Electrolux ELTG7300AW 4.4 Cu. Ft. Washer and 8 Cu. Ft. Gas Dryer Instructions

*Installation for Electrolux Laundry Center*
Please refer to the Use & Care manual provided with this appliance for further details.

WARNING – RISK OF FIRE

Read all the following instructions before installing and using this appliance.

• The installation and service of this Laundry Center must be performed by a qualified installer, service agency or the gas supplier.
• THIS EQUIPMENT HAS TWO CONNECTIONS TO THE POWER SUPPLY. DISCONNECT BOTH POWER SUPPLY CONNECTIONS BEFORE SERVICING. Each appliance shall be connected to an individual branch circuit only. The washer and dryer must be on separate circuits.
• DO NOT install a clothes dryer with flexible plastic or flexible foil venting material. Flexible venting materials are known to collapse, be easily crushed and trap lint. These conditions will obstruct clothes dryer airflow and increase the risk of fire.
• Ensure the entire dryer exhaust system is clean and free of lint and debris prior to the installation of your new Laundry Center. The entire exhaust system should be inspected and cleaned a minimum of every 18 months with normal usage. Failure to comply with cleaning your exhaust system will increase the RISK of FIRE.
• For your safety the information in this manual must be followed to minimize the risk of fire or explosion or to prevent property damage, personal injury or loss of life. Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
•  Install the appliance according to the manufacturer’s instructions and local codes.
• The electrical service to the appliance must conform with local codes and ordinances and the latest edition of the National Electrical Code, ANSI/NFPA 70, or in Canada, the Canadian Electrical Code CSA C22.1 part 1.
• To avoid back or other injury, have more than one person move or lift the appliance.
• Do not stack this appliance on a pedestal.
• Turn off power at the circuit breaker or fuse box before installation.
  The instructions in this manual and all other literature included with this appliance are not meant to cover every possible condition and situation that may occur. Good safe practice and caution MUST be applied when installing, operating and maintaining any appliance.

Removing Foam Packaging and Shipping Hardware

Tape doors closed. Do not allow the unit to fall.

1. Carefully tilt forward.

2. Remove plug.

3.  Return unit upright.

4. Twist and slide unit to rear of pad.

5. Tilt backward and remove pad.

6. Return unit upright.

7. Remove and save the shipping bolts.

8.  Insert hole plugs (in bag).
   

Leveling the Laundry Center

1. Place a level on top of the laundry center with the unit within 3 ft (1m) of the final location.
2. Use an adjustable wrench to adjust the leveling legs so the unit is level front-to-rear and side-to-side, and stable corner-to-corner.
3.  Press down on alternate corners and sides and feel for the slightest movement. Adjust the appropriate leg(s) so the unit sits solidly on the floor on ALL four legs. Keep the leveling leg extension at a minimum for best performance of the laundry center.

Connecting Water Line (steam dryer models only)

If this is not a steam model, skip to section 4

1.  Inspect all hoses for rubber washers prior to use.
2. Run water from cold outlet to clear contaminants.
3. Connect the dryer Assembly Hose Kit hose extensions from the cold supply to the “Y” connector, then from the “Y” connector to the water inlet on the dryer.
4. Attach the washer cold water supply line to the “Y” connector.
5. Tighten all connections by hand, then tighten additional 2/3 turn with pliers.
6. Turn on water and check for leaks.

Assembly Hose Kit P/N 5304495002 is not included with purchase of steam model and MUST be purchased separately.
For detailed information, refer to “Connecting the Water (Steam Models Only)” in the Installation sections of the Use & Care manual provided with this laundry center.

Connecting the Water line (washer)

• Skip steps 1 and 2 below if this model has a steam dryer.
• Inlet hoses are not included and MUST be purchased separately.

1. Run some water from the hot and cold faucets to flush the water lines and remove particles that might clog the water valve screens and to determine which faucet is hot and which is cold supply.

2. Check to ensure that the inlet hoses have the rubber washer firmly in place.

3. Connect the HOT hose to the RED connection on the washer and the COLD hose to the BLUE connection on the washer. Tighten by hand until snug. Then tighten each supply connection another 2/3 turn with pliers. Do not cross thread or over-tighten these connections.

4.  Connect the HOT inlet hose to the HOT water supply and the COLD inlet hose to the COLD water supply, or to the “Y” connector (section 3) if this is a steam model.

5.  Tighten by hand until snug. Then tighten each supply connection another 2/3 turn with pliers.
   Do not bend, kink or pinch water inlet hoses.

6. Turn on the water and check for leaks.

For detailed information, refer to “Connecting the Water” in the Installation sections of the Use & Care manual provided with this laundry center.

Connecting the Drain (Washer)

1. Verify the anti-siphon disc is in place.

2.  Form a “U” shape on the end of the drain hose with the hose pointed toward the drain.
   Place the formed end in a laundry tub or a standpipe and secure the drain hose with the cable tie (provided in the enclosure package) to the standpipe, inlet hose, laundry tub, etc. so the hose does not pull out from the force of the water.

3. Run the washer through a complete cycle, checking for water leaks and proper operation.

NOTE
The standpipe inside diameter must be 1-1/4” (3.2 cm) minimum. There must be an air gap around the drain hose in the standpipe. A snug hose fit can cause a siphoning action.
For detailed information, refer to “Connecting the Drain” in the Installation sections of the Use & Care manual provided with this laundry center.

TO INSTALLER: Leave these instructions with the customer.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

Electrical Requirements

Electric Dryer

1. CIRCUIT – Individual 30A branch circuit fused with 30A time delay fuses or circuit breakers.
2. POWER SUPPLY – 3-wire or 4-wire, 240V, single phase, 60Hz, AC. The power cord is NOT supplied with unit.
3. OUTLET RECEPTACLE – NEMA 10-30R or NEMA 14-30R receptacle to be located so the power supply cord is accessible when the dryer is in the installed position.

Gas Dryer and Washer

1.  CIRCUIT – Individual, properly polarized and grounded 15A branch circuit fused with 15A time delay fuse or circuit breaker.
2.  POWER SUPPLY – 2 wire, with ground, 120V single phase, 60Hz, AC.
3. OUTLET RECEPTACLE – Properly grounded 3-prong receptacle to be located so the power supply cord is accessible when the washer is in an installed position.

Connecting or Constructing Vent Exhaust (Dryer)

Exhaust system must be vented outside with approved vent hood. No screen or grate of any mesh size is allowed to cover the exhaust opening.

• Use only 4 inch rigid or semi-rigid metal ducting.
• Clean lint from duct system.
• Use only metal foil tape to connect ducts (no screws).
• Use 4″ (10.2 cm) clamp to connect dryer & exhaust system.
•  Use 90° quick-turn elbow to vent left or right from dryer. Never exceed more than 4 – 90˚ elbows in the exhaust duct system.
  See Clearance Requirements in the Pre-Installation sections of the Use & Care manual provided with this laundry center.

 MAX Number of 90°
turns| MAXIMUM LENGTH*
of 4″ (10.2 cm) Rigid Metal Duct
---|---
VENT HOOD TYPE
(Preferred)|
| | |
0| 125 ft. (38 m)| 110 ft. (33.5 m)
1| 115 ft. (35 m)| 100 ft. (30.5 m)
2| 105 ft. (32 m)| 90 ft. (27.5 m)
3| 95 ft. (29 m)| 80 ft. (24.5 m)
4| 85 ft. (26 m)| 70 ft. (21.5 m)

Connecting to Gas or Electric (Dryer)

Gas Dryer

1. Apply approved thread sealant.
2. Wrench-tighten gas line.
3. Open gas valve and check for leaks with soapy water.

DANGER
If using LP (Liquid Propane) STOP and install the LP kit before operating your gas dryer.
Electric Dryer

For detailed information, refer to the Installation sections of the Use & Care manual provided with this laundry center.

Completing the Installation

1. Plug both power cords into grounded outlets.

2.  Turn on the power at a circuit breaker/fuse box. Carefully slide the laundry center to its final position.
   Recheck leveling and rock corners for stability. See “2 Leveling the Laundry Center”. Remove and discard any tape on doors.

3.  Run the washer through a complete cycle, checking for water leaks and proper operation.

4.  Run the dryer for a few minutes to check for proper operation.

5.  If you have any questions during initial operation, please review the troubleshooting section in the Use & Care manual before calling for service.

For support in the U.S. call 1-877-4ELECTROLUX (1-877-435-3287) or visit www.electroluxappliances.com. For support in Canada call 1-800-265-8352 or visit www.electroluxappliances.ca.

A25903101 (2303)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>