air.
- The product may be used by children from 8 years of age and persons with mental, sensory or physical impairment, or a lack of experience and knowledge, provided they are given information about how the product is to be used.
- Children should not be allowed to play with the product. Children must not undertake cleaning or maintenance of the product unsupervised.
- Accessible parts of the product may become hot when food is being prepared.
- A fire is more likely to spread if the product is not cleaned as frequently as indicated.
INSTALLATION
Cooker hood for wall mounting. The cooker hood is equipped with Easy Clean
motor package HE (High Efficiency), LED lighting and a metal mesh filter. The
cooker hood has four speeds and a timed ventilation mode. Installation, use,
care, maintenance etc., are described in these instructions.
TECHNICAL INFORMATION
| Measurements | see Fig. 1 |
|---|---|
| Electrical installation | 230 V ~ earthed |
| Lighting | LED 2 x 2 W |
INSTALLATION
Fixing parts, screws for mounting, etc. are supplied with the cooker hood.
Electrical installation
The cooker hood is supplied with a cable and earthed plug for connection to an earthed socket. The socket should be accessible after installation is complete.
Installation Components
| D | 2 pcs | Brackets for the upper chimney |
|---|---|---|
| E | 7 pcs | Wall plugs |
| F | 7 pcs | Screws 4,5 x 39 TORX T25 |
| G | 2 pcs | Screws 2,9 x 9,5 TORX T10 |
| H | 1 pcs | Cold breed protection |
| I | 1 pcs | Ventilation tape |
Installation of wall mounts, marking the wall
Attention!
For total height, the distance between the bottom of the cooker hood and the
top of the chimney, see measurements Fig. 1. When installing with an extended
upper chimney section or if the cooker hood will be fitted with a carbon
filter kit, refer to the separate instructions and measurements.
Mark a centre line A above the stove where the cooker hood is to be installed.
Draw a horizontal reference line B, above the stove, Fig. 2.
Place the upper bracket D for the chimney on the wall, as shown in Fig. 2.
Mark the bracket’s screw holes on the wall. Place the lower bracket D for the
chimney on the wall, as shown in Fig. 2, below the upper bracket, and mark
where the screw holes should go on the wall.
Mark the screw holes for the mounting of the cooker hood, C, on the wall, as
shown in Fig. 2.
Drill Ø 3,5 mm holes in the centre of all the marked points.
Fasten the consoles to the chimney using the screws F.
If the supplied plugs are to be used, drill Ø 5,5 mm holes. Drill the hole Ø 5
mm deeper than the length of the plug. Place wall plugs E in the holes. Check
that the screws and plugs used are intended for the wall material (red plastic
plug is for attachment in concrete, brick and natural stone).
Assembly
Remove grease filter and motor unit, see Fig. 8 and Fig. 9.
Prior to mounting, screw two screws F into the pre-drilled holes, Fig. 3.
Hang the cooker hood and adjust it horizontally Secure it in place with a
screw F.
Reinstall the motor unit and grease filter.
Tape the downdraught damper I into position using tape I, Fig. 4.
If the connection is Ø 125 mm, a reducing coupling sleeve must be used. Secure
the reducer to the downdraught damper with tape I.
Connection to exhaust flue
Connect the cooker hood with a pipe or tubing Ø160 mm.
Attention!
When using connecting tubing, the tubing must be stretched and installed
directly adjacent to the connection, Fig. 5.
Mounting the chimney
Chimney upper section
Gently bend the two sides of the upper chimney section outwards and hook them
on the brackets D. Make sure they are secure.
Attach the sides to the upper brackets using screws G (2.9 x 9.5 mm), Fig. 6.
Chimney, lower section
Gently bend the two sides of the lower chimney section outwards and lower it
on to the hood. Hook the bottom of the chimney section into place. Make sure
they are properly in position.
Removal of protective plastic
Remove all protective plastic from the filter and any other parts of the
product.
INSTRUCTIONS FOR USE
FUNCTION SWITCH
A. Lighting.
B. Ventilation mode. The extractor fan runs at low speed for 60 minutes.
C. Speed 1 on fan motor.
D. Speed 2 on fan motor.
E. Speed 3 on fan motor. If the button is held down for 2 seconds, the fan
goes into intensive mode. After 7 minutes, the fan motor returns to the
previously set position. The fan can be started and stopped with the B-E
buttons.
It is a good idea to turn on the hood before starting to cook, as this
prevents cooking smells spreading into the room. Adjust the speed of the hood
depending on the type of food you are preparing. If possible, allow the hood
to run at a low speed for a few minutes after you’ve finished cooking. You may
also wish to run the hood on the low setting when the oven is in use or after
using the dishwasher.
CARE AND MAINTENANCE
Cleaning
The cooker hood should be cleaned with a damp cloth and washing-up liquid. The
filter must be cleaned twice a month, with normal usage.
Remove the grease filter by opening the snap, Fig. 8. Handle the filter
gently, be careful not to bend them. Soak the filter in a solution of warm
water and washing-up liquid. The filter can also be washed in a dishwasher.
Refit the grease filter after cleaning, make sure they snap firmly into place.
Motor core and hood interior must be cleaned at least twice a year.
The motor core is removed by first disconnecting the contact on the side of
the motor unit, Fig. 9A. Rotate the latches, Fig. 9B, that lock the motor core
in place. Pull the unit outwards so that it is freed from the pins, and then
downwards.
Attention!
The motor core should not be washed or exposed to moisture! The cooker hood
should be cleaned with a slightly damp cloth and washing-up liquid.
One side grille is detached by lifting up the stop lug with a screwdriver and rotating the grill in the direction of FREE, Fig. 10.
REPLACEMENT OF LED LIGHTING AND LED DRIVER
Attention!
The replacement of the LED lighting and LED driver must be carried out by an
authorised professional. Contact the service organisation.
If the lighting and driver are damaged, they must be replaced with an equivalent special light fixture and driver from the manufacturer or its service agent.
SERVICE AND WARRANTY
Check that the fuse is intact. Go through all
the functions to check what is not working.
Contact Franke Service
Tel. +46 (0)912-40 500
www.franke.se/service
They can help you fix the problem or refer you to the nearest service agent
for fast and effective service.
The product is covered by the relevant EHL provisions.
PACKAGING AND PRODUCT RECYCLING
The packaging should be deposited at your nearest recycling point.
The symbol means that the product must not be treated as household waste. It should instead be taken to a collection point for the recycling of electrical and electronic components. By ensuring that the product is dealt with in the correct manner, you are helping to prevent the adverse environmental and health effects that could arise if the product was disposed of as regular waste. For further information on recycling, contact your local authority or waste disposal service, or the store where you purchased your product.
ECO–DESIGN DIRECTIVE
The product meets and is tested in accordance with the eco-design requirements of European Regulation 66/2014.
Documents / Resources
|
FRANKE Cooker Hood Tender
725
[pdf] Instruction Manual
Tender 725-12, Tender 725, Cooker Hood Tender 725, Cooker Hood, Tender 725
Hood, Hood
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>