Tuya Zigbee Motor with Built-in Li-ion Battery USB Charging User Manual

Zig bee Motor with Built-in Li-ion Battery
USB Charging User Manual

Product Info

Models & Parameters (for details about other parameters, see the product nameplate)

Caution

1. This product is for indoor use only, do not use outdoor or in humid environments.
2. This motor has a built-in rechargeable Li-ion battery pack with integrated charge management. Max input voltage: 5V/2A.
3. Please charge it before using for the first time, make sure it is fully charged before first use
4. When the battery voltage is low, LED will flicker 8 times to give a low-voltage alarm when motor starts.
5. The motor will jog in operation, please do not proceed to the next step until it complete.
6. During operation, the effective interval of the transmitter button operation is 10 seconds. If there is no effective transmitter operation for more than 10 seconds, it will  automatically exit the current mode.
7. The motor can be paired with max 10 controllers.
8. Please do not use motor when charging.
9. Upper & Lower limits cannot be set at the same position, limits saved even power off.
10. The motor runs constantly for at 6 mins max without any other operation.
11. Do not lift the motor by grabbing the wire or antenna.

Instructions

Motor head butte functiotor head button (H) functions

sleep mode
Adding/Removing Controller| Hold for 2s| Jog1| Flicker1| Operation needs be done within 10s
Zigbee Connecting| Hold for 6s| Jog2| Flicker2| Entering Zigbee connectionmode
Direction Reverse| Hold for lOs| Jog3| Flicker3| All settings saved after direction reversed
Reset| Hold for 16s| Jog4| Flicker4| All settings deleted

a. Pairing Motor with Controller
Way1: Power on, add a new controller

Way 2: Power nomad controller B via pre-existing controller A

Note: Pairing can not be done under group channel or 0 channel.

b. Direction Reverse
Correct

If the limits are not set, and direction goes opposite.

If limits are set and direction goes opposite.

Note: Do reverse the direction when it goes opposite.

c. Upper & Lower Limits Setting

Note: Upper & Lower limits cannot be set at the same point.
Before limits set, the motor will run in one-touch mode by pressing Up or Down, hold Up or Down for 2s, motor runs in constant-touch mode.
Once limits set, pass Up or Down, motor runs in constant-touch mode.

d. One-touch/Constant-to Mode

Same operation can toggle from one-touch to constant -touch mode.
Note: When motor in one-touch mode, hold Up or Down for more than 2s, it will run in constant-touch mode.

e. Setting and Cancelling Favorite Position
Setting

f. Hot key to the Fav. Position

Fav
Note: The Fav. position setting only can be done after upper & lower limits set.

g. Adjusting Upper & Lower Limits
Adjust Upper limit

Adjust Lower limit

Note: The operation should be done within 4mins.

h. Adjusting Motor Speed

Note: If motor doesn’t jog, the max/min speed has already been reached.
There are 3 speeds adjustable.

i. Removing Controllers
Remove a single controller

Remove controller B via pre-existing controller A

Remove all controllers:

Note: All the settings are saved even controllers removed(limits set are saved).
Controller A/B are already paired to motor.

j. Cancelling Limits

Note: It is forbidden to run the motor if installed into the shade without limits.
Limits should be set immediately to protect the shade.

k. ZigBee Connecting
Sighed Connecting
“Connection requirement
a. Make sure the phone is connected to the Wi-Fi network.

Download App
a. Search for “Smart Life” In the app store or scan the QR code

https://smartapp.tuya.com/smartlife

b. The Tuya ZigBee gateway device need to be added to the “Smart Life” APP first, please refer to its manual for details.

2: Add Device
a. Make sure the phone is connected to the Wi-Fi network
b. Make sure the Tuya ZigBee gateway device is connected to “Smart Life” App
c. Make the motor is ready to be connected to ZigBee by following steps:

d. Find the added Tuya Zigboe gateway on the “Smart Life” App, click “+° to add a sub-device, and then click “LED already blink”, the APP will automatically search for motor device.

e. After adding successfully, click to modify the device name.

f. After the motor device is added success fully, the LED on motor head will be on for 10s and then go off.

g. Now the motor can be controlled by App from anywhere, anytime

Troubleshooting

2.Motor inactive
3.Low battery| 1.Add controller
2.Hold H button for 2s to activate motor
3.Charging
Motor stops suddenly| 1.Upper & Lower limit set incorrectly
2.Shade exceed rated load 3.Low battery| 1.Re-set Upper & Lower limits
2.Adjust load
3.Charging
LED flickers 8 times on motor head when motor starts| Low battery| Charging

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>