Philips HR2382 Pasta Maker Machine User Manual

Philips HR2382 Pasta Maker Machine

Introduction

Congratulations on your purchase, and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips.com/welcome.

Product Overview

b

| Safety switch hole of the mixing chamber lid| ****

j

| Front panel knobs
c| Power cord| k| Front panel
d| Disc holder safety switch| l| Shaping disc
e| Main unit| m| Disc holder
f| Shaping disc storage| n| Disc holder safety switch lever
g| Water cup| o| Mixing paddle
h| Cleaning brush| p| Mixing chamber

Control panel overview

This appliance allows you to make the pasta you need in the way you want.

• Default pasta-making function

  • Choose a program with the Program selection button, and then press the Start/pause button.
    This applies when making pasta with the scaling function.

• Extrusion-only function

  • Press the Extrusion only button, and then the Start/pause button.
    This applies when there is leftover dough in the mixing chamber, and you want some extra extrusion.

• Skip-scaling function

  • Press and hold the Start/pause button for 5 seconds.
    This applies when the device jumps into error mode or when you need to skip the scale function and start the mixing process directly.

Available Accessories

Shaping discs

Note: The cleaning tool of the angel hair shaping disc is only supplied with the angel hair shaping disc.

Disassembling and cleaning before first use

1. Remove the mixing chamber lid.

2. Loosen the front panel control knobs.
   Note: The front panel is heavy. Take extra caution when removing it.

3. Disassemble the front panel, the shaping disc, the shaping disc holder, the mixing paddle, and the mixing chamber in order.

4. Clean all detachable parts, and wipe them dry.

Assembling

1. Push the mixing chamber into the appliance.
2. Point the mixing paddle to the hole in the main unit. Insert the mixing paddle all the way into the main unit.
3. Attach the disc holder to the appliance.
4. Put the shaping disc onto the disc holder, and make sure it is firmly fixed on the disc holder. Note: Make sure the inner cavity of the shaping disc and disc holder is properly fitted.
5. Attach the front panel to the main unit. Note:
   • Make sure the front panel is completely fastened before using the appliance.
   • The front panel is heavy. Take extra caution when assembling it.
6. Fasten the front panel control knobs. Note: If the front panel or the shaping disc is not properly assembled, a safety switch will prevent the appliance from working.
7. Close the mixing chamber lid. Note: If the mixing chamber lid is not properly installed, the safety switch will prevent the appliance from working.

Using the Pasta maker

Start preparation

1. Put the plug in the power socket. The pasta maker sounds once, and all indicators flash once. Note: Make sure that all the parts are well assembled before plugging in.
2. Press the On/off button to turn on the appliance.
3. Select the pasta type with the Program selection button.
   Program| Tip| Optional recipe
   ---|---|---
   Plain pasta/noodle| •    Pasta with flour and water only| •    Wheat noodle

•    Durum noodle

Egg or flavored pasta/noodle| •    Pasta with flour and egg liquid

•    All kinds of flavored pasta

| •    Wheat pasta

•    Durum pasta

•    Carrot pasta/noodle

•    Tomato pasta/noodle

•    Soba

•    Beet pasta/noodle

Note: For more recipes, refer to the recipe book.

4. Remove the mixing chamber lid. (Fig. 3)

5. Wait until 0:00 displays on the screen.

6. Pour the flour into the chamber. Note

   • The appliance automatically weighs and displays the amount of flour. The weight measurement will blink until you are in the right range.
   • Do not put less than 200g or more than 600g of flour in the chamber.
   • Some recipes (for example cookies, and gluten-free pasta) require you to skip the weighing part. In this case, press the Start/pause button for 5 seconds, and the appliance will start mixing and extruding directly.

7. Close the chamber lid. (Fig. 14)
   Note

   • If you press a button without closing the lid, the chamber closing sign will appear.
   • Insert the two hooks into the appliance first, and then push the lid against the main unit.
   • The appliance will not start working if the chamber lid is not properly closed. During the pasta-making process, if you open the chamber lid, the appliance will stop working. Assemble the lid and press the Start/pause button to start the operation again.
   • When the lid is closed, the needed amount of liquid is displayed.
   • Use the supplied water cup to measure the amount of liquid according to the indication on the display.

Important!

The pasta recipes provided in the recipe book have been tested for success. If you experiment with or use other pasta recipes, the flour and water/egg ratios will need to be adjusted. The pasta maker will not operate successfully if you do not adjust the new recipe accordingly.

Note

• To ensure the quality of the pasta, use gluten flour to make pasta. Follow the recommended proportion to add the ingredients. yy Seasonal changes and using ingredients from different regions may affect the
  flour/water ratio. You may adjust based on the recommended proportion.

• When making egg pasta or vegetable pasta, make sure you whisk the egg mixture or vegetable juice evenly with the water before pouring it into the chamber through the slot in the lid. When adding ingredients, make sure the ingredient is in a liquid form.

• See the recipe book provided for additional pasta recipe variations.

• When making gluten-free pasta/noodles or cookies, do not follow the recommended liquid amount indicated by the appliance.

Cleaning

1. Disconnect the plug from the power outlet.

2. Remove the mixing chamber lid. (Fig. 3)

3. Loosen the front panel control knobs. (Fig. 4)
   Note: The front panel is heavy. Take extra caution when removing it.

4. Disassemble the front panel, the shaping disc, the shaping disc holder, the mixing paddle, and the mixing chamber in order. (Fig. 5)

5. Use a dry cloth to clean the flour residue on the main unit.

6. Clean the shaping disc with the supplied cleaning tool to remove the dough residues.
   After that, you can clean it with water.
   Note: For the spaghetti, thick spaghetti, angel hair, and fettuccine shaping discs, let the discs air-dry for 2 to 4 hours. Then use the corresponding cleaning tool to poke out the dough in the holes.

7. Clean all detachable parts, and wipe them dry. (Fig. 6)

8. Use a dry cloth to clean the control panel and the exterior of the pasta maker.

Storage

1. Unplug the appliance and let it cool down.
   Note: Make sure all parts are clean and dry before storing.

2. You can store the shaping discs in the storage drawer.

Troubleshooting

This chapter summarizes the most common problems you could encounter with the appliance. If you are unable to solve the problem with the information below, visit www.philips.com/support for a list of frequently asked questions or contact the Consumer Care Center in your country.

Check whether the power plug is plugged correctly and the outlet is working properly.
After pressing the On/off button the appliance sounds but does not work.| The mixing chamber, the shaping disc, or the front panel is assembled incorrectly.| Make sure you follow the user manual to assemble all parts correctly.
The safety switch is triggered and the appliance suddenly stopped or suddenly restarts during the processing.| The front panel knob is loose.| Make sure the front panel is securely assembled.

Excessive ingredients in the pasta maker.

| The maximum amount of flour used for each batch is 600g. If more than 600g is added, reduce the amount of flour before next batch.
During processing, the appliance stops working when you open the lid.| For safety reasons, the appliance always stops working when

the lid is opened during processing.

|

If you need to resume the previous operation, close the lid properly, and press the Start/pause button.

During processing, the appliance stops. There is no alarm sound or flashes.

|

The pasta maker has overheated due to long continuous working time.

| Disconnect from the power source, and allow the pasta maker to cool down. To better protect the lifetime of the appliance, the continuous working time should be less than 45 minutes. You can restart using the appliance after 15 minutes of rest.
When weighing the flour, the weight shown on the screen changes all the time.| You are touching the appliance or the power cord.| When the appliance is weighing the flour, do not touch the appliance or the power cord.
A small amount of water is leaking out from the appliance.| Water is added before the program starts.| Follow the user manual instructions to add water right after the program starts.

Unable to make pasta successfully with the liquid calculation function.

| The required liquid amount indicated on the display screen does not apply to some recipes (for example cookies, and gluten-free pasta).|

These recipes require you to skip the liquid calculation part. In this case, press the Start/pause button for 5 seconds, and the appliance will start mixing and extruding directly.

E1 displays on the screen.

| ****

The shaping disc is not attached.

| Attach the disc holder to the main unit, attach the shaping disc properly, and fix the front panel properly to the device.
The lid is not in place or not properly attached.| Attach the lid properly.
The appliance stops during processing,

E2 displays on the screen, the indicators are flashing quickly, and the alarm sounds.

| The mixing paddle may be blocked by some foreign objects.| ****

Disconnect from the power source, clean the pasta maker, and follow the user manual again to restart the pasta making.

The dough may be too dry.
The wrong program is selected.
EEE displays on the screen.| The appliance malfunctions.| Contact the service center.

FAQ’s

What types of pasta can I make with the Philips HR2382 Pasta Maker Machine?

The Philips HR2382 Pasta Maker Machine can make a variety of pasta types, including spaghetti, fettuccine, penne, lasagne, and even Asian noodles like udon and soba.

How long does it take to make pasta with the Philips HR2382 Pasta Maker Machine?

The time it takes to make pasta with the Philips HR2382 Pasta Maker Machine varies depending on the type of pasta you’re making, but on average, it takes about 15-20 minutes.

Can I make gluten-free pasta with the Philips HR2382 Pasta Maker Machine?

Yes, you can make gluten-free pasta with the Philips HR2382 Pasta Maker Machine. Simply use gluten-free flour instead of regular flour.

Is the Philips HR2382 Pasta Maker Machine easy to clean?

Yes, the Philips HR2382 Pasta Maker Machine is easy to clean. The parts are dishwasher safe, and the machine comes with a cleaning tool to make cleaning even easier.

Can I make pasta dough ahead of time with the Philips HR2382 Pasta Maker Machine?

Yes, you can make pasta dough ahead of time with the Philips HR2382 Pasta Maker Machine. Simply store the dough in an airtight container in the refrigerator until you’re ready to use it.

Does the Philips HR2382 Pasta Maker Machine come with any recipes?

Yes, the Philips HR2382 Pasta Maker Machine comes with a recipe book that includes a variety of pasta recipes.

How much pasta can the Philips HR2382 Pasta Maker Machine make at once?

The Philips HR2382 Pasta Maker Machine can make up to 600g of pasta at once, which is enough for about 4-6 servings.

What is the warranty for the Philips HR2382 Pasta Maker Machine?

The Philips HR2382 Pasta Maker Machine comes with a 2-year warranty.

What is the maximum amount of flour that can be used in the pasta maker?

The maximum amount of flour that can be used for each batch is 600g.

What should I do if the indicators do not light up when I turn on the pasta maker?

Check whether the power plug is plugged correctly and the outlet is working properly.

How do I clean the shaping disc?

Use the supplied cleaning tool to remove the dough residues, and then clean it with water.

How do I assemble the pasta maker before use?

Push the mixing chamber into the appliance, insert the mixing paddle all the way into the main unit, attach the disc holder to the appliance, put the shaping disc onto the disc holder, and make sure it is firmly fixed on the disc holder. Attach the front panel to the main unit, and fasten the front panel control knobs.

What should I do if the appliance suddenly stops or suddenly restarts during processing?

Make sure the front panel is securely assembled.

How do I use the skip-scaling function?

Press and hold the Start/pause button for 5 seconds.

What should I do if E1 displays on the screen?

Attach the disc holder to the main unit, attach the shaping disc properly, and fix the front panel properly to the device.

Download this PDF Link:Philips HR2382 Pasta Maker Machine User Manual

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>