xiwxi BH-T10 Hybrid Active Noise Cancellation Earbuds User Manual
- June 11, 2024
- XiWXi
Table of Contents
xiwxi BH-T10 Hybrid Active Noise Cancellation Earbuds
User Manual
Thanks for using our wireless electronic products. For a good user experience,
please read the manual carefully before using the products. Notice: To avoid
unnecessary troubles, please do not disassemble these products by yourself,
and please use the standard charger to charge.
Product Overview
- Choose the ear cap that suits you.
- Make sure that the ear caps face down and put the earbuds into the ear in the angle shown as the picture on the right
- After putting on the earbuds, gently rotating the earbuds to a comfortable and secure position shown as picture 3 on the right. Now the earbuds are put on correctly
- Do not wear the earbuds like the way shown as the picture on the right
First time using
-
Tear off the insulating film
-
Put the earbuds into the charging case and close the lid to charge(the earbuds are in charging state).
-
Open the lid of the case, and they will automatically turn on and pair with each other, then ready for pairing to the phone (both turn red and blue alternately) .
When there is no sound or the earbuds do not turn on, please put them back into the case and close it. Please make sure that they are charging with light on before opening the case again. Then take them out to use ( both flash red and blue alternately) .
-
Turn on the Bluetooth function on your phone and search for【BH-T10】and connect it.
Warm notice：
When there is no sound or the earbuds do not pair to the phone, please press
both earbuds’ power switch three times to start TWS pairing, both flash blue
quickly and turn to red and blue alternately when connected.
PS : Not applicable when connected.
If you want to switch the Bluetooth connection to another device, please disable the Bluetooth function in the previously connected device OR delete the pairing name of “BH-T10” from the original device. Then the pairing name of “BH-T10” can be searched in new device and connected successfully.
Button control
Active Noise Cancellation
TWS State
When not on the phone, tap the MFB on the left earbud to switch among the following modes : when the earbuds turn on, they are defaulted to be ANC Off
Restore factory setting
- When pairing to the phone, please tap both earbuds five times to reset them. They will disconnect and turn off, then power on again.
- Please delete all paired records on the phone and search again for “BH-T10″on the bluetooth of mobile phone and reconnect.
Earbuds indicator
- State Indicator
- Turn on Flashes blue for 1s
- Turn off Flashes red for 1s
- Pairing Both flash blue quickly
- Connected No light
- Music play No light
- Low battery Flashes red every 4s
- Charging Red light on
- Full battery Red light off
Charging case indicator
- Status Indicator
- Charging for case White light flashes
- Full Battery Four lights on the charging case keep white
- Open/Close White on for a few seconds
- Charging for earbuds White light on
- Low Battery First light on the left flashes white
Specifications
- Version V5.0
- Support HFP,HSP,A2DP,AVRCP
- Transmission distance 10m
- Frequency range 2.402GHz~2.480GHz
- Speaker Φ 10mm*2
- Impedance 32 Ω
- Standby time (no music, ANC off) About 72 hours
- ANC (ON)/ Transparency (ON) : About 7 hours Music Playing Time
- ANC (OFF)/ Transparency (OFF) : About 10 hours Music Playing Time
- Talk time About 5 hours
- Earbud battery capacity 40mAh Fully charged time About 1.2 hour
- Charging case battery capacity 400mAh
- Charging time of charging case About 1.5 hour
- Weight (single earbud) 4.8 g
Note : Please put both earbuds in the charging case to fully charge them on first use
Charging The Case
Please use a charger with an output voltage of DC5V/1A to charge the charging
case. You can also use a computer USB or other USB interface charger to charge
( please DO remember to choose the charger authorized by formal manufacturer
).
Signal transmission distance shown as below:
Notice:
- When the charging case is out of power, it may cause the earbuds fail to shut down and remain connected to the phone even when they are placed in the charging case. So please remember to charge the charging case in time
- If moisture remains in the audio output hole, the sound may become fuzzy or completely inaudible. This is quite a normal case. In this case, please remove the earbuds and shake the audio output hole down several times to allow water to flow out or let it air dry for 1-2 hours, then the sound quality will become normal.
- If there is noise, broken sound, or low sound, please take off the silicone ear cap and wipe it with a cotton swab.
- If the earbud is not charging properly, please wipe the charging column with a cotton swab, and then charge it again.
Attentions
If there is water droplet on the surface, please wipe it with a dry cloth before putting them back into the charging case to avoid damaging the device.
Tip:
- If the product is dirty, please do not rinse it directly with water or use boiling water to soak and disinfect it. It is recommended to wipe the earbuds with an alcohol cloth or a wet tissue.
- If the product falls into the water accidentally, please pick it up in time and let it dry by the natural wind under the sunshine for two hours before using it (otherwise it will affect the sound quality, thus fails to give you a better experience)
- Do not use corrosive liquid to clean this product.
- When it is stained with any chemicals, please rub it with a damp cloth wet with clean water.
- Do not use this product under extreme circumstances for temperatures below -10 degree Celsius or above 60 degrees Celsius.
- To avoid an explosion, please do not throw this product into fire.
- To avoid scratches, please do not touch the earbuds with sharp objects.
- Do not insert objects into the earbuds, otherwise, it would cause damage to the internal components.
- Do not disassemble the earbud.
- Please keep regular charge to earbuds, don’t leave them to become empty battery status to keep their lifetime.
- Please do not charge this product with a power adapter over 2A current. Excessive current may cause damage to the battery.
Battery Warning！
There is a built-in lithium battery in this product. To avoid explosion, do
NOT expose the product to intense sunlight, fire or throw it into fire.
FCC
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note : This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet the general RF exposure requirements. The device can be used in portable exposure conditions without restriction.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>