FHM FH-ECO19 2 Way Feed Chipper Shredder Owner’s Manual

FHM FH-ECO19 2 Way Feed Chipper Shredder

Product Information: FH-ECO19 Chipper Shredder 2-Way Feed

The FH-ECO19 Chipper Shredder 2-Way Feed is a machine designed to chip and shred branches and debris. It comes with an adjustable stand, and its model number is EC019.001. The chipper/shredder should be used by individuals who have read and understood the safety instructions mentioned in the user manual. The user manual contains important safety instructions and is considered a permanent part of the chipper/shredder. Betstco provides customer service for product inquiries or services, and their contact information can be found in the user manual.

Product Specifications:
The product specifications for the FH-ECO19 Chipper Shredder 2-Way Feed are not mentioned in the user manual.

Product Usage Instructions

1. Before using the chipper/shredder, the user should read and understand all the safety instructions mentioned in the user manual.
2. Remove the chipper from its carton and verify that all parts are present in the chipper carton.
3. Do not put branches into the chipper funnel. Branches should be fed into the side chipper chute.
4. Always wear hearing and eye protection while operating this machine or if you are within 75 feet of this machine.
5. Always stop the engine, disconnect spark plug, and ground against the engine before cleaning, lubricating, or performing any maintenance on your machine.
6. If the chipper becomes clogged, always stop the engine, disconnect spark plug, and ground against the engine before cleaning, lubricating, or performing any maintenance on your machine.
7. For removing and sharpening the blade, follow the instructions mentioned in the user manual.
8. For changing or tightening the belt, follow the instructions mentioned in the user manual.
9. This machine does not have wheels. It has stand legs.
10. For cleaning and storing the chipper/shredder, follow the instructions mentioned in the user manual.

OPERATION & PARTS MANUAL
Please read these instructions before using. Always grease all fittings and be sure to always check and fill with oil before operating! Retain this manual for future use.
BETSTCO www.Betstco.com
541-895-3083 M-F 7am-4pm PST RUGGED LABOR SAVING EQUIPMENT SINCE 1995
83371 Melton Rd, Creswell OR 97426

The intonation and specifications included in this publication ware in affect at the time of approval for printing.

For product questions or service,
CALL 1-541-895-3083
or go to www.betst.com
When you call the help-line you will need to have the following information:

• Date of Purchase: ___
• Location of Purchase: ___
• Serial #: ___

This manual contains important safety instructions for Chipper/Shredders
READ SAFETY WARNINGS AND OPERATING INSTRUCTIONS CAREFULLY SAVE THESE INSTRUCTIONS.

This owner’s manual is considered a permanent part of the chipper/shredder and should remain with the chipper/shredder if resold.

WARNING
This symbol indicates important safety instructions which, if not followed, could endanger personal safety and/or property. Read and follow all instructions in this manual before attempting to operate this machine. Failure to comply with these instructions may result in personal injury. When you see this symbol—heed its warning.

WARNING
CARBON MONOXIDE GAS
Exhaust contains poisonous carbon monoxide, a colorless and odorless gas. Breathing exhaust can cause loss of consciousness and may lead to death. The Engine Exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm.

WARNING
This machine has a rotating cutting blade capable of amputating hands and feet and throwing objects. Keep hands and feet out of openings while machine is running. Failure to observe these safety instructions could result in serious injury or death.

WARNING
WARNING: Do not operate this machine unless the chute deflector has been installed properly.

WARNING
Keep bystanders, helpers, pets, and children at least 75 feet from the machine while it is in operation. Stop machine if anyone enters the area.

WARNING
Wear hearing and eye protection while operating this machine or if you are within 75 feet of this machine. Thrown objects which ricochet can cause serious injury to the eyes.

WARNING
Never wear loose clothes or long jewelry and keep your long hair under a headgear when operating machine. Never operate this machine in bare feet or sandals. Never use machine on a slope or hard smooth floor.

WARNING
Gasoline is extremely flammable and the vapors are explosive. Serious personal injury can occur when gasoline is spilled on you or your clothing, which can ignite. In the event of a gasoline spill, wash your skin anc change clothes immediately.

WARNING: Do not deposit branches larger than 3″ × 4″ inches in diameter (depending on Model #, see Model Specifications table pg 2) in the side chute. Do not deposit branches larger than 1/4 inches into the funnel. DO NOT force the branches into this machine, allow the machine to automatically feed through.

Training

1. Read, understand, and follow all instructions on the machine and in the manual) before attempting to assemble and operate. Keep this manual in a safe place for future and regular reference and for ordering replacement parts.
2. Be familiar with all controls and their proper operation. Know how to stop the machine and disengage them quickly.
3. Never allow children under 18 years old to operate this machine. Children 18 years old and over should read and understand the operation instructions and safety rules in this manual and should be trained and supervised by a parent.
4. Never allow adults to operate this machine without proper instruction.
5. Keep bystanders, helpers, pets, and children at least 75 feet from the machine while it is in operation. Stop machine if anyone enters the area.
6. Never run an engine indoors or in a poorly ventilated area. Engine exhaust contains carbon monoxide, an odortess and deadly gas.
7. Do not put hands or feet near rotating parts or in the feeding chambers and discharge opening. Contact with the rotating impeller can amputate fingers, hands, and feet.
8. Never attempt to unclog either the feed intake or discharge opening, remove or empty bag, or inspect and repair the machine while the engine is running. Shut the engine off and wait until all moving parts have come to a complete stop. Disconnect the spark plug wire and ground it against the engine.

NOTE:
The operator or user is responsible for accidents or hazards occurring to other people, their property, and themselves.

Product Specifications

Chipper/Shredder Model # Specifications

Component ldentification

If you are missing any parts, please complete the form on the next page and fax it back to us at:541-895-2756

Missing Parts Request Form

Please indicate the part that you are missing:

• Hardware beg ____
• Wheel Kit ____
•  Other ____
• Name ____
• Address ____
• Date of purchase ____
• Model#: ____
• EC0-19 ____
• Phone ____
• Email ____
• Serial ____

Comments:

IMPORTANT: Please include your receipt. Without a receipt, your order will be delayed. You may also email us at: customerservice@betstproducts.com. If emailing, please scan in your proof of purchase.

Safety Information

Your Responsibility
Restrict the use of this chipper/shredder to persons who read, understand and follow the warnings and instructions in this manual and on the machine.

Safety Information
Note: Not all safety labels shown may apply to your chipper/shredder

Preparation

1. Thoroughly inspect the area where the chipper/ shredder is to be used. Remove all rocks, bottles, cans, or other foreign objects which could be picked up or thrown and cause personal injury or damage to the machine.
2. Avoid discharging chipped material out of the discharge chute against a wall or on asphalt, concrete, or other hard surfaces as material being ejected could ricochet, causing injury to you or bystanders.
3. Always wear safety glasses or safety goggles to protect eyes during operation or while performing an adjustment or repair.
4. Wear sturdy, rough-soled work shoes and close fitting pants and shirts. Loose fitting clothing or jewelry can be caught in movable parts. Wear leather work gloves when feeding material in the chipper chute.
5. Before starting the engine, check bolts and screws for proper tightness to be sure the machine is in safe working condition. Also, visually inspect the chipper shredder at frequent intervals for any damage.
6. Maintain or replace safety and instructions labels, as necessary.
7. To avoid personal injury or property damage use extreme care in handling gasoline.
   • Use only an approved gasoline container.
   • Extinguish all cigarettes, cigars, pipes, and other sources of ignition.
   • Never fuel machine indoors.
   • Never remove gas cap or add fuel while the engine is hot or running.
   • Allow engine to cool at least two minutes before refueling.
   • Never over fill fuel tank. Leave at least 1/2 inch open below bottom of filler neck to provide space for fuel expansion.
   • Tighten gasoline cap securely.
   • If gasoline is spilled, wipe it off the engine and equipment. Move machine to another area and wait 5 minutes before starting the engine.
   • Never store machine or fuel container inside near an open flame, spark, or pilot light (e.g., furnace, water heater, space heater, clothes dryer, etc.}.
   • To reduce the fire hazard, keep machine free of grass, leaves, or other debris build-up. Clean up oil or fuel spills and remove any fuel soaked debris.
   • Allow machine to cool at least 5 minutes before storing.
8. Never attempt to make any adjustments while the engine (motor} is running (except where specifically recommended by the manufacturer}.

Safety Label Locations
These labels warn you of potential hazards that can cause serious injury. Read them carefully. If a label comes off or becomes hard to read, contact your PowRkraft for a replacement.

Safety Information
PowRkraft Outdoor Power products are designed to give safe and dependable service if operated according to instructions. Read and understand this owner’s manual before operating your power equipment.

Operator Responsibility
Know how to stop your power equipment quickly in case of emergency. Understand the use of all controls and connections. Be sure that anyone who operates this power equipment receives proper instruction. Do not let children operate the power equipment without parental supervision.

Operating Guidelines

READ THESE OPERATING GUIDELINES BEFORE YOU PROCEED ANY FURTHER

1. Do not put hands and feet near rotating parts or in the feeding chambers and discharge opening. Contact with the rotating impeller can amputate fingers, hands, and feet.

2. Before starting the machine, make sure the chipper chute, feed intake, and cutting chamber are empty and free of all debris.

3. Thoroughly inspect all material to be shredded and remove any metal, rocks, bottles, cans, or other foreign objects which could cause personal injury or damage to the machine.

4. If it becomes necessary to push material through the shredder hopper, use a small diameter stick. Do not use your hands or feet.

5. If the impeller strikes a foreign object or if your machine should start making an unusual noise or vibration, immediately shut the engine off. Allow the impeller to come to a complete stop. Disconnect the spark plug wire, ground it against the engine and perform the following steps:

   • Inspect for damage.
   • Repair or replace any damaged parts.
   • Check for any loose parts and tighten to assure continued safe operation.

6. Do not allow an accumulation of processed material tc build up in the discharge area. This can prevent prope discharge and result in kickback of material through the feed opening.

7. Do not attempt to shred or chip material larger than specified on the machine or in this manual. Personal injury or machine damage could result.
   The upper chute on the chipper/shredder is for Leaves and twigs only. Do not use the funnel for vines or long branches such as Weeping Willows as they may clog the flails.
   The lower chute is for longer and/or thicker pieces of yard waste. Depending on your model, you may cut up to a 3″ x 5″ in piece of wood.

8. Never attempt to unclog either the feed intake or discharge opening while the engine is running. Shut the engine off, wait until all moving parts have stopped, disconnect the spark plug wire and ground it against the engine before clearing debris.

9. Never operate without the shredder funnel, chipper chute, or discharge chute properly attached to the machine. Never empty or change discharge bag while the engine is running. Stop the engine when leaving the operating position.

10. Keep all guards, deflectors and safety devices in place and operating properly.

11. Keep your face and body back and to the side of the chipper chute while feeding material into the machine to avoid accidental kickback injuries.

12. Never operate this machine without good visibility or light.

13. Do not operate on a non-level surface.

14. Do not operate in a confined space.

15. Do not operate this machine while under the influence of alcohol or drugs.

16. Muffler and engine become hot and can cause a burn. Do not touch.

17. Never pick up or carry machine while the engine is running.

18. Do not leave this machine running while unattended

19. Keep children, bystanders, and pets 75 feet away.

20. Use only manufacturer approved accessories/ attachments.

Assembly Instructions

Required tools:
Approximate assembly time:

1. Remove the chipper from its carton.
   Remove staples, break glue on top flaps, or cut tape at carton end and peel along top flap to open carton.

2. Verify all parts are in the chipper carton.

   • Chipper Chute
   • Chipper engine and box assembly (pre-assembled)
   • Chipper Chute
   • Hardware Bag
   • Trailer hitch and funnel handles packaged together

Operating Instructions

DANGER
This machine was built to be operated according to the rules for safe operation in this manual. As with any type of power equipment, carelessness or error on the part of the operator can result in serious injury.

WARNING
Always wear hearing and eye protection while operating this machine or if you are within 75 feet of this machine.

Using the Chipper Shredder
Yard waste such as leaves and pine needles can be raked up and placed in the chipper funnel for shredding + DO NOT PUT BRANCHES INTO THE CHIPPER FUNNEL. BRANCHES SHOULD BE FED INTO THE SIDE CHIPPER CHUTE. When using the side chipper chute to chip branches, it is important to let the chipper feed the branches through automatically. DO NOT attempt to force the branches through. If the branches do not automatically feed through, gently push the branch and then allow the chipper to automatically feed the branch through. Forcing branches into the side chute may wear the belt prematurely.

Once material is shredded by the hammers on the impeller assembly, it is discharged through the open discharge chute or into the chipper bag.

Do not attempt to shred or chip any material other than normal yard vegetation found (i.e., branches, leaves, twigs, etc.) Avoid fibrous plants such as tomato vines until they are thoroughly dried. Twigs and small branches can be fed into the chipper chute. (See model specifications for maximum cutting thickness.)

IMPORTANT: The hammer screen is located inside the housing in the discharge area. If the screen becomes clogged, remove and clean as instructed. For best performance, it is also important to keep the chipper blade sharp.

Maintenance and Storage

Maintenance Schedule

WARNING Always stop engine, disconnect spark plug, and ground against engine before cleaning, lubricating or doing any kind of maintenance on your machine.

Maintenance and Storage

1. Never tamper with safety devices. Check their proper operation regularly.
2. Check bolts and screws for proper tightness at frequent intervals to keep the machine in safe working condition. Also, visually inspect machine for any damage and repair, if needed.
3. Before cleaning, repairing, or inspecting, stop the engine and make certain the impeller and all moving parts have stopped. Disconnect the spark plug wire and ground it against the engine to prevent unintended starting.
4. Do not change the engine governor settings or overspeed the engine. The governor controls the maximum safe operating speed of the engine.
5. Maintain or replace safety and instruction labels, as necessary.
6. Follow this manual for safe loading, unloading, transporting, and storage of this machine.
7. Never store the machine or fuel container inside where there is an open flame, spark or pilot light such as a water heater, furnace, clothes dryer, etc.
8. Always refer to the operator’s manual for proper instructions on off-season storage.
9. If the fuel tank has to be drained, do this outdoors. 10. Observe proper disposal laws and regulations for gas, oil, etc. to protect the environment.

If the Chipper Becomes Clogged:
If the discharge area becomes clogged:

• Stop the engine. Disconnect spark plug wire from spark plug and ground against the engine.
• Remove the large funnel and the clean out the access hatch on the side of the chipper engine box (as necessary).
• Reach in and clear the debris causing the blockage.
• Reinstall the funnel and the clean out access hatch.
• Connect the spark plug wire and restart

NOTE: If the blockage is severe, the hammer screen within the discharge chute can be removed as well, providing greater access. To accomplish this, remove the pins and slide the flail screen out of the discharge chute.

WARNING
Always stop engine, disconnect spark plug, and ground against engine before cleaning, lubricating or doing any kind of maintenance on your machine.

Removing and Sharpening the Blade
The chipper was shipped with one blade attached and one blade in the hardware bag. You can extend the belt life by operating the chipper with a sharp blade.

• Disconnect the PTO Shaft
• Remove the blade access hatch and rotate the blade to align with the access hatch.
• Remove the flail screen in the discharge chute by removing the pins that secure it at the top and bottom of the screen.
• Remove the blade using a 3/16″ Allen wrench on the outside of the blade and an adjustable wrench on the impeller assembly (through the discharge chute. Use a piece of pipe or wood to block the flails. preventing them from inadvertent.
• Add, replace or sharpen the blade as desired.
• When sharpening the blade, protect hands by using gloves and following the original angle of Grind. Torque to 250-300 in. Ibs.

NOTE: Make certain the blade is reassembled with the sharp edge facing upward.

Changing or Tightening the Belt
NOTE: The belt is designed to be the weakest link in the mechanical linkage between the engine and the blade. This improves the safety and durability of the chipper/ shredder.

Occasionally, changing or tightening the belt is required.
To change the belt:

• Stop the engine and make certain the chipper/ shredder has come to a complete stop. Disconnect the PTO Shaft from tractor.
• Remove the belt guard.
• Loosen engine mount bolts and release belt tension. Pry the belt off the pulley using a screw driver shaft as a wedge as you rotate the pulley. Place a new belt on the pulleys in a similar fashion.

Maintenance & Storage 

• Scribe a mark on the base plate along the edge of the engine. ” Remove the belt from the pulleys.
• Remove the handle, discharge chute and screen.
• Loosen the four bolts securing the engine. _ Slide the engine about 1/8″ further back.
• Tighten the engine mounting bolts securely.
• Re-install the belt and verify the tension.
• If the belt is still too loose, move the engine back another 1/8″ by repeating the above steps. & Reinstall guards, chutes, and screens.

Cleaning the Chipper/Shredder

• Make sure engine is off.
• Wipe off machine with an oiled rag to prevent rust.
• If the fuel tank has to be drained, do so outdoors.
• Observe proper disposal laws and regulations for gas, oil, etc., to protect the environment. Storing the Chipper/Shredder
• Clean the equipment thoroughly.
• Wipe equipment with an oiled rag to prevent rust.
• Refer to engine manual for correct engine storage instructions.
• Store unit in a clean, dry area. Do not store next to corrosive materials such as fertilizer.
• Never store the machine or fuel container inside where there is an open flame, spark or pilot light such as a water heater, furnace, clothes dryer, etc.

Troubleshooting

Service Dealer ….
Unit Does Not Discharge|

1. Discharge Chute is Clogged
2. Foreign Object lodged in Impeller
3. Low Engine RPM

|

1. Stop Tractor Engine Immediately & Disconnect PTO Shaft. Clean flail screen & Inside of Discharge Opening.
2. Stop Engine & Dosconnect Spark Plug Wire. Remove Lodged Object.
3.  Always Run Engine at 540 RPM PTO Speed

Rate of Discharge Slows|

1. Low Engine RPM
2. Chipper Blad Dull

|

1. Always Run Engine at Full Throttle
2. Replace Chipper Blade

PARTS BREAKDOWN

NOTE: This machine does not have wheels. It has stand legs.

Parts – Adjustable Stand

EC019.001 PARTS LIST

REF.| PART NUMBER| DESCRIPTION| | QTY.
1| LS18.101| HANDLE COVER| | 1
2| ECO19.101| DRAW BAR| | 1
3| DP8x60| LOCK PIN D8x60| | 1
4| GB6170-M12| NUT M12| | 4
5| LP12| LOCK PIN 12 •| | 2
6| T150.101| LOWER HITCH PIN| | 2
7| ECO19.011| MAIN FRAME,WDMT| | 1
8| GB5782-M10x90| BOLT M10x90| | 1
9| GB97.1-10| PLAIN WASHER 10| | 22
10| GB889.1-M 10| LOCK NUT M10| | 14
11| ECO19.102| CONNECTING ROD| | 1
12| ECO19.021| WHEEL,SET| | 2
13| DP12x60| LOCK PIN D12x60| | 2
14| GB5783-M8x20| BOLT M8x20 •| | 4
15| GB97.1-8| PLAIN WASHER 8| | 5
16| GB889.1-M8| LOCK NUT M8| | 5
17| ECO19.020| SHIELD.PULLEY| | 1
18| REACH 04-3360| CLAMPING COUPLING 3360 •| | 1
19| EFGC125.121| PULLEY| | 1
20| GB11544-SPB1295| V-BELT SPB1295| | 2
21| ECO19.105| CONNECTING PLATE| | 1
22| GB5783-M12x35| BOLT M12x35| | 4
23| GB93-12| LOCK WASHER 12| | 4
24| GB97.1-12| PLAIN WASHER 12| | 4
25| ECO19.012| MOUNTING BASE,GEARBOX| | 1
26| GB5782-M1 0x75| BOLT M10x75| | 10
27| TS50.300Z.02| GEARBOX,ASSY| | 1
28| ECO19.002| CHIPPER,ASSY| | 1
29| ECO19.016| DISCHARGE COVER| | 1
30| ECO19.106| DISCHARGE FLAP| | 1
31| ECO19.107| CLAMPING PLATE| | 3
32| JB4005-6×12| RIVET 6×12| | 6
33| GB5783-M1 0x25| BOLT M10x25| | 4

EC019.002 PARTS LIST

REF.| PART NUMBER| DESCRIPTION| | QTY.
1| REACH 04-3560| CLAMPING COUPLER 3560 •| | 1
2| ECO19.103| PULLEY| | 1
3| F90507| BEARING F90507,SET| | 2
4| GB889.1-M12| LOCK NUT M12| | 8
5| GB97.1-12| PLAIN WASHER 12| | 8
6| ECO19.003| ROTOR,ASSY| | 1
7| GB5783-M10x25| BOLT M10x25| | 4
8| GB93-10| LOCK WASHER 10| | 4
9| GB97.1-10| PLAIN WASHER 10| | 4
10| ECO19.019| PATCHING PLATE,WDMT| | 2
11| ECO19.013| HOUSING,WDMT| | 1
12| R PIN 3.2| R PIN 3.2| | 2
13| ECO19.017| SIFTING PLATE,WDMT| | 1
14| ECO19.018| SIFTING PLATE,WDMT| | 1
15| ECO19.109| SUPPORTING ROD| | 2
16| ECO19.022| COVER,BEARING| | 1
17| GB5783-M1 0x25| BOLT M10x25| | 4
18| GB93-10| LOCK WASHER 10| | 4
19| GB97.1-10| PLAIN WASHER 10| | 4
20| ECO19.015| UPPER HOPPER| | 1
21| ECO19.111| ENTRANCE FLAP,UPPER| | 1
22| ECO19.112| CLAMPING PLATE| | 2
23| JB4005-6×12| RIVET 6×12| | 6
24| ECO19.110| ENTRANCE FLAP,LOWER| | 1
25| ECO19.014| LOWER HOPPER| | 1
26| GB889.1-M8| LOCK NUT MS| | 3
27| GB97.1-8| PLAIN WASHER 8| | 3

EC019.003 PARTS LIST

REF.| PART NUMBER| DESCRIPTION| | QTY.
1| ECO19.023| ROTOR,WDMT| | 1
2| ECO19.114| SPACER| | 2
3| GB2673-M8x30| COUNTERSUNK SCREW M8x:| | 6
4| ECO19.115| KNIFE| | 2
5| GB97.1-8| PLAIN WASHER 8| | 3
6| GB889.1-M8| LOCK NUT M8| | 3
7| ECO19.024| SHAFT HOLDER,WDMT| | 8
8| ECO19.120| SHORT SPACER| | 16
9| GB879-5×35| SPRING PIN 5×35| | 3
10| ECO19.116| SHAFT| | 3
11| ECO19.119| LONG SPACER| | 16
12| ECO19.117| FLAIL KNIFE| | 24
13| GB893.1-16| RETAINING RING 16| | 3
14| GB1096-A8x7x328| KEY A8x7x328| | 1
15| ECO19.113| MAIN SHAFT| | 1
16| ECO19.118| PLATE| | 1

Parts Request Form
E-mail cservice@betstco.com

• Name: —————-
• Address: —————-
• Model Number: —————–
• City State Zip:  —————-
• Serial Number: —————-
• Phone: —————-
• Purchased From:———-
• Purchase Date: —————-
• E-mail: —————-

FARMER-HELPER Limited Warranty

Unless otherwise stated on purchase invoice, Betstco warrants to original Purchaser that Farmer-Helper products are free from major defects in material under normal use and service for a period of 90 Days from the date the product is purchased or shipped, whichever is later. Commercial use 90 days. Use at address that is not yours, is considered commercial use. Consumable, Expendable, Wear Items (Rubber plastic parts, hydraulic hoses, belts, tires, cables, blades, tines, wedges, teeth, tips, chains, pins, brushes, filters, etc) and cracked hydraulic pumps, bent or broken cylinder rods are not covered under this warranty. Warranty does not cover items that have been modified, damaged by abuse or usage not in accordance with design or maintenance.
Betstco obligation under this warranty is to repair or replace defective upon approval by; Betstco, 83371 Melton Rd. N, Creswell OR 97426 that Warranty Claim is valid. Product shall be returned upon request of Betstco. Transportation charges to be prepaid by user.
Gasoline or diesel engines used to powered Farmer-Helper products are covered by the warranty of the appropriate engine manufacture an Purchaser must look to the engine manufacture for all issues
relasing to engine operation.
Betstco assumes no responsibility for outside labor.
PERMISSABLE BY APPLICABLE LAW, BETSTCO HEREBY DISCLAIMS ALL WARRANTIES OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, ANY IMPLIED WARRANTIES WITH RESPECT TO THE PRODUCT PURCHASED, WITHOUT LIMITING THE GENERALITY OF THE FOREGOING, BETSTCO
HEREBY EXPRESSLY DISCLAIMS ALL LIABILITY FOR PRODUCT DEFECT OR FAILURE, CLAIMS THAT ARE DUE TO NORMAL WEAR, PRODUCT MISUSE, ABUSE, PRODUCT MODIFICATION, IMPROPER PROD-
UCT SELECTION, NON-COMPLIANCE WITH ANY CODES, OR MISAPPROPRIATION. BETSTCO MAKES
NO WARRANTIES TO THOSE DEFINED AS “CONSUMERS” IN THE MAGNUSON-MOSS WARRANTY FEDERAL TRADE COMMISION IMPROVEMENTS ACT. THE FOREGOING EXCLUSION OF IMPLIED WARRANTIES DO NOT APPLY TO THE EXTENT PROHIBITED BY LAW. PLEASE REFER TO YOUR LOCAL LAWS FOR ANY SUCH PROHIBITIONS.
THERE SHALL BE NO LIABILITY FOR PRODUCT LIABILITY OR LIABILITY ON THE PART OF BETSTCO FOR ANY GENERAL SPECIAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE SALE OR USE OF ANY PRODUCTS SOLD BY BETSTCO OR AN AGENT THEREOF, BETSTCO MAKES NO WARRANTIES, EXPRESS OR IMPLIED, (INCLUDING, BUT NOT LIMITED TO, ANY WARRANTY OF MERCHANTABILITY OR
FITNESS OF THE PRODUCTS FOR ANY PURPOSE) WITH RESPECT TO THE PRODUCTS COVERED BY
THIS AGREEMENT EXCEPT AS IN THIS PARAGRAPH OTHERWISE EXPRESSLY PROVIDED.
THIS IS THE SOLE AND ONLY WARRANTY OF VALUE-LEADER PRODUCTS, NO OTHER WARRANTY IS APPLICABLE, EITHE EXPRESSED OR IMPLIED, IN FACT BY LAW.
This warranty shall not be interpreted to render Bitstock, or any authorized agent liable for injury or damages of any kind or
nature, direct, consequential, or contingent, to a person or property.
The sole and only remedy in regard to any defective product shall be the repair or replacement thereof as herein provided, Bitstock, agent(s) of Betstco shall not be liable for any consequential, special, incidental or punitive damages resulting from or
caused by any such defects
Betstco reserves the rights to make improvements in design or changes in specifacations at any time, without incurring any obligations to owners of the units previously sold.

WARRANTY VOID IF REGISTRATION IS NOT RECEIVED OR RECORDED ONLINE WITHIN 30 DAYS OF PURCHASE DATE OR SHIP DATE, WHICHEVER IS LATER.

• ITEM:  MODEL#
• PURCHASE DATE:
• PURCHASED FROM:
• GIFT INV# ORDER#
• OWNER NAME:
• SERIAL #
• OWNER ADDRESS:
• CITY:
• COUNTY:
• ST:
• ZIP:
• PHONE:
• EMAIL:

ACCEPTANCE OF RESPONSIBILITY:
I (PURCHASER) HAVE READ OPERATORS MANUAL AND LIMITED WARRANTY OR SOMEONE HAS READ/AND EXPLAINED ALL INSTRUCTIONS TO ME. I UNDERSTAND THIS WARRANTY DOES NOT COVER ANY LABOR AND THAT ALL DISPUTES WILL BE SETTLED BY BINDING ARBITRATION. BIND-ING ARBITRATION IS CONDUCTED BY THE BETTER BUSINESS BUREAU (BBB) LOCATED AT 4004 SW KRUSE WAY PLACE ST 375 LAKE OSWEGO OR 97035 OR THE CURRENT BBB LOCATION CLOS-EST TO BETSTCO. I ACKNOWLEDGE MY LIMITED WARRANTY IS VOID IF ANY ATTEMPT TO REPAIR OR REPLACE DEFECTIVE PARTS HAS BEEN MADE BY UNAUTHORIZED PERSONNEL.I ACKNOWL-EDGE RECEIPT OF MY OPERATORS MANUAL AND HAVE READ THE SAFE OPERATION SECTION. I ACKNOWLEDGE UNDERSTANDING MAINTENANCE AND SAFE OPERATION REQUIREMENTS, ITEM SPECIFACATIONS, OPERATION, CONTROLS AND STORAGE REQUIRMENTS. I UNDERSTAND THAT
IS ALONE AM RESPONSIBLE FOR PROPER MAINTENANCE, CARE AND SAFE OPERATIONOF THIS FARMER-HELPER ITEM
I (PURCHASER) AGREE THAT PERSONS NOT FAMILIAR WITH THE OPERATION OF THIS ITEM SHOULD NOT BE ALLOWED TO USE IT. CHILDREN ESPECIALLY SHOULD NOT OPERATE OR BE NEAR POWER PRODUCTS WHEN IN USE. ANYONE OPERATING VALUE-LEADER PRODUCTS SHOULD HAVE READ OPERATIONS MANUALS AND SAFTEY MANUALS.

• OWNERS SIGNATURE: x
• DATE:

YOU MUST SIGN THIS WARRANTY AND MAIL OR FAX A COPY TO BETSTCO, 83371 MELTON RD, CRESWELL OR, 97426. IF YOU PREFER YOU MAY COMPLETE YOUR REGISTRATION ONLINE AT WWW.VALUE-LEADER.COM. THIS WARRANTY IS NOT EFFECTIVE UNLESS PURCHASER COMPLETE REGISTRATION AND WARRANTY FOR WITHIN 30 DAYS OF PURCHASE OR SHIP DATE WHICHEVER IS LATER.

NOTE: WE MAY REFUSE WARRANTY OF ANY KIND UNLESS BETSTCO, RECEIVES A COMPLETED, LEGIBLE AND SIGNED WARRANTY REGISTRATION. IT IS THE RESPONSIBILITY OF THE PURCHASER TO ASSURE THAT REGISTRATION DOCUMENT IS RECIEVED BY  1 YEAR EXTENDED WARRANTY & REGISTRATION
FARMER-HELPER IMPLEMENTS BRANDED PRODUCTS

1 YEAR EXTENDED WARRANTY
1 Year Extended Warranty amends to original Recorded Warranty Registration the time period of described coverage. Extended Warranty does not apply to consumable and Expendable Item as described in Product Warranty Registration.
This amendment does not affect any other part of recorded Warranty Registration or policy.
No one is authorized to alter, modify, or enlarge this Amendment to original recorded Warranty Registration
EXTENDED REGISTRATION & PAYMENT MUST BE RECEIVED WITHIN 30 DAYS OF PURCHASE DATE EXTENDED WARRANTY REGISTRATION

• PRODUCT & MODEL #
• SERIAL #
• OWNER NAME :
• BETSTCO INVOICE #

ACCEPTANCE OF RESPONSIBILITY:
I (PURCHASER) HAVE READ AND UNDERSTAND THE EXTENDED WARRANTY OR SOMEONE HAS READ AND EXPLAINED ALL THE ABOVE TO ME. I UNDERSTAND THIS EXTENDED WARRANTY DOES NOT COVER ANY LABOR. I HAVE FILED MY ORIGINAL WARRANTY REGISTRATION AND FULLY UNDERSTAND MY REQUIREMENTS. I UNDERSTAND THAT I ALONE AM RESPONSIBLE FOR PROPER MAINTENANCE, CARE AND SAFE OPERATION OF THIS TRACTOR IMPLEMENT.

• OWNERS SIGNATURE: x
• DATE:
• FAX TO 1-541-895-2756

YOU MUST SIGN THIS WARRANTY AND MAIL OR FAX A COPY TO BETSTCO, 83371 MELTON RD, CRESWELL OR. IF YOU PREFER YOU MAY COMPLETE YOUR REGISTRATION ONLINE AT WWW.VALUE-LEADER.COM. THIS WARRANTY IS NOT EFFECTIVE UNLESS PURCHASER COMPLETE REGISTRATION AND WARRANTY FOR WITHIN 30 DAYS OF PURCHASE OR SHIP DATE WHICHEVER IS LATER.
NOTE: WE MAY REFUSE WARRANTY OF ANY KIND UNLESS BETSTCO, RECEIVES A COMPLETED, LEGIBLE AND SIGNED WARRANTY REGISTRATION. IT IS THE RESPONSIBILITY OF THE PURCHASER TO ASSURE THAT REGISTRATION DOCUMENT IS RECIEVED BY BETSTCO.

References

• Betstco Tractor Impliments
• 541-895-3083 M-F, 7am-4pm PST" class="nturl" > Value-Leader – Sales, Suport, and Service 541-895-3083 M-F, 7am-4pm PST

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>