ofinto CH-9200 More Ergonomic Ergo Office Chair User Manual
- June 10, 2024
- ofinto
Table of Contents
ofinto CH-9200 More Ergonomic Ergo Office Chair
THANK YOU!
Thank you for choosing the ofinto ergonomic chair Ergo!
It provides you with the optimal conditions for active, dynamic sitting and healthy working. The ergonomic chair Ergo combines ergonomics with comfort and enables a healthy posture while sitting. However, only if your chair is correctly assembled, configured and customized can it fulfill all ergonomic aspects. This User Manual is intended to help you with these settings.
Your feedback is important to us! Please leave us your rating for the ofinto
ergonomic chair Ergo online at www.
en.ofinto.ch. If you have any questions, comments or suggestions for
improvement, please contact us at any time via our online customer service.
And now, enjoy sitting!
WARNING!
Please read the instructions and safety precautions carefully before using the
office chair. Keep the assembly instructions for further use. If you pass on
the swivel chair to a third party, make sure to include these assembly
instructions.
ofinto ag assumes no liability for damage caused by the improper use of the
office chair
DELIVERY CONTENTS
COMPONENTS & TOOLS
Ⓐ Seat & Mechanism
Ⓑ Armrests
Ⓒ Backrest
Ⓓ Gas spring
Ⓔ Footbase
Ⓕ Castors
Ⓖ Screws M640mm
Ⓗ Screws M820mm
Ⓘ Split lock washers 813mm
Ⓙ Screws M645mm
Ⓚ Washers 8*20mm
Ⓛ Hex key 5mm
ASSEMBLY
Help and videos regarding the assembly can be found here:
Press castors firmly into the
footbase!
CONTROLS
Videos regarding the controls of the chair can be found here:
SEAT HEIGHT
SEAT DEPTH
ARMRESTS
LUMBAR SUPPORT
BACKREST
CORRECT SETUP
You can adjust the swivel chair in seat height, seat depth and backrest
inclination. This enables you to achieve an ergonomic sitting position. An
upright sitting posture strengthens your spine. Make sure that you place your
legs at an angle of slightly more than 90° and your feet completely on the
floor. The seat height is correctly adjusted when your knee is slightly lower
than your hip.
The length of your legs determines the seat depth. It is correctly adjusted
when there is a distance of about three fingers between the edge of the seat
and the calf when the pelvis is in very good contact with the backrest.
Adjust your armrests so that both shoulders are horizontal in a relaxed
position while your forearms rest on the armrests. The arm angle should be at
least 90°. The width of the armrests depends on the width of your shoulders.
When adjusted correctly, your arms are close to your torso while resting on
the armrests. However, your freedom of movement must not be restricted.
Adjust the height of the lumbar support so that the strongest tension of the
seat fabric is at the level of the lumbar vertebrae, i.e. approximately on the
waistline. The lumbar support helps relieve pressure on your spine when
sitting for long periods of time and supports your lower back in its natural
shape.
Your chair has a resistance mechanism that automatically adjusts to your body
weight. So, the backrest will alwaysprovide you with ideal support as you move
forward and backward due to the automatic resistance. Generally, it is
healthier to move around while sitting, so set the back of your chair to move.
This extra moving can help prevent negative effects from sitting all the time.
PRODUCT SPECIFICATIONS
WEIGHT & DIMENSIONS
Product weight: approx. 17 kg
Max. load: 130 kg
Chair height: min. 98 cm max. 108 cm
Seat height: min. 43 cm max. 53 cm
Seat depth: min. 46 cm max. 51 cm
Backrest: 45 cm x 55 cm (W x H)
SPECIFICATIONS
- Soft castors for hard floors (see next page)
- Synchronous inclination adjustment (synchronous mechanism) with locking button
- 4 tilt lock positions with anti-shock lock
- Seat slide function with 5 cm adjustment
- Adjustable lumbar support
- Class 4 gas spring with a stroke of approx. 10 cm (TÜV LGA tested according to DIN EN 16955:2017)
- Durability certified according to ANSI/BIFMA X5.1-2017 safety standard (Type I, III)
- Ergonomics certified by IGR Institute for Health and Ergonomics according to DIN EN ISO 26800 / EN ISO 15537
SAFETY INSTRUCTIONS AND HAZARD WARNINGS
Only trained technicians may work on or replace gas springs for adjusting the seat height. They may never be replaced or repaired independently by the user. In case of independent repairs, liability and warranty claims expire. In addition, personal injury and damage to property may occur. ofinto ag does not accept any liability for damage caused by improper or incorrect use.
The office swivel chair is designed exclusively as a seating option for individual persons with a maximum weight load of 130 kg. It must never be used as a substitute for a ladder, as a stand, as a gymnastics apparatus for children or similar.
Proceed carefully during installation and follow these installation instructions. Improper assembly, as well as failure to comply with or disregard the instructions and warnings regarding the use of this product may result in damage to property and/or injury.
Place the swivel chair indoors only and always place it on a level and dry floor. Plastic and metal react to stress and temperature influences by expanding and contracting. Check all screw connections regularly and tighten them if necessary. Loose screw connections can lead to personalinjury. Do not use the swivel chair if screw connections have become loose or if the metal or plastic parts are deformed, cracked or otherwise damaged.
The chair is equipped with high-quality polyutherane castors. These are suitable for hard as well as soft floors. For particularly delicate floors we recommend the use of a floor protection mat. ofinto is not liable for any damage to the floor.
Do not have the swivel chair dismantled by non-instructed persons. This can lead to injury or damage.
Do not expose the swivel chair to weather conditions, e.g. rain. Protect the office chair from direct sunlight, otherwise the color of the textiles may change. Also remember that zippers, sharp-edged buttons or rivets on garments may cause damage to the cover. Individual parts such as armrests or castors may only be replaced independently after consultation with the ofinto customer service.
CARE INSTRUCTIONS
CLEANING
A vacuum cleaner can be used to remove dust and lint from the cover. Use a damp soft cloth and a mild, neutral detergent to treat stains on the cover and the surface.
For stubborn stains please consult a specialist.
Use a dry cloth to remove dust and dirt from the underside of the seat, the back of the backrest and the base.
Do not use aggressive cleaning agents, hard brushes, sharp or metallic cleaning objects such as knives, metal sponges and the like. These can damage the surfaces. Never clean the gas pressure spring
MAINTENANCE
Occasionally remove dust and carpet fluff from the castors to ensure that the castors can move.
Regularly check all screw connections for tightness and tighten them if necessary. Loose screw connections impair safety and there is a risk of injury.
Before using or storing the swivel chair again, wait until all parts are completely dry or dry them with a dry cloth.
STORING AND DISPOSAL
STORING
All parts must be completely dry before storing.
Always store the office chair in a dry place, protected from dust and inaccessible to children.
DISPOSAL
Keep packaging materials away from children and recycle them in the interest of environmental protection. Add cardboard and paperboard to the waste paper, foils to the recyclable material collection.
When the chair is no longer of use, contact your local waste disposal service for information on environmentally friendly disposal. By disposing of the chair separately, you can help reduce waste and reduce potential negative impact on human health and the environment.
Bischofszellerstrasse 35
CH-9200 Gossau SG
info@ofinto.ch| www.ofinto.ch
References
- Buy the best ergonomic office furniture online | 30 days test | ofinto ®
- Beste ergonomische Büromöbel online kaufen | 30 Tage testen | ofinto ®
- Beste ergonomische Büromöbel online kaufen | 30 Tage testen | ofinto ®