STANLEY SXLS36986E LED Area Globe Light Instruction Manual
- June 10, 2024
- Stanley
Table of Contents
STANLEY SXLS36986E LED Area Globe Light
Product Information
- Supply Voltage: 220-240 V~ 50 Hz
- Bulb Type: Non-replaceable 30W LED
- Conformity with all relevant EC and UK Directive requirements
- Class I product, must be connected to earth
- IP54: Protects against dust and low-pressure jets of water from all directions. Limited ingress permitted
- Warranty: 2-Year Limited Warranty covered by Cascade Holdings Ltd.
- Manufacturer: Cascade Holdings Ltd. Gorse Mill, Gorse St Oldham, OL9 9RJ U.K.
- Additional Features: Magnetic base. Adaptor – the lamp can be used on a Tripod. (Item SXLS37627E)
Product Usage Instructions
- Ensure there is no electricity failure before using the product.
- Connect the product to the power supply of 220-240 V~ 50 Hz.
- Secure all the connections before turning the product on.
- The product is a Class I product and must be connected to the earth.
- The product has an IP54 rating that protects against dust and low-pressure jets of water from all directions. Limited ingress is permitted.
- The product has a non-replaceable 30W LED bulb type.
- Do not stare at the operating LED light source.
- Always disconnect the product from mains at least 10 minutes allowing it to cool down before any maintenance or adjustment.
- The product can be cleaned with a clean dry cloth. Do no immerse it in water. Always switch off the supply before cleaning.
- The product comes with an extension socket and a storage hook.
- The product has a magnetic base and can be used on a tripod with the adaptor (Item SXLS37627E).
- Do not dispose of the product with household waste. Please recycle where facilities exist. Check with your Local Authority or local store for recycling advice.
LED Area Globe Light
SAVE THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE
The thick and thin horizontal line field and the engineering plan packaging
design are trademarks of Stanley Tools.
CUSTOMER SUPPORT
For customer service please visit the Online Customer Service Centre at:
www.2helpU.com
2-YEAR LIMITED WARRANTY
The warranty of this product is covered by Cascade Holdings Ltd.
© Stanley Black & Decker, Inc.
STANLEY and the STANLEY Logo are trademarks of Stanley Black & Decker, Inc or
one of its afiliates, and are used under license.
- Products are manufactured by: Eu Authorised Representative:
- Cascade Holdings Ltd. : Authorised Rep Compliance
- Gorse Mill, Gorse St : Ground Floor
- Oldham, OL9 9RJ U.K. : 71 Lower Baggot Street
- www.stanleytools.co.uk : Dublin Ireland D02 P593
Technical Data
- Supply Voltage: 220-240 V~ 50 Hz
- Bulb Type: Non-replaceable 30W LED
- Conformity with all relevant EC and UK & Directive requirements.
- Class I product, must be connected to earth.
- IP54 : Protects against dust and low pressure jets of water from all directions. Limited ingress permitted.
- Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or local store for recycling advice.
READ ALL INSTRUCTIONS
Safety
- These instructions are for your safety. Please read through them thoroughly prior to installation and retain them for future reference.
- Always organise cables and extension leads so that they will not be a trip hazard
- If the external flexible cable or cord of this Luminaire is damaged, it must only be replaced by a qualified electrician to avoid any electrical hazards.
- Check the pack and make sure you have all of the parts listed.
- Remove all packaging, wrap etc. from the product.
- Decide on the appropriate location for your product.
- IP54 product: Protects against dust and low pressure jetsof water from all directions.
- Limited ingress permitted.
- Always refer to the installation drawing for the orientation of the product.
- Never put anything on the product or hang anything on any part of this product.
- When the product does not light after installation:
- Ensure there is no electricity failure
- Ensure all the connections are secured
- Always disconnect the product from mains at least 10 minutes allowing to cool down before any maintenance or adjustment.
- CAUTION: Do not stare at the operating LED light source.
Cleaning care
- The lamp can be cleaned with a clean dry cloth. Do not immerse it in water.
- Always switch off the supply before cleaning.
Parts Supplied
Installation Instructions
Additional features
Magnetic base
Adaptor – the lamp can be used on a Tripod. (Item SXLS37627E)
Images for illustration purposes only – Product may differ slightly from the one shown.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>