SONOFF L3-5M Smart LED Strip Lights User Manual

SONOFF L3-5M Smart LED Strip Lights

Product Information

The L3 & L3 Pro smart LED strip lights, manufactured by Shenzhen SonoffTechnologies Co., Ltd., are a set of Wi-Fi and Bluetooth-enabled LED strips that can be controlled through the eWeLink App on your mobile phone. The L3 model comes with a 5-meter long strip and 90 LED bulbs, while the L3 Pro model comes with a 5-meter long strip and 150 LED bulbs. The LED strips have an IP20 and IP54 rating respectively, making them suitable for indoor and outdoor use. The LED strips have a life expectancy of approximately 30,000 hours and work on an input voltage of SVDC.

Controller introduction

Button features

• Short press: Turn on/off the strip light
• Long press for Ss: Make strip light enter in the pairing mode (LED indicator flashes)

Short press the button to exit the pairing mode while it is in the pairing mode.

Features
L3&L3 Pro both are smart strip lights, which have 16 million colors and support switching various scene modes through your smartphone or voice control. Also, you can select different modes based on the music styles to sync the music with gorgeous lighting.

Operation instruction

1. Clean the surface

2. Peel off the protective film

3. Stick it on

4. Download the eWeLinkApp

5. Power on
   Power on the LED strip light with a Type-C USB cable, after powering on, it will enter the Bluetooth pairing mode by default and flash.
   The strip lights will I exit the Bluetooth pairing mode if it not be paired within 3 mins. If you want to enter this mode again, please long press the controller for Ss until the strip lights “flashes” and then release.

6. Add light strip
   Tap “+” and select “Bluetooth Pairing”, then operate following the prompt on the App.

Wi-Fi Settings

Select the “Wi-Fi Settings” on the “Device Settings” interface in the eWeLink App to add or change the network.
When Wi-Fi is disconnected, the device will automatically switch to Bluetooth control (Ensure Bluetooth is enabled on your mobile phone).

Specifications

Light Strips

Controller

Cuttable

• L3: Cutable every 55.55mm
• L3 Pro: Cutable every 33.33mm

Please note that the light strips cannot be restored if you cut it.

Product Usage Instructions

To use the L3 & L3 Pro smart LED strip lights, follow these steps:

1. Download and install the eWeLink App on your mobile phone.
2. Connect the LED strip to a power source using the provided SVDC input.
3. In the eWeLink App, select “Wi-Fi Settings” on the “Device Settings” interface to add or change the network. Make sure your Wi-Fi is enabled and connected to a network.
4. You can now control the LED strip lights through the eWeLink App on your mobile phone. You can turn them on/off, change the  color temperature, and adjust the brightness
5. If your Wi-Fi connection is lost, the device will automatically switch to Bluetooth control. Make sure your Bluetooth is enabled on your mobile phone to continue controlling the LED strips.

Factory Reset

Deleting the device on the eWelinkApp indicates you restore it to factory setting.

Safety Warning

1. Before use, please confirm that the voltage is appropriate for this product’s working voltage. Using inappropriate voltage may damage the product and bring safety hazards.
2. LED Light Sources are unchangeable, please don’t dismantle them.
3. The Strip Lights will generate heat during working, please keep air circulation for heat dissipation.

FCC Warning

Changes or modifications not expressly approved by the party responsible for compliance could avoid the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Hereby, Shenzhen Son off Technologies Co., Ltd. declares that the radio equipment type L3-5M/L3-5M-P are in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://sonoff.tech/usermanuaIs.

Shenzhen SonoffTechnologies Co., Ltd.
3F & 6F, Bldg A, No. 663, Bu long Rd, Shenzhen, Guangdong,
China ZIP code: 518000
Website: sonoff.tech

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>