Denver ECQ 106 Alarm clock with Wireless Charging Instruction Manual
- June 10, 2024
- Denver
Table of Contents
Denver ECQ 106 Alarm clock with Wireless Charging
Product Information
This product is a multi-functional alarm clock that features wireless charging
capabilities. It has a backup system and is designed to operate with an AC/DC
adaptor. The product has various
controls, including a wireless charging pad, time, hour, minute,
dimmer/snooze, two alarm buttons (AL 1 and AL 2), alarm off (AL OFF), PM
indicator, alarm 1 indicator, alarm 2 indicator, wireless charging indicator,
DC IN, buzzer, and battery compartment. The unit can be set to a 12H or 24H
hour format. The alarm volume can be set to high or low.
Product Usage Instructions
-
Before using the product for the first time, read the safety instructions carefully and keep them for future reference.
-
Keep the product out of reach of children and pets to avoid chewing and swallowing.
-
Ensure that the product is not used as a toy.
-
The operating and storage temperature of the product is from 0 degree Celsius to 40 degree Celsius.
-
Insert the small plug of the AC/DC adaptor into the DC jack and then insert the adaptor into any convenient household outlet having AC 100-240V 50/60Hz to power on the unit. To set the time, press and hold the TIME button for 2 seconds to enter the clock setting mode. Use the HOUR and MIN buttons to
select the hour format and set the hour and minute. Press the TIME button to confirm. -
To set alarm 1, press and hold the AL 1 button for 2 seconds to enter the alarm 1 time setting mode. Use the HOUR and MIN buttons to set the hour and minute. Use the HOUR or MIN button to select the volume level (high or low). Press the AL 1 button to confirm Press the AL 1 button again to turn on the alarm 1 function.
-
To set alarm 2, press and hold the AL 2 button for 2 seconds to enter the alarm 2 time setting mode. Use the HOUR and MIN buttons to set the hour and minute. Use the HOUR or MIN button to select the volume level (high or low). Press the AL 2 button to confirm.
Press the AL 2 button again to turn on the alarm 2 function. -
To turn on or off an alarm, press the corresponding AL 1 or AL 2 button when the display shows clock time. The corresponding alarm
indicator will be on when the alarm is enabled. -
To temporarily deactivate an alarm, press the DIMMER/SNOOZE button. The snooze function will delay the alarm for 9 minutes.
After 9 minutes, the alarm will sound again. To cancel the snooze and alarm, press the AL OFF button. -
To stop the alarm when it goes off, press the AL OFF button. The alarm indicator will still stay on and the alarm will go off the next day at the same time unless it is turned off.
Safety information
Please read the safety instructions carefully before using the product for the first time and keep the instructions for future reference.
- This product is not a toy. Keep it out of reach of children.
- Keep product out of the reach of children and pets to avoid chewing and swallowing.
- Product operating and storage temperature is from 0 degree Celsius to 40 degree Celsius. Under and over this temperature might affect the function.
- Never open the product. Touching the inside electrics can cause electric shock. Repairs or service should only be performed by qualified personnel.
- Do not expose to heat, water, moisture, direct sunlight!
- Please protect your ears against loud volume. Loud volume can damage your ears and risk in hearing loss.
- The unit is not waterproof. If water or foreign objects enter the unit, it may result in fire or electric shock. If water or a foreign object enters the unit, stop use immediately.
- Only use with supplied Adaptor. The direct plug-in adapter is used as disconnect device, the disconnect device shall remain readily operable. So, make sure there is space around the power outlet for easy access.
- Do not use non original accessories together with the product as this can make the product functionality abnormal.
- Never use old and new batteries or different types of batteries together. Remove the batteries when you are not using the system for a longer period of time. Check the polarity (+/-) of the batteries when inserting them in the product. Wrong positioning can cause an explosion. Batteries are not included.
LOCATION OF CONTROLS
- Wireless charging pad
- TIME
- HOUR
- MINUTE (MIN)
- DIMMER/SNOOZE
- ALARM 1 (AL 1)
- ALARM 2 (AL 2)
- ALARM OFF (AL OFF)
- PM indicator
- Alarm 1 indicator
- Alarm 2 indicator
- Wireless charging indicator
- DC IN
- BUZZER
- Battery compartment
Unit Power Supply
This unit is designed to operate with AC/DC adaptor.
Operation with AC/DC adaptor
Insert the small plug of adaptor into the DC jack.
Insert the AC/DC adaptor into any convenient household outlet having AC
100-240V 50/60Hz.
The display will be illuminated, indicating that it is powered on.
BACKUP SYSTEM
- The unit is equipped with a backup system. It requires 2 ‘AAA’ size batteries. Insert the batteries into the battery compartment and make sure the positive and negative (+ or -) ends of the batteries are in contact with the corresponding terminals in the battery compartment.
- In the event of power failure or disconnection of the power cord, the power supply is automatically switched to the backup battery, keeping the time and alarm settings.
- To open the battery compartment, press the battery cover from the side and pull it.
- When replacing the battery, do not disconnect the power adaptor. Otherwise, all clock and alarm settings will be lost.
SETTING TIME
- Press and hold the TIME button for 2 seconds to enter the clock setting mode.
- Press the HOUR or MIN button to select 12H or 24H hour format. Press the TIME button to confirm.
- Press the HOUR button to set the hour and MIN button to set the minute. Press the TIME button to confirm.
SETTING THE ALARM 1
- Press and hold the AL 1 button for 2 seconds to enter the alarm 1 time setting mode.
- Press HOUR to set the hour and MIN button to set the minute. Then press the AL 1 button to confirm.
- Press HOUR or MIN button to select h or n. (Note: h—–buzzer volume is high, n—–buzzer volume is low.)
- Press the AL 1 button to confirm.
- Press the AL 1 button to turn on the alarm 1 function till the alarm 1 indicator appears on LED display.
Note :
SETTING THE ALARM 2
- Press and hold the AL 2 button for 2 seconds to enter the alarm 2 time setting mode.
- Press HOUR to set the hour and MIN button to set the minute. Then press the AL 2 button to confirm.
- Press HOUR or MIN button to select h or n. (Note: h—–buzzer volume is high, n—–buzzer volume is low.)
- Press the AL 2 button to confirm.
- Press the AL 2 button to turn on the alarm 2 function till the alarm 2 indicator appears on LED display.
Note: The buzzer is located at the bottom of the unit, make sure that nothing will cover the buzzer while using the alarm function.
TURNING THE ALARMS ON OR OFF
When the display shows clock time, press AL 1 or AL 2 button to enable or
disable the respective alarm. The corresponding Alarm 1 or Alarm 2 indicator
will be on when the alarm is enabled.
SNOOZE
- When the alarm goes off, the corresponding Alarm 1 or Alarm 2 indicator will flash on the display.
- Press the DIMMER/SNOOZE button to temporarily deactivate it. The snooze function will delay your alarm for 9 minutes. After 9 minutes, the alarm sounds again.
- The corresponding Alarm 1 or Alarm 2 indicator will flash on the display during the snooze period.
- To cancel the snooze and the alarm, press AL OFF button.
TO STOP THE ALARM WHEN ALARM GOES OFF
- Press AL OFF button to stop the alarm.
- Alarm indicator will still stay on and the alarm will go off the next day at a preset time.
TO DISABLE THE ALARM
- Press AL 1 button repeatedly to disable Alarm 1 while the alarm is not going off. Press AL 2 button repeatedly to disable Alarm 2 while the alarm is not going off.
- Corresponding alarm indicator will be off and the alarm will not go off until you enable it again.
DISPLAY DIMMER
- Press the DIMMER/SNOOZE button to change the brightness level of the display: 100% > 75% > 50% > 25% > Off.
- Default setting of the brightness level is “100%”.
QI WIRELESS CHARGING
-
Place your Qi enabled smartphone on the center of the wireless charging pad.
-
Please check if your phone screen shows charging status.
If your phone is not charging:- Check if your device supports Qi wireless charging
- Place mobile device in the center
- Remove the phone case which contains magnet/metal material or is thicker than 0.12’’ (3mm)
-
Charges through most cases of PC or TPU material up to 0.12’’ (3mm) thick.
-
Compatible devices (Qi Wireless Charging Pad) iPhone 13/13Pro, iPhone 12/12Pro, iPhone 11/11Pro, iPhone X, iPhone 8/8 Plus, Samsung Galaxy Note 8/5, Galaxy S9/S9+/S8/S8+, S7/S7 Edge, S6 Edge+, S6/S6 Edge, LG V30, Nexus 7/6/5, other Qi-enabled smartphones/tablets and accessories.
Note: The Wireless charging indicator will be on while the unit is charging.
Please notice – All products are subject to change without any notice. We take reservations for errors and omissions in the manual.
**ALL RIGHTS, COPYRIGHT DENVER A/S
**
Electric and electronic equipment contains materials, components and
substances that can be hazardous to your health and the environment, if the
waste material (discarded electric and electronic equipment) is not handled
correctly.
Electric and electronic equipment is marked with the crossed out trash can
symbol, seen above. This symbol signifies that electric and electronic
equipment should not be disposed of with other household waste, but should be
disposed of separately.
All cities have established collection points, where electric and electronic
equipment can either be submitted free of charge at recycling stations and
other collection sites, or be collected from the households. Additional
information is available at the technical department of your city.
Hereby, Denver A/S declares that the radio equipment type ECQ-106 is in
compliance with Directive 2014/53/EU. The full text of the EU declaration of
conformity is available at the following internet address: denver.eu and then
click the search ICON on topline of website. Write model number: ECQ-106. Now
enter product page, and RED directive is found under downloads/other
downloads.
Max Output Power: 9W
Denver A/S
Omega 5A, Soeften
DK-8382 Hinnerup
Denmark
www.facebook.com/denver.eu
Contact
Nordics
- Headquarter
- Denver A/S
- Omega 5A, Soeften
- DK-8382 Hinnerup
- Denmark
- Phone +45 86 22 51 00
- (Push “2” for support)
E-Mail
For technical questions, please write to:
support.hq@denver.eu
For all other questions please write to:
contact.hq@denver.eu
Germany
- Denver Germany GmbH Service Gutenbergstrasse 1 94036 Passau
- Phone: +49 851 379 369 40
- E-Mail support.de@denver.eu
- Fairfixx GmbH
- Repair and service
- Rudolf-Diesel-Str. 3 TOR 2
- 53859 Niederkassel
- (for TV, E-Mobility/Hoverboards/Balanceboards, Smartphones & Tablets)
- Phone: +49 851 379 369 69
Austria
- Lurf Premium Service GmbH Deutschstrasse 1 1230 Wien
- Phone +43 1 904 3085
- E-Mail denver@lurfservice.at
Benelux/France
- Denver Benelux BV Barwoutswaarder 13C+D 3449 HE Woerden
- The Netherlands
- Phone +31 348 420 029
- E-Mail support-nl@denver.eu
Spain
- Denver Spain S.A.
- C/ Moscú, 1 Pol.Ind.Mas de Tous 46185 La Pobla de Vallbona
- Valencia (Spain)
- Phone +34 960 046 883
- Mail serviciotecnico.denver@denver.eu
Portugal
Phone +35 1255 240 294
E-Mail denver.service@satfiel.com
If your country is not listed above, please write an email to
support@denver.eu
Denver A/S
Omega 5A, Soeften DK-8382 Hinnerup Denmark
denver.eu
facebook.com/denver.eu