SQUARE D Homeline Circuit Breaker Instruction Manual

: June 10, 2024
: SQUARE D

Table of Contents

SQUARE D Homeline Circuit Breaker
Product Information
Product Usage Instructions
Introduction
Single-Row Bus Construction
- HAZARD OF EQUIPMENT DAMAGE
Remove Cover Twistouts
Prepare for Installation
Read User Manual Online (PDF format)
Download This Manual (PDF format)

SQUARE D Homeline Circuit Breaker

Product Information

Service Entrance Devices

The Homeline Combination Service Entrance Devices are designed to restrict the installation of more overcurrent devices than is designed for. The plug-on connection arrangement for the HOMT circuit breakers is different from HOM circuit breakers. The tandem circuit breaker type HOMT may only be installed in combination service entrance devices where the bus bar connector has a configuration as in Figure 3. The circuit breaker comes in three variants: HOM one-pole, HOM two-pole, and HOMT Tandem. The product dimensions are 0.99 inches (25 mm) in width, 1.73 inches (44 mm) in height, and 1.86 inches (47 mm) in length.

Product Usage Instructions

Remove knockouts from the Homeline Combination Service Entrance Devices. Appropriate to knockout pattern, drive center knockout inward or outward. Alternately pry up or drive in outer rings one at a time to the opening required.
For double-row bus construction, the tandem circuit breaker type HOMT may be installed where the bus bar connector has a slot at the centerline of the desired pole space. Do not use excessive force to install a HOMT tandem circuit breaker where no connector slot is provided as it can result in damage to the circuit breaker case.
For single-row bus construction, the tandem circuit breaker type HOMT may only be installed in combination service entrance devices where the bus bar connector has a configuration as in Figure 3. Failure to follow this instruction can result in equipment damage.
Tighten all electrical connections to specifications. See the lug torque data chart on the combination service entrance device wiring diagram for torque specifications. See circuit breaker marking for lug torque specifications.
Remove cover twist outs by twisting out with pliers at the center of twist out for a one-pole branch circuit breaker opening.

Introduction

HomelineTM Combination Service Entrance Devices are designed to restrict the installation of more overcurrent devices than the number for which it was designed. Be advised that the plug-on connection arrangement for HOMT circuit breakers is different from HOM circuit breakers.

DANGER
HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH

Apply appropriate personal protective equipment (PPE) and follow safe electrical work practices. See NFPA 70E, CSA Z462 or NOM-029-STPS.
This equipment must only be installed and serviced by qualified electrical personnel.
Turn off all power supplying this equipment before working on or inside equipment.
Always use a properly rated voltage sensing device to confirm power is off.
Replace all devices, doors, and covers before turning on the power to this equipment. Failure to follow these instructions will result in death or serious injury.

Double Row Bus Construction
Tandem circuit breaker type HOMT may be installed in combination service entrance devices where the bus bar connector has a slot at the centerline of the desired pole space. See Figure 1.

NOTICE: HAZARD OF EQUIPMENT DAMAGE Do not use excessive force to install a HOMT tandem circuit breaker where no connector slot is provided. See Figure

Failure to follow this instruction can result in damage to the circuit breaker case.

Note: Tighten all electrical connections to specifications. See lug torque data chart on combination service entrance device wiring diagram for torque specifications. See circuit breaker marking for lug torque specifications.

Single-Row Bus Construction

CAUTION

HAZARD OF EQUIPMENT DAMAGE

Tandem circuit breaker type HOMT may only be installed in combination service entrance devices where the bus bar connector has a configuration as in Figure 3. Failure to follow this instruction can result in equipment damage. SQUARE-D-Homeline-Circuit-Breaker-fig-2

Note: Tighten all electrical connections to specifications. See the lug torque data chart on the combination service entrance devise wiring diagram for torque specifications. See circuit breaker marking for lug torque specifications. SQUARE-D-Homeline-Circuit-Breaker-fig-3

Remove Cover Twistouts

Remove only those twist outs which match installed circuit breakers by twisting out with pliers at the center of twist out.
Close unused circuit breaker openings with filler plates.
Order catalog number HOMFP for filler plates. Each filler plate closes a one-pole branch circuit breaker opening.
Figure 7: Remove Cover Twistouts

Prepare for Installation

Remove knockouts. Appropriate to the knockout pattern, drive center knockout inward or outward. Alternately pry up or drive in outer rings one at a time to the opening required.
Figure 8: Remove Knockouts
Select the proper cable clamp, or use other approved methods for securing the cable or conduit to the enclosure.
Install and wire branch circuit breakers.

CAUTION
HAZARD OF EQUIPMENT DAMAGE Use only HomelineTM circuit breakers and replacement parts with this product. Use of other components voids the warranty, may void the UL listing and may result in personal injury or equipment damage. Refer to device markings for specific restrictions. Failure to follow this instruction can result in personal injury or equipment damage.

Circuit Breaker Installation

Turn off circuit breaker.
Insert wire terminal end of circuit breaker into mounting hook.
Push circuit breaker inward until plug-on jaws plug securely on to bus bar connector.
Install wires.

Identify Circuits
Identify branch circuits on directory label or directory stickers.
Energize the Circuit
Note: Before energizing combination service entrance devices, turn main and branch circuit breakers to the OFF position.

Turned on power to the combination service entrance device.
Turn main circuit breaker ON.
Turn on branch circuit breakers.

Handle at mid position indicates the circuit breaker is tripped. To reset, move handle to the off position and then to the on position.
Figure 9: Energize the Circuit

Removal of Circuit Breakers

Turn circuit breakers OFF.
Remove wires.
Disconnect plug-on jaws from bus bar connection by pulling circuit breaker outward until it disengages from mounting hook.

Electrical equipment should be installed, operated, serviced, and maintained only by qualified personnel. No responsibility is assumed by Schneider Electric for any consequences arising out of the use of this material. Schneider Electric and Square D are trademarks owned by Schneider Electric Industries SAS or its affiliated companies. All other trademarks are the property of their respective owners.

Circuit Breaker Installation for HomelineTM Combination Service Entrance Devices Instruction Bulletin