NYKO NYK89501 Power Pak Portable Battery User Manual

NYKO NYK89501 Power Pak Portable Battery

Welcome!

Thank you for purchasing the Nyko Power Pak'” external battery for Steam Deck'”. We hope this purchase allows you to stretch your gaming sessions by an hour or more when you are unable to recharge your console via AC power. Keep in mind the Steam Deck is a power hungry beast so your battery life will depend on which settings you are using in your games. To optimize battery life it is recommended you adjust game settings such as frame rate, refresh rate, screen brightness, and graphic quality settings.

At a Glance

1. USB-C 37W MAX PD Power Output
2. USB-C 30W MAX PD Power Input
3. LED Charge Indicators
4. Power I Charge Status Button
5. 10000mAh/3.7V LiPo Battery
6. Spring Loaded Grip Clamp

Checking Your Power Pak™ Charging Status

Track battery power at a glance with the integrated four-light LED status indicator. Press the power/charge-status button on your Power Pak and the LEDs will indicate its charge level. Four LEDs means the Power Pak battery is fully charged, while one LED means it’s almost empty.

Before Using Your Power Pak™

IMPORTANT : Before using your Power Pak battery for the first time, fully charge it (so that pressing the power/charge status button lights all 4 status LEDs). Connect your official Steam Deck power supply to the Power Pak to begin charging.

Important Safety Instructions

• Read all the instructions before using the product
• To reduce the risk of injury, close supervision is necessary when the product is used near children
• Do not disassemble the Power Pak. Incorrect reassembly may result in a risk of fire or injury to persons.
• The maximum operating temperature is 0° to 60° C.
• Do not expose Power Pak to rain or snow.
• Do not use a Power Pak that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion or risk of injury.
• We recommend using a 45W PD (Power Delivery) charger (not included) to charge the Power Pak'”.
• Do not charge the Power Pak'” while it is plugged into the Steam Deck'”.
• Overheating Protection – If all four LEDs on the Power Pak'” are quickly flashing, it is to indicate the battery has temporarily stopped charging to prevent overheating.
• Do not expose Power Pak to fire or excessive temperature. Exposure to fire or temperature over 100·c (212°F) may cause explosion
• Use of a power supply not recommended or sold by the manufacturer may result in a risk of fire, electric shock, or injury to persons.

Power Pak™ Usage

1. Align the ports on the Power Pak to the center holes on top of the Steam Deck'”.
2. Push the bottom clamp against the body of the Steam Deck'” until it opens up and grips onto the bottom of the console.
3. Insert the USB-C cable from the Power Pak into the Steam Deck'”.
4. The Power Pak will turn on and begin charging your Steam Deck'”.
5. The Power Pak will turn off when unplugged from the Steam Deck'”.
6. You can also turn off the Power Pak by holding down the power/charge status button for 3 seconds.
   NOTICE : Power Pak does not support high-power charging cables with Emarker chips. When using the Power Pak it is normal that the Steam Deck dashboard will show incorrect and fluctuating estimated charging times. This will vary depending on the power demands of the game you are playing.

Specification

• Model 89501 Nyko Power Pak for Steam Deck
• Capacity 10,000mAh/3.7V/37wh
• Type-C Input 5V /3A, 9V /3A, 12V /2.5A, 15V /2 A (30W MAX)
• Type-C Output 5V/3A, 9V /3A,12V/2.5A,15V/ 2.46A (37W MAX)
• Dimensions 160 x 122.8 x 45.4 mm
• Weight 294g

Power Pak normal operating temperature is between 0~60°C. Overheating protection will engage if the temperature rises above 60°C and LEDs will blink quickly. Power Pak will resume charging when the temperature drops below 55°C. Over-currrent protection will engage when the current exceeds the maximum current of 0.5A and battery will stop discharging. Short circuit protection will engage if the output positive and negative terminals are short circuited; the battery will start protection and stop discharge.

Exclusions & Limitations

Except for the limited warranty expressly set forth or to the extent restricted or prohibited by applicable law, Nyko expressly disclaims any and all other warranties expressed or implied, including any warranty of quality, merchantability, or fitness for a particular purpose, and you specifically agree that Nyko shall not be liable for any special, incidental, indirect, punitive, or consequential damages for breach of any warranty of any type on any Nyko product. In addition to and without limiting the generality of the foregoing disclaimers, the limited warranty does not, under any circumstances, cover the replacement or cost of any electronic device or personal property inside or outside of the Nyko product.

FCC Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:

1.  this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.
   Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

• Changes or modifications to this product not authorized by Nyko could void the electromagnetic compatibility (EMC) and wireless compliance and negate your authority to operate the product.
  This product has demonstrated EMC compliance under conditions that included the use of compliant peripheral devices and shielded cables between system components. It is important that you use compliant peripheral devices and shielded cables between system components to reduce the possibility of causing interference to radios, television sets, and other electronic devices. Exposure to radio frequency energy. The radiated output power of this device meets the limits of FCC/IC radio frequency exposure limits. This device should be operated with a minimum separation
  distance of 20 cm (8 inches) between the equipment and a person’s body.

• The following importer is the responsible party:
  Company Name: Nyko Technologies
  Address: 1642 Westwood Blvd., Suite 300, Los Angeles, CA, 90024, USA
  Telephone: + 1(310) 446-6602

Customer Service

• 90-day limited warranty*
• Lifetime technical support
• customersupport@nyko.com
• (US) + 1-310-446-6602 ext.009
• Note that your rights under applicable law governing the sale of consumer goods remain unaffected by the warranties given by this Limited Warranty.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>