IPVIDEO HALO-2C HALO Smart Sensor User Guide
- June 10, 2024
- IPVIDEO
Table of Contents
IPVIDEO HALO-2C HALO Smart Sensor
HALO-2C DEMO UPGRADE TO 3C GUIDE
Brought to you by: IPVideo Corporation
Product Information
The HALO-2C is a video management software system designed for use with IP cameras. The software allows for the management and recording of video footage from multiple cameras, as well as advanced features such as motion detection and remote viewing.
Product Preparation
Before upgrading to the HALO-3C software, ensure that you have the necessary hardware and software requirements. These include:
- A computer with at least 4GB of RAM and a dual-core processor
- Windows 7 or higher operating system
- The HALO-2C software is installed and running correctly
- A USB drive with at least 1GB of free space
Usage Instructions
- Download the HALO-3C software upgrade from the IPVideo Corporation website.
- Save the upgrade file to the USB drive.
- Insert the USB drive into the computer running the HALO-2C software.
- Open the HALO-2C software and navigate to the “Upgrade” section.
- Select “Upgrade from USB” and follow the on-screen instructions to complete the upgrade process.
- Once the upgrade is complete, restart the HALO-2C software to begin using the HALO-3C features.
For further assistance or technical support, please contact IPVideo Corporation at info@ipvideocorp.com or call 631.969.2601.
BEFORE YOU START
INCLUDED PARTS
- HALO-3C
- Mounting Ring
- Protective Pouch for HALO
- PANIC Button
- 1ft Ethernet Cable
- 4x Mounting Screw
- 4x Locknut
TOOL REQUIREMENTS
-
2 Phillips Screwdriver
- T10 Security Torx Wrench (included)
- 8 mm Wrench
PREPARATION
- Begin by removing the existing HALO-2C from the acrylic case.
- There are 2 mounting wings that can be accessed by reaching within the Acrylic and pushing into the “Closed” position allowing the user to remove the HALO-2C.
- Unplug the ethernet cable from the HALO-2C.
- Remove the existing 6” ethernet cable from the PoE injector inside the acrylic case.
- Replace this cable with the included 1ft Ethernet cable.
- Once this cable has been replaced, proceed to the installation process.
INSTALLATION
- From inside the bottom opening of the acrylic case, place the provided mounting ring inside the existing 5” cutout.
- Inside the box of the HALO-3C, there is a mounting plate. Place this mounting plate on top of the mounting ring. Users will find that the hole pattern on both pieces aligns.
- If the holes do not align, rotate the mounting ring until all 4 mounting holes line up.
- Using the included mounting screws, place all 4 through the aligned holes.
- From inside the acrylic case, use the included locknuts and hand-tighten each mounting screw. This will allow the mounting ring to rotate into the correct position before locking it into place.
- Spin the mounting plate so that the center line seen below is perpendicular to the bottom of the acrylic case.
- Using an 8 mm wrench and Phillips screwdriver, tighten the nuts so the mounting plate can no longer rotate.
- **NOTE*** over tightening may affect mounting functionality
- From inside the bottom opening of the acrylic case, feed the 1ft ethernet cable through the hole in the center of the mounting ring.
- Plug the ethernet cable into the HALO-3C. Ensure the ethernet cable goes into the “IN” port on the HALO-3C.
- Place the HALO-3C onto the mounting plate and rotate it into place.
- Users can use the included protective pouch when HALO-3C does not need to be attached to an acrylic case.
- The protective pouch will fit into the acrylic case for storage.
1490 North Clinton Ave, Bay Shore NY 11706 | ipvideocorp.com | info@ipvideocorp.com | 631.969.2601.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>