De Longhi ECAM46.86X Bean to Cup Espresso and Cappuccino Machine Instructions

ECAM46.86X Bean to Cup Espresso and Cappuccino Machine
Instructions

ECAM46.86X
BEAN TO CUP ESPRESSO AND
CAPPUCCINO MACHINE
Instructions for Use
Instructions videos available at:
http://ECAM46080.delonghi.com

ECAM46.86X Bean to Cup Espresso and Cappuccino Machine

Before using the appliance, always read the safety warnings.

INTRODUCTION

Thank you for choosing this bean to cup espresso and cappuccino machine. We hope you enjoy using your new appliance.  Take a few minutes to read this Instruction for Use.
This will avoid all risks and damage to the appliance.
1.1 Letters in brackets
The letters in brackets refer to the legend in the description of the appliance on pages 2-3.
1.2 Troubleshooting and repairs
In the event of problems, first try and resolve them by reading the information given in sections “16. Displayed messages” and “17. Troubleshooting”.
If this does not resolve the problem or you require further information, you should consult customer services by calling the number given on the annexed “Customer Service” sheet.
If your country is not among those listed on the sheet, call the number given in the guarantee. If repairs are required, contact De’Longhi customer services only. The addresses are given in the guarantee certificate provided with the machine.

DESCRIPTION

2.1 Description of the appliance (page 3 – A )
A1. Beans container lid
A2. Pre-ground coffee funnel lid
A3. Beans container
A4. Pre-ground coffee funnel
A5. Grinding adjustment dial
A6. Cup shelf
A7. ON/STANDBY button
A8. Power cord
A9. Coffee spouts (adjustable height)
A10. Hot water and steam connection nozzle
A11. Infuser door
A12. Infuser
A13. Water tank lid
A14. Water tank
A15. Water softener filter compartment
A16. Condensate tray
A17. Coffee grounds container
A18. Cup tray
A19. Drip tray
A20. Drip tray water level indicator
2.2 Description of touch screen (page 2 – B )
B1. Display
B2. : Appliance settings menu / press to exit the menu
B3. : To customise beverages / scroll arrow
Directly selected beverages:

B10. : Scroll arrow / Beverage selection menu (other than directly selected beverages):

• 2 Espresso
• Ristretto
• 2 Ristretto
• Espresso lungo
• 2 Espresso Lungo| • Doppio+
• Caffelatte
• Hot Water
• Flat White
• Cappuccino Mix
---|---

B11. : To confirm the selection / Aroma selection
Please note: A light touch is enough to activate the icon.
2.3 Description of the accessories (page 2 – C )
C1. “Total Hardness Test” indicator paper
C2. Pre-ground coffee measure
C3. Descaler
C4. Water softener filter (if present)
C5. Cleaning brush
C6. Hot water spout
2.4 Description of the milk container (page 2 – D )
D1. Froth adjustment and CLEAN dial
D2. Lid with milk frother
D3. Frothed milk spout
D4. Milk intake tube
D5. Milk container

SETTING UP THE APPLIANCE

Please note:

• The first time you use the appliance, rinse with hot water all removable accessories which may come into contact with water or milk.
• The first time you use the machine, the water circuit is empty and the appliance could be very noisy.The noise becomes less as the circuit fills.
• Coffee has been used to factory test the appliance and it is therefore completely normal for there to be traces of coffee in the mill. The machine is, however, guaranteed to be new.

1. Connect the appliance to a mains socket (fig. 1);

2. Language”: press the scroll arrows (B3) or   (B10) until the required language is displayed, then press (B11) to confirm.
   Follow the instructions indicated on the appliance display:

3. Remove the water tank (A14) (fig. 2), fill to the MAX line (marked on the tank) with fresh water (fig. 3), then put the tank back in the appliance (fig. 4);

4. Check that the hot water spout (C6) is inserted on the connection nozzle (A10) (fig. 5) and place a container holding a minimum of 100 ml underneath (fig. 6);
   

5. Press (B11)to confirm. The appliance delivers water  from the water spout then goes off automatically.

The coffee machine is now ready for normal use.
Please note:

• The first time you use the appliance, you need to make 4 – 5 cappuccinos before it starts to give satisfactory results.
• To enjoy your coffee even more and improve the performance of your appliance, we recommend installing a water softener filter (C4) as described in section “14. Water softener filter”. If your model is not provided with a filter, you can request one from De’Longhi Customer Services.

TURNING THE APPLIANCE ON

Please note:
Each time the appliance is turned on, it performs an automatic preheat and rinse cycle which cannot be interrupted. The appliance is ready for use only after completion of this cycle.
Danger of burns!
During rinsing, a little hot water comes out of the coffee spouts (A9) and is collected in the drip tray (A19) underneath. Avoid contact with splashes of water.

• To turn the appliance on, press the button  (A7) (fig. 7).
• After heating, the appliance automatically performs a rinse cycle. As well as heating the boiler, this also heats the internal circuits by circulating hot water.

The appliance is ready for use when the main screen appears.

TURNING THE APPLIANCE OFF

Whenever the coffee machine is turned off after being used to make coffee, it performs an automatic rinse cycle.

1. To turn the appliance off, press the button (A7) (fig.7).
2. If provided for, the appliance performs a rinse cycle then goes off (stand-by).

Please note:
If you will not be using the appliance for some time, unplug from the mains socket:

1. First turn the appliance off by pressing the button  (A7) (fig. 7);
2. Disconnect the appliance by unplugging it from the mains socket.

Important!
Never unplug while the appliance is on.

MENU SETTINGS

The menu has 5 items, some divided into subgroups:

• Rinsing;

• Language;

• Maintenance:
  – Descale,
  – Install filter,
  – (if a filter has been installed): Replace filter,
  – (if a filter has been installed): Remove filter

• General:
  – Set temperature,
  – Water hardness,
  – Auto-off,
  – Energy saving,
  – Beep,
  – Default beverages,
  – Default values;

• Statistics.

6.1 Rinsing
Use this function to deliver hot water from the coffee spouts (A9) and hot water spout (C6), if inserted, to clean and heat the appliance’s internal circuit.

1. Place a container with a minimum capacity of 200ml under the coffee and hot water spouts (fig. 6);
2. Press (B2) to enter the menu;
3. Press the scroll arrows   (B3) or (B10) until the  required item is displayed;
4. Press (B11): after a few seconds, hot water is delivered first from the coffee spouts, then from the hot water spout (if inserted) to clean and heat the appliance’s internal circuit;
5. To stop rinsing, press or wait for rinsing to stop  automatically.

Please note:

• If the appliance is not used for more than 3-4 days, when you turn it on again, we strongly recommend performing 2/3 rinses before use;
• After cleaning, it is normal for the grounds container (A17)  to contain water.

6.2 Language
To modify the language of the display (D5), proceed as follows:

1. Press (B2) to enter the menu;
2. Press the scroll arrows (B3) or (B10) until the  required item is displayed;
3. Press (B11);
4. Press the scroll arrows (B3) or (B10) until the  required language is displayed;
5. Press (B11): The appliance goes back to the menu;
6. Then press (B2) to exit the menu.

6.3 Maintenance
Here you can find all the maintenance operations required by the appliance over time:

• Descaling: For instructions on descaling, see section “12. Descale”.
• I nstall filter/Replace filter/Remove filter: For instructions on how to install/replace/remove the filter (C4), see section “14. Water softener filter”.

6.4 General
Here you can find the settings to customise the basic functions of the appliance:

1. Press (B2) to enter the menu;

2. Press the scroll arrows  (B3) or (B10) until  “General” is displayed;

3. Press (B11) to confirm;

4. Press the scroll arrows or until the required item is displayed:
   Set temperature:
   To change the temperature of the water used to make the coffee, proceed as follows:
   • Press (B11). The current value appears on the dis- play (D5) and the “New” value flashes;
   • Select the new value you want to set using the scroll arrows (B3) or (B2);

5. When the required value (low, medium, high) has been selected, press .
   The display goes back to the previous screen.

Please note:
Varying the temperature has most effect for long beverages.
Water hardness
For instructions on identifying and setting water hardness, see  section “16. Setting water hardness”.
Auto-off (standby):
Auto-off can be set so that the appliance goes off after 15 or 30 minutes, or 1, 2 or 3 hours

• Press (B11). The current value appears on the dis- play (B1) and the “New” value flashes;
• Select the new value you want to set using the scroll arrows (B3) or (B10);
• When the required value (15 min, 30 min, 1 hour, 2 or 3 hours) has been selected, press .

The display goes back to the previous screen.
Energy saving:
To disable or enable “Energy Saving”, proceed as follows:

• Press (B11). The current state (“Enabled” or “Disabled”) and the operation to be performed (“Disable?” or “Enable?”) by confirming with appear on the display (D5);
• Press to disable or enable the function.

The display goes back to the previous screen.
Please note:

• when the function is enabled, the “ECO” symbol appears on the display.
• When in energy saving mode, a few seconds elapse before the first coffee, cappuccino or milk-based coffee is delivered as the appliance must heat up again.
• If the milk container (D) is inserted, “Energy Saving” has no effect.

Beep:
Use this function to enable or disable the beep. Proceed as follows:

• Press (B11). The current state (“Enabled” or “Disabled”) and the operation to be performed (“Disable?” or “Enable?”) by confirming with appear on the display (D5);
• Press to disable or enable the function.

The display goes back to the previous screen.
Default beverages
Use this function to reset the default values for all the beverages, or the individual previously customised beverages.

• Press (B11). The previously customised beverages  and “All” appear on the display (D5);
• Select “All” to reset the aroma and quantity settings of all beverages to the default values, or select the required beverage, then press ;
• To reset the default values, press .
• The appliance confirms the reset and goes back to the previous screen.

Reset another beverage or press (B2) to exit the menu.
Default values:
Use this function to reset all the appliance and beverage settings (apart from the language which remains as selected the first time the appliance was used).
4. Press (B11);
5. Press to reset all the settings;
6. The appliance confirms the reset and goes back to the previous screen.
Press (B2) to exit the menu.

6.5 Statistics
This displays statistics relating to the machine. To view the statistics,proceed as follows:

1. Press (B2) to enter the menu;
2. Press the scroll arrows (B3) or (B10) until  “Statistics” is displayed;
3. Press (B11): statistics on the appliance appear on  the display (D5), use the scroll arrows or to  scroll through the items;
4. Then press to exit.

To go back to the main screen, press again.

MAKING COFFEE

7.1 Temporarily varying the coffee aroma
To temporarily vary the aroma of the coffee in the automatic recipes, press (B11):

Please note:

• The variation in aroma is not saved and the next time a beverage is delivered automatically, the appliance selects the default value ( my).
• If a few seconds elapse between temporary customising of the aroma and delivery of the beverage, the aroma returns to the default value ( my).

7.2 Making automatic recipes using coffee beans
Important!
Do not use green, caramelised or candied coffee beans as they could stick to the coffee mill and make it unusable.

1.  Fill the container (A3) with coffee beans (fig. 8);
   

2. Place under the coffee spouts (A9):
   – 1 cup if you want 1 coffee;
   – 2 cups, if you want to make 2 coffees (see note at end of section).

3. Lower the spouts as near as possible to the cup. This makes a creamier coffee (fig. 9);

4. Then select your required coffee:

Directly selected beverages

Coffees selectable from (B10) and confirming with (B 1)
Ristretto| ≃ 30 ml| from ≃ 20to ≃40m1|
Espresso lungo| ≃ 120 ml| from ≃80to ≃180m1|
Doppio+| ≃ 120m1| from ≃80 to ≃180m1| +
2 Espresso| ≃ 40 ml x 2 cups| —|
2 Espresso Lungo| ≃ 120 ml x 2 cups| —|
2 Ristretto| ≃30 ml x 2 cups| —|

5. Preparation begins. The selected beverage appears on the display (D5) together with a progress bar which gradually fills as preparation proceeds.
Please note:

• You can prepare 2 cups of ESPRESSO, RISTRETTO or ESPRESSO LUNGO coffee at the same time by pressing “X2” (B10) during preparation of single beverages (the message is displayed for a few seconds at the start of preparation).
• While the machine is making coffee, delivery can be interrupted at any moment by pressing “STOP” – (B3) or (B2).
• At the end of delivery, to increase the quantity of coffee in the cup, just press “EXTRA” – within 3 seconds. When the required quantity is reached, press “STOP”- (B3).

Once the coffee has been made, the appliance is ready to make the next beverage.
Please note:

• Various alarm messages could be displayed while using the appliance (Fill tank, Empty grounds container, etc.). Their meaning is explained in section “17. Troubleshooting”.
• For hotter coffee, see section “7.5 Tips for a hotter coffee”.
• If the coffee is delivered a drop at a time, too weak and not creamy enough or too cold, read the tips in section “17. Troubleshooting”.
• To customise the beverages according to personal taste, see section “9. Programming and selecting”.

7.3 Making coffee using pre-ground coffee
Important!

• Never add pre-ground coffee when the machine is off or it could spread through the inside of the machine and dirty it. This could damage the machine.
• Never use more than 1 level measure (C2) as it could soil the inside of the coffee machine or block the funnel (A4).
• When using pre-ground coffee, only one cup can be made at a time.

1. Press the button  (B11) repeatedly until “ ” appears on the display (D5);
2. Make sure the funnel is  not blocked, then add one level measure of preground coffee (fig. 10);
3. Place a cup under the coffee spouts (A9) (fig. 9);
4. Then select your required coffee:

Coffees selectable from (B10) and confirming  with (B4)
Ristretto| ≃ 30 ml
Espresso lungo| ≃ 120 ml

5. Preparation begins. The selected beverage appears on the display, together with a progress bar which gradually fills as preparation proceeds.

Please note:
At the end of delivery, to increase the quantity of coffee in the cup, just press “EXTRA” (B10) within 3 seconds. When the  required quantity is reached, stop with (B3).
Important! Making LONG coffee :
Halfway through preparation, the machine requests a further level measure of pre-ground coffee. Proceed, then press (B11).
Please note:

• If “Energy Saving” mode is active, you may have to wait a  few seconds before the first coffee is delivered.
• Various alarm messages could be displayed while using the appliance (Fill tank, Empty grounds container, etc.). Their meaning is explained in section “17. Troubleshooting”.
• For hotter coffee, see section “7.5 Tips for a hotter coffee”.
• If the coffee is delivered a drop at a time, too weak and not creamy enough or too cold, read the tips in section “17. Troubleshooting”.

7.4 Adjusting the coffee mill

The coffee mill is factory-set in such a way that the coffee will be delivered correctly and should not require regulating initially.
However, if after making the first few coffees you find that the coffee is either too weak and not creamy enough or delivery is too slow (a drop at a time), this can be corrected by
adjusting the grinding adjustment dial (A5) (fig. 11).
Please note:
The grinding adjustment dial must only be turned when the coffee mill is in operation during the initial phase of coffee preparation.
If the coffee is delivered too slowly or not at all, turn one click clockwise towards 7.
For fuller bodied creamier coffee, turn one click anticlockwise towards 1 (do not turn more than one click at a time otherwise the coffee could be delivered a drop at a time).
The effect of the adjustment will be noticed only after making at least a further 2 cups of coffee. If this adjustment does not produce the desired result, turn the dial another click.
7.5 Tips for a hotter coffee
For hotter coffee, proceed as follows:

• perform a rinse cycle by selecting the “Rinsing” function in the settings menu (section “6.1 Rinsing”);
• warm the cups with hot water using the hot water function (see section “10. Delivering hot water”);
• increase the coffee temperature in the “Settings” menu (see section “6.4 General”). Varying the temperature has most effect for long beverages.

MAKING CAPPUCCINOS AND MILK-BASED COFFEES

Please note:
To avoid milk with poor froth or large bubbles, always clean the milk container lid (D2) and hot water connection nozzle (A10) as described in sections “8.4 Cleaning the milk container after every use”, “11.10 Cleaning the milk container” and “11.11 Cleaning the hot water nozzle”.
8.1 Filling and attaching the milk container

1. Lift the milk container lid (D2) (fig. 12);
   

2. Fill the milk container (D5) with a sufficient quantity of milk, not exceeding the MAX level marked on the container (fig.13);

3. Make sure the milk intake tube (D4) is correctly inserted as far as it will go in the bottom of the milk container lid (fig. 14);
   

4. Place the lid back on the milk container;

5. Remove the hot water spout (C6) (fig. 15);

6. Attach the container to the connection nozzle (A10) and push as far as it will go (fig. 16). The machine emits a beep (if enabled);

7. Place a sufficiently large cup under the coffee spouts (A9) and frothed milk spout (D3);

8. Follow the instructions below for each function.

Please note:

• For a denser more even froth, you must use skimmed or partially skimmed milk at refrigerator temperature (about 5°C).
• The quality of the froth will vary depending on:
• type of milk or vegetable beverage;
• brand used;
• ingredients and nutritional value.
• If “Energy Saving” mode is enabled, you may have to wait a few seconds before the beverage is delivered.

8.2 Adjust the quantity of froth
Turn the froth adjustment dial (D1) to adjust the amount of froth on the milk delivered while making cappuccinos and milk-based coffees.

8.3 Making cappuccino and milk-based coffees automatically

1. Fill the milk container (D) and attach it as described above;
2. Select the required beverage:

Directly selected beverages:

• : Hot milk (B4)
•   : Macchiato (B5)
• : Cappuccino (B6)

Selectable by pressing (B10) and confirming  with (B11):

• Caffelatte
• Flat white
• Cappuccino Mix

3. After a few seconds, preparation begins automatically and the selected beverage appears on the display, together with a progress bar which gradually fills as preparation progresses;
4. After delivering the milk, the machine automatically makes the coffee (if required by the recipe).
Please note:

• (B2): press to interrupt preparation completely and  go back to the main screen.
• “STOP”  (B3): to interrupt milk or coffee delivery and  move on to the next delivery (if applicable) to complete the beverage.
• At the end of delivery, to increase the quantity of coffee in the cup, press the button corresponding to “EXTRA” –  (B10).
• Do not leave the milk container out of the refrigerator for long periods. The warmer the milk (5°C is ideal), the poorer the quality of froth produced.
• The beverages can be customised (see section “9. Programming and selecting”).

8.4 Cleaning the milk container after every us e
The milk frother lid must be cleaned each time you use a milk function:

1. Leave the milk container (D) in the machine (you do not need to empty it);

2. Place a cup or other recipient under the frothed milk spout;

3. Turn the froth adjustment dial (D1) to “CLEAN” (fig. 17). A progress bar appears and gradually fills as the operation proceeds together with “Cleaning underway”. Cleaning stops automatically;
   

4. Turn the dial back to one of the froth selections;

5. Remove the milk container and always clean the steam connection nozzle (A10) with a sponge (fig. 18).

Please note:

• If you want to prepare a number of cappuccinos or milkbased coffees, clean the milk container after you have prepared the last beverage only. In this case, when requested, press (B2) to go back to the main menu.
• If you do not clean the milk container, the symbol appears on the display to remind you that it needs cleaning.
• The milk container can be kept in the refrigerator.
• In some cases, to clean you must wait for the appliance to heat up.

PROGRAMMING AND SELECTING

In the ” my” menu you can customise the beverages according to your personal tastes.

1. Press (B3);

2. Press the scroll arrows (B3) or (B10)until the  required beverage is displayed;

3. Press (B11) to select the beverage;

4. • Beverages with coffee: “Program aroma” appears on the display (D5). Press the scroll arrows or until the required aroma is selected. Press to  confirm the selection. Preparation begins and “Program coffee” appears on the display together with a bar which gradually fills as delivery progresses. When the required quantity is reached in the cup, press  (STOP).
   • Cappuccino and milk-based coffees: after selecting and confirming the aroma, “Program milk” appears on the display together with a bar which gradually fills as milk delivery progresses. When the required quantity is reached, press .
   The appliance then makes the coffee. Press to interrupt delivery when the required quantity of coffee is reached.

5. Save the settings by pressing  (or press (B2)) .

6. “Parameters saved” or “Parameters not saved”. The appliance is ready for use again.

Please note:

• When the minimum quantity you can set is reached, “STOP” appears on the display.
• “STOP”: press the corresponding button to interrupt milk or coffee delivery and move on to the next delivery (if applicable) to complete the beverage.

DELIVERING HOT WATER

Important! Danger of scalding.
Never leave the machine unattended while delivering hot water.

1. Make sure the hot water spout (C6) is attached correctly to the hot water connection nozzle(A10);
2. Place a container under the water spout (as close as possible to avoid splashes) (fig. 6);
3. Press (B10) and scroll through the beverages in the  menu by pressing the scroll arrows (B3) or (B10) until “Hot water” is displayed;
4. Press (B11). A progress bar appears and gradually  fills as preparation proceeds;
5. The machine delivers hot water, then delivery stops automatically. To interrupt delivery of hot water manually, press (STOP).

Please note:

• If “Energy Saving” mode is active, you may have to wait a few seconds before the hot water is delivered.
• The quantity of water delivered can be customised (see section “9. Programming and selecting”).

CLEANING

11.1 Cleaning the machine
The following parts of the machine must be cleaned regularly:

• the appliance’s internal circuit;
• coffee grounds container (A17);
• drip tray (A19) and condensate tray (A16);
• water tank (A14);
• coffee spouts (A9);
• pre-ground coffee funnel (A4);
• infuser (A12), accessible after opening the door (A11);
• milk container (D);
• hot water/steam connection nozzle (A10);
• hot water spout (C6).

Important!

• Do not use solvents, abrasive detergents or alcohol to clean the coffee machine. With De’Longhi superautomatic coffee machines, no chemical products are required for cleaning purposes.
• None of the components of the machine can be washed in a dishwasher, except for the milk container (D).
• Do not use metal objects to remove encrustations or coffee deposits as they could scratch metal or plastic surfaces.

11.2 Cleaning the internal circuit
If the appliance is not used for more than 3/4 days, before using it again, we strongly recommend switching it on and:

• performing 2/3 rinse cycles (see section “6.1 Rinsing”);
• delivering hot water for a few seconds (section “10. Delivering hot water”).

Please note:
After cleaning, it is normal for the grounds container (A17) to contain water.
11.3 Cleaning the coffee grounds container
The display indicates when the grounds container (A17) is full. The appliance cannot be used to make coffee until you have cleaned the grounds container. Even if not full, the empty grounds container message is displayed 72 hours after the first coffee has been prepared. For the 72 hours to be calculated correctly, the machine must always be connected to the mains power supply.
To clean (with the machine on):

• Remove the drip tray (A19) (fig. 19), empty and  clean.
• Empty the grounds container and clean thoroughly to remove all residues left on the bottom. This can be done with the spatula on the brush (C5) provided.

When removing the drip tray, the grounds container must always be emptied, even if it has not filled up appreciably. If this is not done, when you make the next coffees, the grounds container may fill up more than expected and clog the machine.
11.4 Cleaning the drip tray
The drip tray (A19) is fitted with a level indicator (A20) (red) showing the amount of water it contains (fig. 20). Before the indicator protrudes from the cup tray (A18), the drip tray must be emptied and cleaned, otherwise the water may overflow the edge and damage the appliance, the surface it rests on or the surrounding area.

To remove the drip tray:

1. Remove the drip tray and coffee grounds container (A17) (fig. 19);
2. Remove the cup tray and drip tray grille, then empty the drip tray and grounds container and wash all components;
3. Check the condensate tray (A16) and empty if necessary (fig. 21).
4. Put the drip tray complete with grille and grounds container back in the appliance.

11.5 Cleaning the in side of the appliance
Danger of electric shock!
Before cleaning internal parts, the machine must be turned off (see section “5. Turning the appliance off”) and unplugged from the mains power supply. Never immerse the machine in water.

1. Check regularly (about once a month) that the inside of the appliance (accessible after removing the drip tray (A19)) is not dirty. If necessary, remove coffee deposits with the
   brush (C5) supplied and a sponge;

2. Remove all residues with a vacuum cleaner (fig. 22).

11.6 Cleaning the water tank

1. Clean the water tank (A14) regularly (about once a month) and whenever you replace the water softener filter (C4) (if provided) with a damp cloth and a little mild washing up liquid;
2. Remove the filter (C4) (if present) and rinse with running water;
3. Replace the filter (if installed), fill the tank (A14) with fresh water and replace;
4. (Models with water softener filter only) Deliver 100ml of water to reactivate the filter.

11.7 Cleaning the coffee spouts

1. Clean the coffee spouts (A9) regularly with a sponge or cloth (fig. 23);
2. Check the holes in the coffee spouts are not blocked. If necessary, remove coffee deposits with a toothpick (fig. 23).
   

11.8 Cleaning the pre-ground coffee funnel
Check regularly (about once a month) that the pre-ground coffee funnel (A4) is not blocked. If necessary, remove coffee deposits with the brush (C5) supplied.
11.9 Cleaning the infuser
The infuser (A12) must be cleaned at least once a month.
Important!
The infuser cannot be extracted when the machine is on.

1. Make sure the machine has run the shutdown procedure correctly (see “5. Turning the appliance off”);

2. Remove the water tank (fig. 2).
   

3. Open the infuser door (fig. 24) on the right side of the appliance.

4. Press the two red release buttons inwards and at the same time pull the infuser outwards (fig. 25);
   Important!
   RINSE WITH WATER ONLY
   NO DETERGENTS – NO DISH WASHER
   Do not use detergents to clean the infuser as this could cause damage.

5. Soak the infuser in water for about 5 minutes, then rinse under the tap;
   

6. Use the brush (C5) to remove any coffee residues left in the infuser housing, visible through the infuser door.

7. After cleaning, replace the infuser by sliding it onto the internal support (fig. 26), then push the PUSH symbol fullyin until it clicks into place
   Please note:![De Longhi ECAM46.86X Bean to Cup Espresso and Cappuccino Machine

• fig 19](https://manuals.plus/wp-content/uploads/2023/05/De-Longhi-ECAM46 .86X-Bean-to-Cup-Espresso-and-Cappuccino-Machine-fig-19.png)If the infuser is difficult to insert, before insertion, adapt it to the right size by pressing the two levers shown in fig. 27.

  8. Once inserted, make sure  the two red buttons have  snapped out (fig. 28).
  9. Close the infuser door.
  10. Put the water tank back.

11.10 Cleaning the milk container
To keep the frother efficient, clean the milk container as described below, every two days:

1. Remove the lid (D2).

2. Remove the milk spout (D3) and intake tube (D4) (fig. 29).

3. Turn the froth adjustment dial (D1) anticlockwise to the “INSERT” position (fig. 29) and pull off upwards.
   

4. All components and the container are dishwasher safe, placing them in the top basket. If you do not have a dishwasher, wash by hand as described in the note at the end of the  section. groove hollow Make sure there are no milk residues on the hollow and groove under the dial (fig. 30). If necessary, scrape the groove with a toothpick.

5. Rinse inside the froth adjustment dial seat with running water (fig. 31).

6. Check that the intake tube and spout are not clogged with milk residues.

7. Replace the dial (in correspondence to the word “INSERT”), spout and milk intake tube.

8. Place the lid back on the milk container.

Please note: washing by hand
Washing in a dishwasher guarantees the perfect hygiene of all the milk container components. When washing by hand, wash all components of the milk container thoroughly withhot water and immerse them in a basin of hot water for 30 minutes before proceeding as described in point 5.
11.11 Cleaning the hot water nozzle
Every now and then, clean the connection nozzle (A10) with a sponge to remove milk residues from the gaskets (fig. 18).

DESCALE

Important!

• Before use, read the instructions and the labelling on the descaler pack.
• It is important to use De’Longhi descaler only. Using unsuitable descaler and/or performing descaling incorrectly may result in faults not covered by the manufacturer’s guarantee.
• Descaler could damage delicate surfaces. If the product is accidentally spilt, dry immediately.

To descale

Descale the machine when the corresponding message appears on the display (D5). To descale immediately, press  (B11)  and follow the instructions from point 6. To descale later, press . (B2): on the display the symbol reminds you the appliance needs descaling.
To access the descaling menu:

1. Turn the appliance on and wait until it is ready for use;

2. Press to enter the “Settings” menu;

3. Press the scroll arrows (B3) or  (B10) until  “Maintenance” is displayed, then press ;

4. Press the scroll arrows or until “Descaling” is  displayed, then press ;

5. Confirm by pressing ;

6. (If the filter is installed): extract the water tank (A14), remove the water softener filter (C4) and empty the water tank. Press ;

7. Pour the descaler into the tank up to level A (corresponding to a 100ml pack) marked on the inner surface of the tank, then add water (one litre) up to level B (fig. 32) and put the water tank back. Press ;

8. Remove, empty and replace the drip tray (A19) and grounds container (A17). Press ;

9. Place an empty container with a recommended capacity of 2 litres under the hot water spout (C6) and coffee spouts (A9) (fig. 33). Press ;
   Important! Danger of scalding
   Hot water containing acid flows out of the coffee spouts and  hot water spout. Take care to avoid contact with splashes of this  solution.

10. The descale programme starts and the descaler liquid comes out of the hot water and coffee spouts. A series of rinses and pauses is performed automatically to remove all the scale residues inside the coffee machine; After about 25 minutes, descaling stops;

11. The appliance is now ready for rinsing through with clean water. Empty the container used to collect the descaler solution. Extract the water tank, empty, rinse under running
    water, fill with fresh water up to the MAX level and put back in the appliance. Press ;

12. Place the container used to collect the descaler solution empty under the coffee spouts and hot water spout (fig. 33) and press ;

13. Confirm by pressing ;

14. Hot water is delivered first from the coffee spouts, then from the hot water spout;

15. When the water in the tank has run out, empty the container used to collect the rinsing water;

16. Extract the water tank and fill with fresh water up to the MAX level. Press ;

17. (If the filter was installed) Put the water softener filter (if previously removed) back in its housing in the water tank (A15), and replace the tank in the appliance, then press ;

18. Place the container used to collect the descaler solution empty under the hot water spout. Press ;

19. “Rinsing Confirm?”: press ;

20. “Rinsing underway”. Hot water comes out of the hot water spout;

21. When descaling is complete, press ;

22. “Empty drip tray”: At the end of the second rinse, remove, empty and replace the drip tray (A19) and grounds container (A17). Press ;

23. Empty the container used to collect the rinse water, remove the water tank and fill with fresh water up to the MAX level, then put back in the appliance.

The descaling cycle is now complete.
Please note:

• If the descaling cycle is not completed correctly (e.g. no electricity) we recommend repeating the cycle;
• After descaling, it is normal for the grounds container (A17) to contain water;
• If the water tank has not been filled to the MAX level, at the end of descaling, the appliance requests a third rinse to guarantee that the descaler solution has been completely
  eliminated from the machine’s internal circuits. Before starting rinsing, remember to empty the drip tray.

SETTING WATER HARDNESS

The descaling request is displayed after a period of time established according to water hardness.
The machine is set by default for a hardness level of 4. The machine can also be programmed according to the hardness of the mains water in the various regions so that the  machine needs to be descaled less often.
13.1 Measuring water hardness

1. Remove the “TOTAL HARDNESS TEST” indicator paper (C1) from its pack (attached to the English instructions);
2. Immerse the paper completely in a glass of water for one second;
3. Remove the paper from the water and shake lightly. After about a minute, 1, 2, 3, or 4 red squares form, depending on the hardness of the water. Each square corresponds to 1 level;

13.2 Setting water hardness

1. Press (B2) to enter the menu;
2. Press the scroll arrows  (B3) or  (B10) until  “General” is displayed;
3. Press   (B11) to confirm;
4. Press the scroll arrows  or until “Water hardness” is displayed:
5. Press . The current value appears on the display (D5)  and the “New” value flashes;
6. Select the new value you want to set using the scroll arrows or ;
7. After selecting the quantity, press .

The display goes back to the previous screen. Press twice to go back to the main screen.

WATER SOFTENER FILTER

Certain models are fitted with a water softener filter (C4). If this is not the case with your model, you are recommended to purchase one from De’Longhi customer services. To use the filter correctly, follow the instructions below.

14.1 Installing the filter

1. Remove the filter (C4) from the packaging. The date indicator disk varies according to the filter provided.

2. Turn the date indicator disk (fig. 34) until the next 2 months of use are displayed. Please note
   The filter lasts about two months if the appliance is used normally. If the coffee maker is left unused with the filter installed, it will last a maximum of three weeks.

3. To activate the filter, run tap water through the hole in the filter as shown in fig. 35 until water comes out of the openings at the side for more than a minute;

4. Extract the tank (A14) from the appliance and  fill with water;

5. Insert the filter in the water tank and immerse it completely for about ten seconds, sloping it and pressing it lightly to enable the air bubbles to escape (fig.36);

6. Insert the filter in the filter housing (A15) and press fully home (fig. 37);

7. Close the tank with the lid (A13) (fig. 38), then replace the tank in the machine;

8. When you install the filter you must notify the appliance of its presence.

9. Press (B2) to enter the “Settings” menu;

10. Press the scroll arrows (B3) or (B10)until  “Maintenance” is displayed, then press  (B11);

11. Press the scroll arrows until “Install filter” is displayed, then press ;

12. Press to confirm;

13. Place an empty container with a minimum capacity of 500 ml under the hot water spout (C6), then press to  start delivery;

14. The appliance starts delivering water;

15. After the flow of hot water stops, the appliance automatically reverts to ready for use again.

The filter is now active and you can use the coffee machine.

14.2 Replacingthe filter
Replace the filter (C4) when requested by the appliance. To replace immediately, press (B11) and follow the instruc- tions from point 8. To replace the filter later, press (B2).
The symbol appears on the display to remind you that the filter needs replacing.
To replace, proceed as follows:

1. Extract the tank (A14) and exhausted filter;
2. Take the new filter out of its packet and proceed as illustrated in points 2, 3, 4, 5, 6 and 7 in the previous section;
3.  Press to enter the “Settings” menu;
4.  Press the scroll arrows  (B3) or (B10) until  “Maintenance” is displayed, then press ;
5. Press the selection arrows until “Replace filter” is displayed, then press ;
6. Press to confirm;
7. Place an empty container with a minimum capacity of 500 ml under the hot water spout (C6), then press  (fig. 8) to start delivery;
8. After the flow of hot water stops, the appliance automatically reverts to ready for use again.

Please note:
After two months (see date indicator) or when the appliance has not been used for 3 weeks, you should replace the filter even if the message has not yet been displayed.
14.3 Removing the filter
If you want to use the appliance without the filter (C4), you must remove it and notify the appliance of its removal. Proceed as follows:

1. Extract the tank (A14) and exhausted filter;
2. Press (B2) to enter the “Settings” menu;
3. Press the scroll arrows  (B3) or (B10)until  “Maintenance” is displayed, then press  (B11);
4.  Press the scroll arrows   or  until “Remove filter” is displayed, then press ;
5. Press  to confirm removal. The appliance goes back  to the previous screen;
6. Then press  twice to exit the menu.

Please note:
After two months (see date indicator) or when the appliance has not been used for 3 weeks, you should replace the filter even if the message has not yet been displayed.

TECHNICAL DATA

De’Longhi reserves the right to modify the technical specification and styling of its products at any moment, without compromising their functionality and quality.

15.1 Tips for Energy Saving

• To reduce energy consumption, after delivering one or more beverages, remove the container (D) or accessories.
• Set auto-off to 15 minutes (see section “6.4 General”);
• Enable Energy Saving (see paragraph “6.4 General”);
• When requested by the machine, perform the descaling cycle (see section “12. Descale”).

DISPLAYED MESSAGES

and/or insert it correctly, pushing it as far as it will go until it clicks into place (fig. 4).
Insert tank| The tank (A14) is not correctly in place.| Insert the tank correctly and press as far as it will go (fig. 4).
Empty grounds container| The grounds container (A17) is full.| Empty the grounds container and drip tray (A19), clean and replace. Important: when removing the drip tray, the grounds container MUST be emptied, even if it contains few grounds. If this is not done, when you make the next coffees, the grounds container may fill up more than expected and clog the machine.
Insert grounds container| After cleaning, the grounds container (A17) has not been replaced.| Remove the drip tray (A19) and insert the grounds container.
Add pre-ground coffee ESC to cancel| The pre-ground coffee function has been se- lected without placing any pre-ground coffee in the funnel (A4).| Place pre-ground coffee in the funnel or deselect the pre-ground function.
Add pre-ground coffee ESC OK| A LONG coffee with pre-ground coffee has been requested| Put one level measure of pre-ground coffee into the pre-ground coffee funnel (A4) and press (811) to continue and complete preparation.
Fill beans container ESC to cancel| The coffee beans have run out.| Fill the beans container (A4) (fig. 8).
The pre-ground coffee funnel (A4) is dogged.| Empty the funnel with the help of the brush (C5) as described in section “11.8 Cleaning the pre-ground coffee funnel’:
Ground too fine Adjust mill
ESC to cancel| The grinding is too fine and the coffee is deliv- ered too slowly or not at all.| Repeat coffee delivery and turn the grinding adjustment dial (A5) (fig. 11) one dick clockwise towards “7” while the coffee mill is in operation. If after making at least 2 coffees delivery is still too slow, repeat the correction procedure, tuming the grinding adjustment dial another dick (see section “7.4 Adjusting the coffee mill”). If the problem persists, make sure the water tank (A14) is fully inserted.
If the water softener filter ((4) is present, an air bubble may have been released inside the circuit, obstructing delivery.| Insert the hot water spout (() in the appliance and deliver a little water until the flow be-comes regular.
less coffee ESC to cancel| Too much coffee has been used.| Select a lighter taste by pressing (B11) or reduce the quantity of pre-ground coffee.
Insert water spout| The hot water spout (C6) is not inserted or is inserted incorrectly.| Fully insert the hot water spout (fig. 5).
Insert milk container| The milk container (D) is not inserted correctly.| Insert the milk container (fig. 16) as far as it will go.
Insert infuser assembly| The infuser has not been replaced after
deaning.| Insert the infuser as described in section “11.9 Cleaning the infuser.
Water circuit empty Fill water circuit
Hot water Confirm?| The water circuit is empty.| Press (B11) and deliver water from the spout (C6). If the problem persists, make sure the water tank (A14) is fully inserted.
Press OK to (LEAN| The milk container (D) has been inserted with the froth adjustment dial (D1) in the “CLEAN” position.| To proceed with the CLEAN function press (B11) or turn the froth adjustment dial to another position.
Set dial to (LEAN ESC to cancel| Milk has been delivered recently and the tubes inside the milk container (D) must be cleaned.| Turn the froth adjustment dial (D1) to CLEAN (fig. 20).
Turn froth adjustment dial| The milk container (D) has been inserted with the froth adjustment dial (D1) in the “CLEAN” position.| Turn the froth adjustment dial to one of the milk froth positions.
Descale ES( to cancel OK to descale (-45 minutes)| The machine must be desca led.| The descaling procedure described in section “12. Descale” needs to be performed.
Replace filter ESC to cancel OK to replace| The water softener filter “C4. Filtro addolcitore (se previsto)” is exhausted.| Replace the filter or remove it as described in section “14. Water softener filter”.
General alarm| The inside of the appliance is very dirty.| Clean the inside of the appliance thoroughly, as described in section “11. Cleaning”. If the message is still displayed after cleaning, contact a customer service centre.
| The tubes inside the milk container (D) must be cleaned.| Turn the froth adjustment dial (D1) to CLEAN (fig. 17).
| The water softener filter (C4) is exhausted and must be replaced or removed.| Replace the filter or remove it as described in section “14. Water softener filter”.
| The machine must be descaled.| The descaling procedure described in section “12. Descale” needs to be performed.
The appliance may request descaling cycles at very short intervals. This is normal and due to the appliance’s advanced control system.
**ECO**| Energy saving is enabled.| To disable energy saving, proceed as described in section “6.4 General” – “Energy saving:”

TROUBLESHOOTING

Below is a list of some of the possible malfunctions.
If the problem cannot be resolved as described, contact customer services.

them with hot water (Please note: you can use the hot water function).
The internal circuits of the appliance have cooled down because 2/3 minutes have elapsed since the last coffee was made.| Before making coffee, heat the infuser by performing a rinse cycle (see section “6.1 Rinsing”).
A low coffee temperature is set.| Set a higher coffee temperature in the menu (see section “6.4 General””Set temperature:”)
The coffee is weak or not creamy enough.| The coffee is ground too coarsely.| Turn the grinding adjustment dial (A5) one click anticlockwise towards “1” while the coffee mill is in operation (fig. 11). Continue one click at a time until coffee delivery is satisfactory. The effect is only visible after delivering 2 coffees (see section “7.4 Adjusting the coffee mill”).
The coffee is unsuitable.| Use coffee for espresso machines.
The coffee is delivered too
slowly or a drop at a time.| The coffee is ground too finely.| Turn the grinding adjustment dial (A5) one dick clockwise towards “7” while the coffee mill is in operation (fig. 11). Continue one did at a time until coffee delivery is satisfactory. The effect is only visible after delivering 2 coffees (see section ‘7.4 Adjusting the coffee mill”).
The LONG coffee is too creamy| The coffee is ground too finely.| Turn the grinding adjustment dial “AS. Grinding adjustment dial” one click dockwise towards ‘7″ while the coffee mill is in operation (fig. 11). Continue one dick at a time until coffee delivery is satisfactory. The effect is visible only after 2 coffees have been made.
The appliance will not make coffee| The appliance has detected impurities in its internal circuits. “Please wait” is displayed.| Wait for the appliance to be ready again and reselect the required beverage. Contact customer services if the problem persists.
Coffee does not come out of one or both of the spouts.| The coffee spouts (A9) are blocked.| (lean the spouts with a toothpick (fig. 23).
The appliance does not come on| It is not plugged into the mains socket.| Plug into the mains socket (fig. 1).
The infuser cannot be removed| The appliance has not been turned off correctly| Turn the appliance off by pressing the button (A7) (fig. 9) (see section “5. Turning the appliance off”).
At the end of descaling, the appliance requests a third rinse| During the two rinse cycles, the water tank (A14) has not been filled to the MAX level.| Follow the instructions displayed by the appliance, but first empty the drip tray (A19) to avoid the water overflowing.
Milk does not flow from the milk spout (D3)| The milk container lid (01) is dirty| Clean the milk container lid as described in sec-tion “11.10 Cleaning the milk container”.
Make sure the milk intake tube (D4) is correctly inserted in the bottom of the milk container lid (fig. 14)| Insert the milk intake tube as far as it will go
The milk contains large bubbles and squirts out of the milk spout (D3) or there is little froth| The milk is not cold enough or is not semi- skimmed or skimmed| Use skimmed or semi-skimmed milk at refrigerator temperature (about 5°C). If the result is
not as you wished, try changing brand of milk.
The froth adjustment dial (D1) is incorrectly adjusted.| Adjust following the instructions in section “8.2 Adjust the quantity of froth”.
The milk container lid (D1), froth adjustment dial (D1), or milk intake tube (D4) are dirty| (lean the milk container lid, dial and milk intake tube as described in section . “11.10 (leaning the milk container”.
The hot water connection nozzle (A10) is dirty| Clean the connection nozzle as described in section “11.11 Cleaning the hot water nozzle”.
The machine emits noises or small puffs of steam while not in use| The machine is ready for use, or has recently been turned off, and condensate is dripping into the hot vaporiser| This is part of normal operation. To limit the phenomenon, empty the drip tray.

www.delonghi.com/register

5713246821_02_1020
De’Longhi Appliances via Seitz, 47 31100 Treviso, Italy www.delonghi.com

References

• YouTube
• De'Longhi | Espresso Machines, Kitchen & Home Appliances

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>