Mircom MGC-CONFIG-KIT4 Secutron Fire Alarm Control Panels and Voice Evacuation System Instructions

June 10, 2024
Mircom

CONFIG-KIT4 Secutron Fire Alarm Control Panels and Voice Evacuation System
Instructions

Contents of the Kit

Name Photo Description
UIMA4 interface • For configuring the following products:

• FleX-Net™ and FleX-Net™ FX-4000
• FA-300
• FX-350
• FX-2000
• FX-3500
• FX-3318
• QX-5000
•UDACT-300
• MR-2300 and MR-2350
• MMX™
• For use with the FleX-Net™ MP Upgrade Wizard
• Includes one replacement 10 pin cable
UIMA4
9 pin male to female serial
cable| | • For use with the FleX-Net™ MP Upgrade Wizard to connect the UIMA4 interface to FleX-Net™, FleX-Net™ FX-4000, MMX™, RAXN-LCD(G) and RAXN- 4000LCD(G)
MD-508
10 to 8 Pin Adapter| | • For use with the FleX-Net™ MP Upgrade Wizard to connect the UIMA4 interface to ANC-5000, ANC-4000 and ALCN-792M
RPL-MD-1211
USB A to B Male Cable| | • For use with the following products:
• FX-400 and FX-401
• FX-3500
• FX-3318
•QX-mini
• AUDMAX-MASTER
• ALCN-792MISO and ALCN-4792MISO
• ALCN-960MISO
WC-100011
UIMA4 Driver Installation
Instructions| | • Refer to this manual for instructions on installing the drivers for the UIMA4 interface
LT-6231
FleX-Net™ MP Upgrade Wizard Manual| | • Refer to this manual for instructions on using the FleX-Net™ MP Upgrade Wizard
LT-6232

The UIMA4 Interface

The UIMA4 interface has 3 connectors.

  • 9 pin male serial connector for connecting the UIMA4 to the 9 pin male to female serial cable and then to the RS-232 serial port on some productsMircom MGC CONFIG KIT4 Secutron Fire Alarm Control Panels and Voice Evacuation System - Interface
  • USB B female connector for connecting the UIMA4 to the USB A to B male cable and then to the computerMircom MGC CONFIG KIT4 Secutron Fire Alarm Control Panels and Voice Evacuation System - Interface 14
  • 10 pin female connector for connecting the UIMA4 to the configuration port or debug interface on some productsMircom MGC CONFIG KIT4 Secutron Fire Alarm Control Panels and Voice Evacuation System - Interface 15The 10 pin cable can be disconnected and replaced if necessary. This kit includes one replacement cable. If you need more replacement cables, use the Mircom part number RPL-WC-25022.

2.1 To disconnect the 10 pin cable

  1. Insert a small flathead screwdriver in one of the grooves on the side of the case, then turn the screwdriver to open the case.
  2. Disconnect the 10 pin cable from the board (see picture below).Mircom MGC CONFIG KIT4 Secutron Fire Alarm Control Panels and Voice Evacuation System - pin cable

Install Software

3.1 Install UIMA4 Driver
Refer to the included manual LT-6231 for instructions on installing the driver for the UIMA4 interface.

Connections for Configuration

Attention: Always connect the UIMA4 interface to the computer first, before connecting it to the fire alarm product.
4.1 Computer to FleX-Net™, FleX-Net™ FX-4000, MMX™, FA-300, FX-350, FX-2000, MR-2300, MR-2350, QX-5000, UDACT-300A, DTC-300A, DTC-300A-2

Mircom MGC CONFIG KIT4 Secutron Fire Alarm Control Panels and Voice
Evacuation System - Audio Controller

See the table below for the connector designation that the 10 pin UIMA4 connects to.

Panel Connector
FleX-Net™ P3 on FIeX-Net™ main board and on ALCN-792M(ISO), P4 on ALC-386S,

and P10 on ANC-5000
FIeX-Net™ FX-4000| P3 on the FIeX-Net™ FX-4000 main board, ALCN-4792MISO and ALCN-960MISO, and P10 on ANC-4000
MMXT”| P3 on MMXTM main board and on ALCN-792M(ISO), P4 on ALC-386S, and P10 on ANC-5000
FA-300| P9
FX-350| P5
FX-2000| P3 on FX-3500 main board, P4 on ALC-386S, ALC-198S, and ALC-H16
MR-2300| P9
MR-2350| P5
QX-5000| J9 on 01F-5000B
U DACT-300A, DTC-300A, DTC-300A-2| P2

4.2 Computer to FX-400, FX-401, FX-3500, FX-3500RCU, FX-3318, MR-3500, MR- 3500RCU, MR-3318, QX-mini, AUDMAX-MASTER

Mircom MGC CONFIG KIT4 Secutron Fire Alarm Control Panels and Voice
Evacuation System - Audio Controller 1

Connect the cable to the USB port on the main board.

Connections for the FleX-Net™ MP Upgrade Wizard

Attention: Always connect the UIMA4 interface to the computer first, before connecting it to the fire alarm product.
Note: Refer to the included manual LT-6232 for instructions on using the FleX-Net™ MP Upgrade Wizard.
5.1 Main CPU on FX-2000N, FX-4000N and MMX-2000N Series Panels

Mircom MGC CONFIG KIT4 Secutron Fire Alarm Control Panels and Voice
Evacuation System - Audio Controller 2

On FX-4000N boards, turn switch 7 of SW2 ON and switch 8 of SW2 OFF in order to use the FleX-Net™ MP Upgrade Wizard. After the firmware upgrade is complete, turn both switch 7 and switch 8 OFF.
5.2 RAXN-LCD(G) and RAXN-4000LCD(G) Remote Annunciator

Mircom MGC CONFIG KIT4 Secutron Fire Alarm Control Panels and Voice
Evacuation System - Audio Controller 3

5.3 ANC-5000 and ANC-4000 Audio Controller

Mircom MGC CONFIG KIT4 Secutron Fire Alarm Control Panels and Voice
Evacuation System - Audio Controller 4

5.4 ALCN-792M Loop Controller

Mircom MGC CONFIG KIT4 Secutron Fire Alarm Control Panels and Voice
Evacuation System - Loop Controller

5.5 ALCN-792MISO, ALCN-4792MISO and ALCN-960MISO Loop Controllers

Mircom MGC CONFIG KIT4 Secutron Fire Alarm Control Panels and Voice
Evacuation System - Loop Controller 1

We want your feedback!
Please let us know how we can improve your experience with the UIMA4 interfaces.
Mircom
25 Interchange Way
Vaughan, ON L4K 5W3
Canada
Tel: 1-888-647-2665
http://www.mircom.com

LT-6230 Rev 2 January 2022

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Mircom User Manuals

Related Manuals