ibb testing VTC8920B Power Supply Unit User Manual

: June 10, 2024
: ibb testing

Table of Contents

ibb testing VTC8920B Power Supply Unit
Product Information
Safety Instructions
Usage Instructions
GENERAL INFORMATION
Support
Usage
Connectors
Accessories
Technical Data
Maintenance, Repair and Disposal
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

ibb testing VTC8920B Power Supply Unit

Product Information

VTC8920B Power Supply Unit
The VTC8920B Power Supply Unit is a module that operates with line voltage. It comes with a user manual that is available for download in different languages from the manufacturer’s website. The module has connectors and accessories that allow for easy usage and maintenance. It has technical data that includes its dimensions, weight, and power consumption. The module can be used in different applications and environments.

Safety Instructions

Before putting the device into operation, please observe the safety instructions on the module and read the safety instructions as well as the user manual. Failure to do so may result in personal injury or damage to the module.

Usage Instructions

Connect the module to a power source using the IEC 60320 C13 connector.
Ensure that the power source matches the voltage requirement of the module (120 V).
The module can be mounted on a 4U 19-inch rack using appropriate accessories.
Refer to the user manual for more information on usage, maintenance, repair, and disposal.

The User Manual is available for download in different languages through the following links: www.vector.com/manuals/vtc8920-en/

SAFETY INSTRUCTIONS
Please observe the safety instructions on the module and read the safety instructions as well as the user manual before putting the device into operation. Otherwise, persons could be injured or the module could be damaged. The module VTCB920B is operated With line voltage.

Install or remove only when de-energized.
Installation, initial operation and use have to be done by qualified personal.
Approved only for the connection values given on the rating plate and in the technical data.

Use only in a grounded 41—1 19′ frame!

For connection to mains a cord set with an IEC 60320 C13 appliance coupler and a suitable county-dependent mains plug is required. Mains plug: Class l; voltage rating suitable for the intended mains system. Cord: cross-sectional area min. O, 75mrn2/ ld AWG Cord type according to national requirements.
The module must be connected to a socket outlet with earthing contact.
Secure the module with pre-assembled screws and install it in the rightmost slot.
The power switch must be accessible at any time. Fire protection must be ensured by the 19′ frame.
During operation, do not store flammable substances near the module.
Manipulations in the device are not permitted.
Repairs are carried Out by the manufacturer.

For Japan: This product is not covered by the Electrical Appliances and Materials Safety Act.

POWER SUPPLY UNIT VTC8920B

GENERAL INFORMATION

Please observe the safety instructions on the module and read the safety instructions as well as the user manual before putting the device into operation. Otherwise, persons could be injured or the module could be damaged.
This is a Class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
DOUBLE POLE/NEUTRAL FUSING

The module VTC8920B is operated with line voltage.

Install or remove only when de-energized.
Installation, initial operation and use have to be done by qualified personal.
Approved only for the connection values given on the rating plate and in the technical data.
Use only in a grounded 4U 19″ frame!
For connection to mains a cord set with an IEC 60320 C13 appliance coupler and a suitable county-dependent mains plug is required. Mains plug: Class I; voltage rating suitable for the intended mains system. Cord: cross-sectional area min. 0,75 mm²/18 AWG Cord type according to national requirements.
The module must be connected to a socket outlet with earthing contact.
Secure the module with pre-assembled screws and install it in the rightmost slot.
The power switch must be accessible at any time.
Fire protection must be ensured by the 19″ frame.
During operation, do not store flammable substances near the module.
Manipulations in the device are not permitted.
Repairs are carried out by the manufacturer.

Terms, Explanations

Support

You can reach us at [email protected] or by phone at +49 7151 25027-10.

VTC8920B
Purpose
The module VTC8920B is a 12V power supply for measuring and test devices in the laboratory sector.

Shape and size are adapted to the VT system of Vector Informatik GmbH.
May only be operated with VT and VTC components in a grounded 4U 19″ frame.
Suitable for IT mains up to 240VAC.
The module is used exclusively in an industrial electromagnetic environment.
Only indoor use at an ambient temperature of 0–40°C, max. altitude of 4,000m and a relative humidity of 90%.
Make sure that pollution degree 2 or better is maintained

Initial Operation

Mount the module in a grounded 4U 19″ frame with the supplied screws.
Connect the 6.3mm flat connector (X5) to the grounded 4U 19″ frame for potential equalization (functional earth).
Connect the mains cord to the power supply unit before connecting it to the mains socket outlet.
In the user manual of the VT-System you find a chapter “Supply Voltage and Ground” and a chapter “VT8006A/VT8012A” with hints for the connection of analog GND with digital GND at the 4-pin connector MSTB 2.5HC/ 4-ST-5.08

Usage

The device is switched on and off via the power switch on the front.
The module was developed for the supply of VT modules via the backplanes VT8006A and VT8012A, as well as for VTC modules.
The connection values of the connected modules must not exceed the performance data of the VTC8920B.
Customer-specific applications must be coordinated with ibb testing gmbh.

Connectors

Accessories

supply cable VTC8920B_12V
cable for functional earthing at X5
country-specific mains cord set
plug for output connector 12V: Phoenix MSTB 2.5/ 2-ST-5.08

Technical Data

Maintenance, Repair and Disposal

No maintenance tasks and repairs.
If necessary, clean the front panel with a soft cloth.
In case of a defect, you are welcome to send the device back to us. We will give you a cost estimation for the repair or provide you with a replacement device.
We also ensure the proper disposal of the old device.

ibb testing gmbh
Zeppelinstraße 14
71332 Waiblingen, Germany
+49 7151 25027-0
[email protected]
www.ibbtesting.de