FOREVER Hot Stamping Foils Instruction Manual
- June 10, 2024
- FOREVER
Table of Contents
FOREVER Hot Stamping Foils
Product Information
- The product is designed for finishing with hot stamping foils.
- The transfer instructions are only applicable for Laser-Dark (No-Cut) A-Foil & OKI White Toner Printers.
- The transfer settings involve B-Paper to A-Foil transfer to textile hot stamping foil.
- The recommended pressure ranges from 2-3 Bar / 29-43.5 psi (medium pressure) to 5 Bar / 72.5 psi (high pressure).
Product Usage Instructions:
- Prepare the B-Paper and A-Foil for transfer.
- Place the B-Paper on top of the A-Foil, ensuring that the shiny side of the A-Foil is facing up.
- Transfer the B-Paper to the A-Foil using a heat press with medium pressure (2-3 Bar / 29-43.5 psi) for 90 seconds.
- Peel off the B-Paper from the A-Foil after the transfer is complete.
- Place the A-Foil onto the textile and transfer using a heat press with low pressure (2 Bar / 29 psi) for 5-10 seconds.
- Peel off the A-Foil from the textile after the transfer is complete.
- Place the hot stamping foil onto the transferred design and apply heavy pressure (5 Bar / 72.5 psi) for 30-45 seconds using a swing-away or pneumatic press.
- Peel off the hot stamping foil from the design to finish.
Note:
- For the best results, it is important to use heavy pressure when finishing with hot stamping foils.
- The 4-Color-Black consists of 100% Cyan, 100% Magenta & 100% Yellow.
For further information or support, please visit www.amayauk.com or contact customer support at 02392 590 281 or [email protected].
Transfer Instructions for:
FINISHING with Hot Stamping Foils ONLY FOR LASER-DARK (NO-CUT ) A-FOIL & OKI
WHITE TONER PRINTERS
TRANSFER SETTINGS
°C °F ****
B-PAPER TO A-FOIL| 155°C / 310°F| 90 sec.| 2 – 3 Bar /
29 – 43.5 psi / medium pressure
TRANSFER TO TEXTILE| 155°C / 310°F| 5 – 10 sec.| 2 Bar / 29
psi / low pressure
HOT STAMPING FOIL| 155°C / 310°F| 30 – 45 sec.|
5 Bar / 72.5 psi / high pressure
FINISHING WITH HOT STAMPING FOILS
PREPARATION OF THE TRANSFER
- Print your design using CMYK BLACK(4-C olor-Black*) & Press with B-Paper (See Table above).
- Separate the B-Paper from the A-Foil while HOT, in a Slow, Low & Fluid Motion.
- Cut around your transfer to remove the coating frame.
TRANSFER TO TEXTILE
- Place the transfer on your textile & press together (See Table above).
- Wait until the textile has completely cooled down, BEFORE removing the A-Foil!
APPLYING THE HOT STAMPING FOIL
- Place the desired sheet of Hot Stamping Foil on your design, cover it with a sheet of Matt Finish Economy & press together (See Table above).
- Wait until the Hot Stamping Foil has completely cooled down, BEFORE removing.
- Wash resistant up to 40°C (Cold Wash Cycle).
TIP: Use a textile to rub over the finished design to remove left-over
HSF particles!
4-Color-Black consists of 100% Cyan, 100% Magenta & 100% Yellow!
ATTENTION: We recommend Swing-way and Pneumatic Presses! It is important
to use heavy pressure for the best results.
- www.amayauk.com
- 02392 590 281
- [email protected]
Southern Office: 400-450 Nest Business Park, Martin Road, Havant,
Hampshire, PO9 5TL
Midlands Office: Unit 4A-C East Bridgford Business Park, Kneeton Road,
East Bridgford, Nottingham, NG13 8PJ