WYZE Cam V3 Pro 2K Smart Camera User Guide
- June 11, 2024
- Wyze
Table of Contents
WYZE Cam V3 Pro 2K Smart Camera User Guide
GET BETTER SECURITY WITH
Record Full-Length Videos
Get unlimited full-length video recordings.
Smart AI Detection
Detect people, packages, vehicles, and more.
Back-to-Back Event Recording
Capture everything without 5-minute gaps.
Exclusive Discounts
Get exclusive discounts on Wyze products.
Subscribe or learn more at services.wyze.com.
IN THE BOX
- Wyze Cam v3 Pro: × 1
- USB Cable: × 1
- Wall Plate: × 1
- Power Adapter: × 1
- Mounting Tape: × 1
- Mounting Screw: × 1
- Quick Start Guide: × 1
**FRONT
BACK
BOTTOM
**
- Spotlight
- Microphone
- Status Light
- Lens
- Speaker
- Micro USB Port
- MicroSD Slot (Card not included)
- SETUP Button
- 1/4” Mount (Unscrew to access)
- Mounting Hole
SETUP
-
Connect the camera to a power outlet and wait for 20 seconds or until the status light flashes red.
-
Press the SETUP button for 3 seconds or until there is a voice prompt.
-
Follow the instructions in the Wyse app to finish setup.
SPOTLIGHT
- Turn the spotlight on and off manually from the live stream. Go to Camera Settings > Spotlight Settings to adjust the brightness, set schedules, and more.
Tip: The spotlight has two brightness levels.
STATUS LIGHT GUIDE DURING INSTALLATION
Solid red light
The device is powered on and initializing
Flashing red light
The device is ready to connect
Flashing red & blue lights
Connection is in progress
Flashing blue light
The device is connected and finishing setup
Solid blue light
The device is working properly
STATUS LIGHT GUIDE AFTER SETUP
Solid red light
Live stream is being viewed or a recording is in progress
Quickly flashing red light
Siren is in use
Soild blue light
The device is working properly and no operations are running
WALL MOUNT
Install the expansion tube and screws first, and then hang wyze cam v3 pro on the screws.
Note: Use one screw, size M3x24 (Length 0.94″, Diameter 0.2″).
FCC WARNING
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC RADIATION EXPOSURE STATEMENT
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.
ISED RSS WARNING
This device complies with ISED licence-exempt RSS standard(s). Operation is subject to the following two conditions:
- this device may not cause interference, and
- this device must accept any interference, including interference that may cause undesired operation of the device.
ISED RADIATION EXPOSURE STATEMENT
This equipment complies with ISED RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body. Only use the power supply provided. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NEED HELP?
BESOIN D’AIDE? NECESITA AYUDA?
Contact our Support Team:
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>