SUPERLED DALI-2 CCT 96W DALI DT8 Dimmable LED Driver Instructions

SUPERLED DALI-2 CCT 96W DALI DT8 Dimmable LED Driver

Product Information

The 96W DALI DT8 Dimmable LED Driver is a product that allows for dimming of LED lights through the use of DALI/Push signal input. It has a digital display and push dim function. The product has a common anode output with four LED channels. It has a rated power of a maximum 96W and can operate within a voltage range of 100-277V AC. The product has an input power factor of >0.90 @ 230VAC and a total harmonic distortion of 15% (@ full load / 230VAC). The efficiency of the product is 90% @ 230VAC full load with an AC current of 1.2A @ 100VAC, 0.5A @ 230VAC.

Product Usage Instructions

1. Read the instructions carefully before installation.
2. Connect the DALI/Push signal input to the product.
3. Connect the LED output to the common anode output with four LED channels.
4. Connect the input power to the product within the voltage range of 100-277V AC.
5. Turn on the product using the switch.
6. Use the push dim function to adjust the brightness of the LED lights.

Important: Read All Instructions Prior to Installation

Function introduction

Product Data

Output

| LED Channel| 4
---|---|---
DC Voltage| 24V DC
Max. Current| Max. 4A/CH, CH1+CH2+CH3+CH4=4A
Voltage Tolerance| ±1%
Rated Power| max. 96W

Input

| Voltage Range| 100-277V AC
Frequency Range| 50/60Hz
Power Factor ( Typ.)| > 0.90 @ 230VAC
Total Harmonic Distortion| THD ≤ 15% (@ full load / 230VAC)
Efficiency (Typ.)| 90% @ 230VAC full load
AC Current (Typ.)| 1.2A @ 100VAC, 0.5A @ 230VAC
Inrush Current (Typ.)| COLD START Max. 50A @ 230VAC
Leakage Current| < 0.5mA /230VAC

Control

| Dimming Interface| DALI DT8 (DALI consumption<2mA)/Push
Dimming Range| 0.1%-100%
Dimming Method| Pulse Width Modulation
Dimming Curve| Logarithmic

Protection

| Over Current| Yes, recovers automatically after fault condition is removed
Over Temperature| Yes, recovers automatically after fault condition is removed

Environment

| Working Temp.| -20℃ ~ +50℃
---|---|---
Max. Case Temp.| 75℃ (Ta=”45℃”)
Working Humidity| 10% ~ 95% RH non-condensing
Storage Temp. & Humidity| -40℃ ~ +80℃, 10% ~ 95% RH

Safety & EMC

| Safety Standards| UL8750, CAN/CSA C22.2 No. 250.13-14,

EN61347-1, EN61347-2-13 approved

Withstand Voltage| I/P-O/P: 3.75KVAC
Isolation Resistance| I/P-O/P: 100M Ohms / 500VDC / 25℃ / 70% RH
EMC Emission| EN55015,  EN61000-3-2,  EN61000-3-3
EMC Immunity| EN61547, EN61000-4-2,3,4,5,6,8,11, , surge immunity Line-Line 1KV

Others

|

MTBF

| 189200H, MIL-HDBK-217F @ 230VAC full load and 25℃ ambient temperature
Dimension| 2446432mm (LWH)

• Dimmable LED driver, max. output power 96W total
• In compliance with IC 62386-101:2014, IC 62386-102:2014, IC 62386-207 Ed2, IC 62386-209:2011
• Built-in DALI-2 interface, DALI DT8 device
• 100-277VAC wide input voltage
• 4 channels DC 24V constant voltage output
• Class II power supply, full isolated plastic case
• High power factor and efficiency
• DALI DT8 device, each device is controlled via a single DALI address
• Any one of three DT8 color types RGBW, XY Coordinate, Tc can be preset by factory setting
• Color control according to DALI specifications of device type 8
• Compatible with universal DALI masters that support DT8 commands
• IP20 rating, suitable for indoor LED lighting applications

Warranty

• 5 years warranty

Safety & Warnings

• DO NOT install with power applied to the device.
• DO NOT expose the device to moisture.

Operation

Set DALI Address Manually Via Buttons

1. Press and hold down any of the two buttons until the numeric digital display flashes, then release the button.
2. Click any of the two buttons once to select a digit, click again to change the digit until the desired DALI address appears. Click first button to set the “tens” position and second button to set “units” position. The address can be set from 00~63.
3. Then press and hold down any of the 2 buttons until the numeric digital display stops flashing to confirm the setting.

Note: DALI address can be manually assigned from 00-63-FF. by factory defaults. no DALI address is assigned for the dimmer, and the display shows . Setting DALI address as will reset the dimmer to factory defaults.

DALI Address Assigned by DALI Masters

• DALI address can also be assigned by DALI Master controller automatically, please refer to user manuals of compatible DALI Masters for specific operations.

Note: The digital display will show When the DALI master is assigning addresses.

1. Once an address is selected, all four channels’ address will be the same. For example, if the dimmer is addressed to 22 on the display then Ch1, Ch2, Ch3 and Ch4 will be the same address 22.

PUSH Dimmer Mode

While connected with a AC PUSH, the digital display will show “PD” which means Push Dimmer Mode, operations under Push Dimmer Mode are as follows:

1. Click the button to switch ON/OFF
2. Press and hold down the button to increase or decrease light intensity to desired level and release it, then repeat the operation to adjust light intensity to opposite direction.
3. Memory function after power off or power failure enables the device to memorize the status before power off while power on again.

Wiring diagram

With DALI Bus

1. When Preset Color Type is RGBW or XY coordinates.

Note

1. DT8 color type of the driver can be RGBW or XY coordinates, which can be preset by factory setting.
2. For color type XY coordinates, the 4th W channel can only be controlled together with GB channels.
3. Only when the coordinate point at the area where R, G, B three colors mix color will W channel turn on.
4. W channel intensity will go up only as R, G, B three colors’ intensity goes up simultaneously.
5. W channel intensity will go down only as R, G, B three colors’ intensity goes down simultaneously.
6. If controlled by XY type touch panel, use W button on the panel to mix RGB thus turn on 4th channel W.

When Preset Color Type is Tc

With Push Dimmer

Product Dimension

Installation

Fixing Screw Holes

Documents / Resources

| SUPERLED DALI-2 CCT 96W DALI DT8 Dimmable LED Driver [pdf] Instructions
DALI-2 CCT 96W DALI DT8 Dimmable LED Driver, DALI-2, CCT 96W DALI DT8 Dimmable LED Driver, Dimmable LED Driver, LED Driver, Driver
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>