sygonix 2623641 3000W Compact Instant Water Heater Instruction Manual
- June 10, 2024
- Sygonix
Table of Contents
Operating instructions
Compact instant water heater, 3000 W ****
Intended use
The product provides hot water at frost-protected cold water connections. The
product is intended for indoor use only. Do not use it outdoors.
The product is IP24 rated and protected against water splashes from any
direction. It must not be immersed in water. It must only be connected to
standard domestic cold water outlets. A splash-proof grounded socket must be
located right near the water connection. You can adjust the water temperature
at the outlet.
Using the product for purposes other than those described above may damage the
product. Improper product use can cause a short circuit, fire, electric shock,
other hazards. This product complies with statutory, national and European
regulations. For safety and approval purposes, you must not rebuild and/or
modify the product.
Read the instructions carefully and store them in a safe place. Always provide
these operating instructions when giving the product to a third party. All
company and product names contained herein are trademarks of their respective
owners. All rights reserved.
Delivery content
- Product
- brass adaptors
- 3 silicone O-rings
- Universal hose adapter
- Male to female reducer (M30/G3/4”)
- Operating instructions
Latest product information
Download the latest product information at www.conrad.com/downloads or scan the QR code shown. Follow the instructions on the website.
Explanation of symbols
****The following symbols appear on the product/device or in the text:
This symbol warns of hazards that can lead to injury.
This symbol warns of a dangerous voltage which can lead to injuries due to
electric shock.
Safety instructions
**Read the operating instructions carefully and especially observe the
safety information. If you do not follow the safety instructions and
information on proper handling, we assume no liability for any resulting
personal injury or damage to property. Such cases will invalidate the
warranty/guarantee.
5.1 General information
This product is not a toy. Keep it out of the reach of children and pets.
Do not leave packaging material lying around carelessly. It may become a
dangerous plaything for children.
Should you have any questions or concerns after reading this document, please
contact our technical support or a professional technician.
Maintenance, modifications and repairs must be carried out by a technician or
a specialist repair centre.
5.2 Handling
Please handle the product carefully. Impact, shocks or a fall even from a low
height can damage the product.
5.3 Operating environment
Do not expose the product to any mechanical stress.
Protect the product from extreme temperatures, strong jolts, flammable gases,
vapours, and solvents.
Protect the product from direct sunlight.
Never switch the device on immediately after taking it from a cold into a warm
environment.
This may cause condensation to form, which can destroy the product. Allow the
product to reach room temperature before using it.
5.4 Operation
Consult an expert when in doubt about the operation, safety or connection of
the device.
If it is no longer possible to operate the product safely, take it out of
operation and protect it from any accidental use. DO NOT attempt to repair the
product yourself. Safe operation can no longer be guaranteed if the product:
– is visibly damaged,
– is no longer working properly,
– has been stored for extended periods in poor ambient conditions or
– has been subjected to any serious transport-related stress.
5.5 Power cord
Do not modify or repair power supply components, including power plugs, power
cords and power adapters. Never use damaged components. Danger of death from
electric shock!
The mains outlet must be located near the device and be easily accessible.
The device must only be connected to a grounded socket. Do not use multiple
sockets or extension cords.
Never plug in or unplug the mains plug when your hands are wet.
Never disconnect the mains plug from the socket by pulling on the cable.
Always pull it out of the mains socket using the intended grips.
Unplug the mains plug from the mains socket if you do not use the device for a
long time.
Unplug the device from the power outlet during a thunderstorm for safety
reasons.
Make sure that the power cord is not squeezed, bent, damaged by sharp edges or
put under mechanical stress.
Avoid excessive thermal stress on the power cord from extreme heat or cold.
Do not modify the power cord. Otherwise the power cord may be damaged. A
damaged power cord can cause a fatal electric shock.
Do not touch the power cord if it is damaged.
– First, power down the respective mains socket (e.g. via the respective
circuit breaker), and then carefully pull the mains plug out of the mains
socket.
– Never use the product if the power cord is damaged.
A damaged power cord may only be replaced by the manufacturer, a workshop
commissioned by the manufacturer or a similarly qualified person to prevent
any danger.
Make sure that the cable is not pinched, kinked or damaged by sharp edges.
Always lay cables so that nobody can trip over or become entangled in them.
Failure to do so could result in injury.
5.6 Connected devices**
Always observe the safety information and operating instructions of any other
devices connected to the product.
Product overview
Installation
****Always install the instant water heater on the water connection before
plugging it into the grounded socket. Follow the reverse order to disassemble.
The device comes with three different connection adaptors that fit the most
popular water connections. Use the adapter that fits your connection.
Always use the supplied precision-fit silicone O-ring for each adapter. Ensure
that the screw connections are secure and tight.
The instant water heater should only be installed in a vertical position! The
water outlet must always face downwards.
Use the thread adapter that fits your connection:
Connection examples: Connection to a water tap with male thread
Universal connection (hose connection) with clamp ring
Connection to a water tap with female thread (optional)
Matching thread adapters for taps with female thread are available at
specialist shops. The instant water heater connection has an M22 female
thread.
Operation
The instant water heater features integrated dry-run protection. The heater
only kicks in when water flows through the device and the hot mode has been
set.
Use the controller (4) on the side to adjust the flow rate and water
temperature. The heating power depends on the flow rate. When in the middle
position, the flow rate is limited by a spray jet at the outlet. This position
provides the hottest water. Setting the controller to the red area (HOT)
increases the flow rate but reduces the water temperature.
Setting the controller to the black area (COLD) shuts the heater off. Turning
the controller further into the black area (COLD) increases the flow rate.
Water temperature is not displayed in the cold water range.
Turning the controller to either of the two end positions produces an audible
click to indicate the maximum flow rate.
When you close the water tap, the instant water heater switches off
automatically. When in hot mode, the temperature display turns off.
Troubleshooting
| Error | Cause | Remedy |
|---|---|---|
| Temperature display is blank | No power supply |
No water flow
Controller set to cold mode| Connect the power plug Open the water tap
Set the controller to the middle position or the red area.
Water is not hot enough| The flow rate is too high.| Turn the controller to
the
middle position.
Water is too hot| The water inlet is blocked. The water flow is low.| Check
the water inlet and clean it.
Open the water tap further.
The heater will not kick in.| The water flow is too low.| Open the water tap
further.
Inconsistent water stream
from a faucet.| The bead nozzle at the out- let is soiled.| Remove the bead
nozzle at the outlet and clean it (descale).
The heater does not work, but the temperature is dis- played.| The internal
circuit breaker or overload/overtemperature protection has tripped.| Reset the
instant water
heater.
Resetting the temperature and overload protection (Reset)
If the instant water heater stops working, check whether the internal circuit
breaker has tripped.
The reset button is concealed. Before resetting, unplug the device from the
power outlet.
Pull the cap on the controller gently to the side of the device to access the
reset button. Push the reset button until it clicks. You may need a suitable
screwdriver to do this.
Replace the cap and plug the device back into the power outlet. The instant
water heater should now work again.
If the instant water heater will not start, disconnect it and contact customer service.
Cleaning and care
Important:
– Do not use aggressive cleaning agents, rubbing alcohol or other chemical
solutions.
They can damage the housing and can cause the product to malfunction.
– Do not immerse the product in water.
- Disconnect the product from the power supply.
- Use a damp, lint-free cloth to clean the product.
- Clean the water inlet and outlet, if necessary. Use a natural limescale remover (e.g. cleaner with citric acid, etc.). Thoroughly rinse the cleaned parts with clear water.
Disposal
11.1 Product
****This symbol must appear on any electrical and electronic equipment placed
on the EU market. This symbol indicates that this device should not be
disposed of as unsorted municipal waste at the end of its service life.
Owners of WEEE (Waste from Electrical and Electronic Equipment) shall dispose
of it separately from unsorted municipal waste. Spent batteries and
accumulators, which are not enclosed by the WEEE, as well as lamps that can be
removed from the WEEE in a non-destructive manner, must be removed by end
users from the WEEE in a non-destructive manner before it is handed over to a
collection point. Distributors of electrical and electronic equipment are
legally obliged to provide free take-back of waste. Conrad provides the
following return options free of charge (more details on our website): in our
Conrad offices at the Conrad collection points at the collection points of
public waste management authorities or the collection points set up by
manufacturers or distributors within the meaning of the ElektroG It should be
noted that different obligations about the return or recycling of WEEE may
apply in countries outside of Germany.
Technical data
12.1 Power supply
Input voltage …………………………… 220 – 240 V/AC, 50/60 Hz
Power consumption …………………. 3000 – 3600 W
Power cord length ……………………. approx. 110 cm
Protection class ………………………. 1
IP rating …………………………………. IP24 (splash-proof)
12.2 Ambient conditions
Operating temperature …………….. frost-free
Water pressure ……………………….. 0.04 – 0.4 MPa
Outlet water temperature ………….. max. 50 °C
Water inlet connection ……………… M22 female thread
12.3 Miscellaneous
Dimensions (W x H x D) …………… 138 x 118 x 65 mm
Weight …………………………………… approx. 0.8 kg
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240
Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g.
photocopy, microfilming, or the capture in electronic data processing systems
require the prior written approval by the editor. Reprinting, also in part, is
prohibited. This publication represent the technical status at the time of
printing.
Copyright 2023 by Conrad Electronic SE.
*2623641_V3_0523_dm_mh_EN
Item no. 2623641
Documents / Resources
|
sygonix 2623641 3000W Compact Instant Water
Heater
[pdf] Instruction Manual
SY-5247282, 2623641 3000W Compact Instant Water Heater, 2623641, 3000W Compact
Instant Water Heater, Compact Instant Water Heater, Instant Water Heater,
Water Heater, Heater
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>