packed party LY300 Wireless Headphone User Guide
- June 10, 2024
- packed party
Table of Contents
eureka NEC580 Series Lightweight Cordless Vacuum Cleaner
What’s in the Box?
A. l pair wireless headphones
B. l micro USB c harging cable
C. l quick start guide
Initial Setup
-
Use the included micro USB charging cable to connect your headphones to a power source and charge your device for about 3 hours
-
Once your headphones are fully charged, press and hold the POWER button for 2 seconds until the indicator light blinks red and blue. Your headphones are now in pairing mode.
-
On your smartphone or tablet, search for the Bluetooth®device named “Turn It Up Wireless Headphones” and tap to connect. A blinking blue indicator light will confirm successful pairing .
Button Functions
| PREVIOUS/VOLUME
Press and hold to decrease volume.
Press once to play the pre-vious track.
---|---
| POWER
Press and hold for 2 seconds to turn on your device
Press and hold for 4 seconds to turn off your device.
Press once to PLAY, Press again to PAUSE.
Press 3x for Siri®.
| NEXT/VOLUME+
Press and hold to increase volume.
Press once to play the next track
Answering Phone Calls
| VOLUME
Press and hold to decrease volume
---|---
| POWER
Press once to answer a call. Press again to hang up.
Press and hold to reject a call.
| VOLUME+
Press and hold to increase volume.
Bluetooth® Pairing
After initial Bluetooth® pairing, your headphones will automatically connect to the previous paired device when turned on
To pair your headphones to a new device:
- Disable Bluetooth® on your previously connected device.
- Press and hold the POWER button on your headphones for 2 seconds to enter Bluetooth® pairing mode. The LED light on your headphones will blink red and blue, indicating that pairing mode is active.
- On the new device you wish to pair, search for the Bluetooth® device named “Turn It Up Wireless headphones” and tap to connect. A blinking blue light will confirm successful pa1nng.
The Specs
| Model | LY300 |
|---|---|
| Bluetooth ® | Bluetooth® 5.3 |
| Speaker Rated Output Power | lOmW |
| Impedance | 32 ohms |
| Sensitivity | 105 DB + / – 3 DB |
| Frequency Response | 20 HZ – 20 KHZ |
| Play Time | Over 14 hours ( 50% volume} |
| Power Charge | about 3 hours |
| Battery | Rechargeable Lithium-ion |
3.7V, 250 MAH
Microphone| Built-In
Transmission Distance| 32.8 ft ( 10 meters)
a t an environment without
wall b locking
Need Help?
For customer support regarding your device, please submit a request by
emailing techsupport@packedparty.com.
Please make sure to note the model 1number and a description of your 1nqu1ry.
Thank you for purchasing a Packed Party product.
Designed in Austin, Texas. Made in China. All designs© 2023 Packed Party, Inc. All Rights Reserved.© 2023 Bluetooth SIG, Inc. All rights reserved. The Bluetooth® trademarks–including the BLUETOOTH word mark, the figure mark (the runic “B” and oval design), and the combination mark (Bluetooth word mark and design) — are owned by the Bluetooth SIG. USB is used to solely describe the compatibility of our technology and in no way is intended to infringe on any intellectual property rights of any respective protected marks. Siri® is a registered trademark of Apple Inc. Packed Party is a registered trademark of Packed Party, Inc.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: ( 1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution: Changes or modifications to this product not expressly approve by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to connect the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure condition as without restriction.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>