EGO POWER PAD5000 56 Volt Power Inverter User Manual

PAD5000 56 Volt Power Inverter
User Manual OPERATOR’S MANUAL
56-VOLT POWER INVERTER
MODEL NUMBER PAD5000/ PAD5000-FC

PAD5000 56 Volt Power Inverter

WARNING: To reduce the risk of injury, the user must read and understand the Operator’s Manual before using this product. Save these instructions for future reference.

READ ALL INSTRUCTIONS!
READ & UNDERSTAND OPERATOR’S MANUAL
WARNING: To reduce the risk of injury, fire, electric shock, user must read and understand the operator’s manual for their USB accessories and AC devices in addition to this instruction sheet. Ensure compatibility before using the power inverter. Do not use this product if any part is damaged or missing.

FCC STATEMENT

1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

2. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

SAFETY SYMBOLS

The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols and the explanations with them deserve your careful  attention and understanding. The symbol warnings do not, by themselves, eliminate any danger. The instructions and warnings they give are no  substitutes for proper accident prevention measures.
WARNING: Be sure to read and understand all safety instructions in this Operator’s Manual, including all safety alert symbols such as “DANGER,” “WARNING,” and “CAUTION” before using this product. Failure to following all instructions listed below may result in electric shock, fire, and/or serious personal injury.
SYMBOL MEANING
SAFETY ALERT SYMBOL: Indicates DANGER, WARNING, OR CAUTION. May be used in conjunction with other symbols or pictographs.

SAFETY INSTRUCTIONS

This page depicts and describes safety symbols that may appear on this product. Read, understand, and follow all instructions on the machine before attempting to assemble and operate it.

| Safety Alert| Indicates a potential personal injury hazard.
---|---|---
| Read & Understand Operator’s Manual| To reduce the risk of injury, user must read and understand the  operator’s manual before using this product.
V| Volt| Voltage
A| Amperes| Current
lb| Pound| Weight
kg| Kilogram| Weight
| Alternating Current| Type or a characteristic of current
| Direct Current| Type or a characteristic of current

IMPORTANT SAFETY INSTRUCTIONS
WARNING: When using this product, basic precautions should always be followed, including the following:

• Read all the instructions before using the product.
• To reduce the risk of injury, close supervision is necessary when the product is used near children.
• Do not put fingers or hands into the product.
• Use of an attachment not recommended or sold by power pack (inverter) manufacturer may result in a risk of fire, electric shock, or injury to persons.
• To reduce risk of damage to the electric plug and cord, pull the plug rather than the cord when disconnecting the power pack (inverter).
• Do not use a battery pack or appliance that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion, or risk of injury.
• Do not operate the power pack (inverter) with a damaged cord or plug, or a damaged output cable.
• Do not disassemble the power pack (inverter), take it to a qualified service person when service or repair is required. Incorrect reassembly may result in a risk of fire or electric shock.
• To reduce the risk of electric shock, unplug the power pack (inverter) form the outlet before attempting any instructed servicing.

WARNING: RISK OF EXPLOSIVE GASES

• To reduce risk of battery explosion, follow these instructions and those published by battery manufacturer and manufacturer of the equipment you  intend to use in vicinity of the battery. Review cautionary marking on these products.

PERSONAL PRECAUTIONS

• NEVER smoke or allow a spark or flame in vicinity of battery.
• Be extra cautious to reduce risk of dropping a metal tool onto battery. It might spark or short circuit battery or other electrical part that may cause explosion.
• When charging the internal battery, work in a well ventilated area and do not restrict ventilation in any way.
• Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.
• Have plenty of fresh water and soap nearby in case battery acid contacts skin, clothing, or eyes.
• Wear complete eye protection and clothing protection. Avoid touching eyes while working near battery.
• If battery acid contacts skin or clothing, wash immediately with soap and water. If acid enters eye, immediately flood eye with running cold water for at least 10 minutes and get medical attention immediately
• Do not expose a power pack (inverter) to fire or excessive temperature. Exposure to fire or temperature above 265 °F (130°) may cause explosion.
• Have servicing performed by a qualified repair person using only identical replacement parts. This will ensure that the safety of the product is maintained.

WARNING: Read all safety warnings and instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference

• Risk of fire and electric shock. Dry location use only. Do not expose the power inverter to rain or wet conditions. Water entering the power inverter  will increase the risk of electric shock.
• For household use only.
• Do not allow the power inverter to be used as a toy. Close attention is necessary when used by or near children.
• The power inverter is not intended for any use other than charging small USB electronics or small AC devices specified in SPECIFICATIONS in  this manual. Any other use may result in damage.
• Do not put fingers or hands into the power inverter.
• Switch off the power inverter when not in use.
• Prevent unintentional starting. Ensure the switch is in the off-position before connecting to battery pack, picking up or carrying the power inverter. Carrying the power inverter with your finger on the switch or energizing power inverter that has the switch on invites accidents.
• Disconnect the battery pack from the power inverter before making any adjustments, changing accessories, or storing power inverter. Such preventive safety measures reduce the risk of starting the power inverter accidentally.
• Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.
• Use power inverter only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.
• Use only with the battery packs and chargers listed below:
  BATTERY PACK| CHARGER
  ---|---
  BA1400, BA1400-FC, BA2800, BA2800-FC,
  BA4200, BA4200-FC, BA1400T, BA1400T-FC,
  BA2242T, BA2242T-FC, BA2800T, BA2800T-FC,
  BA3360T, BA3360T-FC, BA4200T, BA4200T-FC,
  BA5600T, BA5600T-FC, BA6720T, BA6720T-FC| CH2100, CH2100-FC,
  CH3200, CH3200-FC,
  CH5500, CH5500-FC,
  CH2800D, CH2800D-FC,
  CH7000, CH7000-FC
• When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.
• Do not use a battery pack or power inverter that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion, or risk of injury.
• Follow all charging instructions and do not charge the battery pack or appliance outside of the temperature range specified in the instructions. Charging improperly or at temperatures outside of the specified range may damage the battery and increase the risk of fire.
• Do not modify or attempt to repair the power inverter or the battery pack except as indicated in the instructions for use and care.
• Store idle power inverter out of the reach of children and do not allow persons unfamiliar with the power inverter or these instructions to operate the power inverter. Power inverters are dangerous in the hands of untrained users.
• Maintain power inverter and accessories. Check for misalignment or breakage of parts and any other condition that may affect the power inverter’s operation. If damaged, have the power inverter repaired before use. Many accidents are caused by poorly maintained power inverter.
• Save these instructions. Refer to them frequently and use them to instruct others who may use this product. If you loan someone this product, loan them these instructions also.

SAVE THESE INSTRUCTIONS!

INTRODUCTION

Congratulations on your selection of a new generation of 56V Lithium-ion power inverter. It has been designed, engineered and manufactured to give you the best possible dependability and performance.
Should you experience any problem you cannot easily remedy, please contact EGO customer service center 1-855-EGO-5656.
This manual contains important information on to the safe assembly, operation and maintenance of your power inverter. Read it carefully before using  the power inverter.
Keep this manual handy so you can refer to it at any time.
SERIAL NUMBER ____ DATE OF PURCHASE
YOU SHOULD RECORD BOTH SERIAL NUMBER AND DATE OF PURCHASE AND KEEP IN A SAFE PLACE FOR FUTURE REFERENCE

SPECIFICATIONS

second
Weight (Without battery pack)| 3.3 lb. (1.5 kg)
Recommended Ambient Temperature Range for Operation| 41°F – 104°F (5°C – 40°C)
Recommended Ambient Temperature Range for Storage| -4°F -158°F (-20°C – 70°C)
Recommended Ambient Temperature Range for Charging| 41°F – 104°F (5°C – 40°C)

PACKING LIST

DESCRIPTION

KNOW YOUR POWER INVERTER (Fig. 1)
The safe use of this product requires an understanding of the information on the product and in this operator’s manual, as well as knowledge of the project you are attempting. Before using this product, familiarize yourself with all operating features and safety rules. POWER BUTTON (with LED Indicator)
To switch the power inverter on/off and indicate the power inverter working status.
AC and USB PORTS
To connect with AC and USB port devices.

OPERATION

WARNING: Do not allow familiarity with this product to make you careless. Remember that a careless fraction of a second is sufficient to inflict serious injury.
WARNING: Do not modify or attempt to repair the power inverter except as indicated in the instructions for use and care.
WARNING: This device is intended to be used indoors only. Do not use outdoors under any conditions.

APPLICATIONS
You may use the power inverter for the following purposes:

• Supplying power for operating compatible small USB electronics or small AC devices, such as cell phones, tablets, laptops, LED lights, small fans, radios, etc.
• Charging the EGO battery using the inverter USB-C input/output port 2, such as USB PD chargers.
• Providing light in low light conditions or emergency backup.

INSTALLING/REMOVING BATTERY PACK (Fig. 2 & 3)
NOTE: Fully charge the battery pack before first use.
To Install Battery Pack (Fig. 2)
Slide a battery pack onto the power inverter as shown. Make sure the latch on the battery pack snaps into place and the battery pack is secured in the power inverter before beginning operation.
To Remove Battery Pack (Fig. 3)
Press the battery-release button, the battery pack will disengage from the latch. Pull the battery pack away from the power inverter.

WARNING: Always be aware of the location of your feet, children, or pets when pressing the battery-release button. NEVER remove the battery pack at a high position.
WARNING: Always remove the battery when the power inverter is not in use.

TO START/STOP THE POWER INVERTER (FIG. 4)

1. Install the battery pack.
2. To turn the power inverter ON, press and hold the power button for more than half a second. The button will illuminate green to indicate that the power inverter is active.
3. To turn the power inverter OFF, press and hold the power button for more than half a second again. The green light will be off to indicate that the  power inverter is deactivated.

LED LIGHTS (FIG. 5 )
Your power inverter is equipped with two LED lights located on the bottom of the unit. These lights provide illumination of low light areas.
To use the LED lights, press the LED button to scroll through the following light modes:

•  Low brightness mode
• High brightness mode
• LED lights are turned off

In any mode, press and hold the LED button for more than 1 second and the lights will switch into flashing, “EMERGENCY” mode.
NOTE: The power inverter must be turned ON for the LED lights to function.

POWER BUTTON LED INDICATOR
The power button features an LED indicator that communicates the working condition of the power inverter as follows:

Power Button LED Indicator| Power Inverter Working condition| LED Indicator on Battery Pack
---|---|---
Solid green| | Standby| 1. For EGO battery packs BA1400, BA1400-FC, BA2800, BA2800-FC, BA4200, and BA4200-FC

Flashing GREEN, RED and ORANGE alternately

2. For EGO battery packs BA1400T, BA1400T-FC, BA2242T, BA2242T-FC, BA2800T, BA2800T-FC, BA3360T, BA3360T-FC, BA4200T, BA4200T-FC, BA5600T, BA5600T-FC, BA6720T, BA6720T-FC
Last LED flashing GREEN, the former LEDs shining solid GREEN.
OR shining solid GREEN according to battery capacity.
The battery will fresh LED indicator every 1-2 minutes to update the real-time fuel gauge.

Green light gradually fading in and out| | Powering connected devices
Orange light gradually fading in and out| | Charging the battery pack
Green and orange lights alternately fading in and out| | Powering connected devices AND charging the battery pack
Flashing green, 1 flash every second| | Low battery voltage. See “ LOW BATTERY PACK CHARGE PROTECTION”

below.

Solid red for 1 minute| | The power inverter or battery pack is overheated. Allow the unit to cool down, then restart the inverter. See “ OVER TEMPERATURE PROTECTION ” below.
Flashing red for 1 minute, 1 flash every 0.5 seconds| | The power inverter may be overloaded or short-circuited. Disconnect device from the AC output port, see “ OVERLOAD OR SHORT CIRCUIT PROTECTION ” below.
Flashing red for 1 minute, 1 flash every second| | Other electronics error. Disconnect your device and reconnect it again, if the same fault reoccurs, please contact EGO customer service center.

OVER TEMPERATURE PROTECTION
If the battery or inverter temperature exceeds 158°F (70°C) during operation, the temperature-protection circuit will shut off the unit in 1 minute to protect from overheating damage. The power button indicator will glow solid red for 1 minute. Allow the unit to cool until its temperature drops below 152°F (67°C) before restarting.

LOW BATTERY PACK CHARGE PROTECTION
The inverter automatically shuts down 1 minute after the battery pack charge reached a low level.
Charge the battery pack.
OVERLOAD OR SHORT CIRCUIT PROTECTION
When the connected AC device draws more than the rated power of the port, the inverter LED indicator will flash red for 1 minute at 1 flash every 0.5 seconds. Then the inverter will automatically shut down. Disconnect the AC device.

USING WITH EXTERNAL DEVICES
When a charged battery pack is installed, the power inverter converts DC electricity to 120V AC household power and/or USB-A (5/9/12V, up to 18 W)  or USB-C output port 1 (5/9/12/15/20V, up to 18 W) or USB-C input/output port 2 (5/9/12/15/20V, up to 100 W) supply power, allowing the user to  charge and power a variety of devices.
Additionally the power inverter can charge the EGO battery when a USB PD charger is connected to the USB-C  input/output port 2 (5/9/12/15/20V, up to 100 W).

NOTE: The inverter may not be compatible for use with some USB PD chargers.
WARNING: Risk of electric shock. When using a grounded appliance, the product will not provide an electrical path to earth ground. Do not power devices with damaged or frayed power cords.
WARNING: To avoid a risk of electric shock, do not insert a nail, wire, etc. into the AC output port.
WARNING: Risk of electric shock and risk of fire. This device is not to be stored or kept in a vehicle.

1. Insert a battery pack into the power inverter.
2. Press and hold the power button for more than half a second to turn the inverter ON. The LED in the power button will illuminate green when the inverter is ready to use.
3. Plug devices you want to power or charge into the power inverter’s USB ports and/or 120 volt AC output port. The power inverter will begin charging/powering the devices automatically.
4. Or plug compatible USB PD charger into the inverter’s USB-C input/output port 2 to charge the EGO battery installed on the inverter, then plug  the other end of the charger into household outlet.
5. When the power inverter is not in use, disconnect the devices from the inverter, then press and hold the power button for more than half a second to turn it OFF.
6. Remove the battery pack from the power inverter.

NOTE:

• Runtime of the connected device is dependent upon the device and the EGO battery capacity.
• Charging time of the EGO battery pack is dependent upon the USB PD charger.
• The power inverter may get warm. This is part of the normal operation of the power inverter.
• Always use the power inverter in a well-ventilated area.
• Do not insert a nail, wire, etc. into the USB ports. Otherwise a short circuit may damage the USB ports.
• When switching on the power inverter, if the USB output current is less than 100mA and the AC output power is less than 10W, the system will shut  off automatically in 2 hours.

MAINTENANCE

WARNING: To avoid serious personal injury, always remove the battery pack from the power inverter when cleaning or performing any maintenance.
WARNING: When servicing, use only identical EGO replacement parts. Use of any other parts may create a hazard or cause product damage. To ensure safety and reliability, all repairs should be performed by a qualified service technician.

GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged  by their use. Use a clean cloth to remove dirt, dust, oil, grease, etc.
WARNING: Do not at any time allow brake fluids, gasoline, petroleum-based products, penetrating oils, etc. to come in contact with plastic parts. Chemicals can damage, weaken or destroy plastic which may result in serious personal injury.
STORING THE UNIT

• Remove the battery pack from the power inverter.
• Clean the power inverter thoroughly before storing it.
• Store the unit in a dry, well-ventilated area, locked-up or up high, out of the reach of children. Do not store the unit on or adjacent to fertilizers,  gasoline, or other chemicals.

TROUBLESHOOTING

◾ Cool the battery pack until its temperature drops below 152°F (67°C).
Power button LED flashes green at 1 flash every second.| Low battery pack charge.| Charge the battery pack.
Power button LED flashes red for 1 minute at 1 flash every 0.5 second, then shuts off.| The power inverter may be overloaded or short-circuit.| Remove the AC device and turn the power inverter
on again, see the section “ OVERLOAD OR SHORT CIRCUIT PROTECTION ”.
Power button LED glows solid red for 1 minute, then shuts off.| The inverter or battery pack is too heated.| The power inverter or battery pack is overheated. Allow the unit to cool down, then restart the inverter. See the section “ OVER TEMPERATURE PROTECTION “.
Power button LED flashes red for 1 minute at 1 flash every second, then shuts off.| Other electronics error.| Disconnect your device and reconnect it again, if the same fault reoccurs, please contact EGO customer service center.
The inverter cannot discharge when using USB-C ports 1 or 2.| No electronics communication between the inverter and the external devices connected to USB-C ports 1 or 2.| ◾ Remove the external devices and re-insert them OR
◾ Turn OFF the inverter and restart it.
PROBLEM| CAUSE| SOLUTION
---|---|---
Green light does not gradually fade in and out when powering a device connected to AC  output port.| AC output port power is less than 10W.| This is normal operation. No action is needed.

EGO LIMITED WARRANTY

WARRANTY POLICY TERMS AND DURATION
Chevron North America, Inc. (“Chevron North America”) provides the following Limited Warranty for EGO products to the original purchaser of EGO products.
The detailed warranty period for each EGO product can be found online at http://egopowerplus.com/warranty-policy.
Please contact EGO Customer Service Toll-Free at 1-855-EGO-5656 any time you have questions or warranty claims or would like a hard copy of the warranty.

LIMITED SERVICE WARRANTY
EGO products are warranted against defects in material or workmanship from the date of original retail purchase for the applicable warranty period. For  any properly and timely submitted warranty claim, if Chevron North America determines a product to be defective during the warranty period, the  product will receive free repair or replacement as determined by Chevron North America.

HOW TO OBTAIN SERVICE
For warranty service, within the applicable warranty period, please contact EGO customer service toll-free at 1-855-EGO-5656. When requesting warranty service, you must present the original dated sales receipt. An authorized service center will be selected to evaluate and repair the product if  defective according to the stated warranty terms. When bringing your product to the authorized service center, there may be a small deposit that will be  required when dropping off your tool. This deposit is refundable when the repair service is deemed to be covered under warranty.

ADDITIONAL LIMITATIONS & EXCLUSIONS
This limited warranty applies only to the original purchaser from an authorized EGO retailer and is not transferable. EGO products shall not be considered defective, and this warranty will not apply, where the claimed defect is attributable to any cause other than the above-defined defects. This warranty shall be void if the product has been used for rental purposes. This warranty shall not apply to damage caused by accident, abuse, misuse, alteration, modification, unauthorized repair, liquid contact, fire, earthquake or other external cause; operating the product outside EGO’s instructions, specifications or guidelines; or failure to properly service of maintain the product. This warranty also does not apply to cosmetic damage, including but  not limited to scratches or dents; defects caused by normal wear and tear or otherwise due to the normal aging of the product.
THIS EXPRESS WARRANTY IS GIVEN IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY WARRANTIES OF MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSE OR USE, WHICH ARE DISCLAIMED. Any implied warranties, including warranties of merchantability or fitness for a particular purpose, that cannot be disclaimed under state law are limited to the applicable warranty period defined at the beginning of this article. The sole and exclusive remedy in connection with the purchase, installation, use, and/or performance of the EGO products is repair or replacement of the product as determined by Chevron North America. Chevron North America’s maximum liability shall not in any case exceed the purchase price paid for the product. CHERVON NORTH AMERICA SHALL NOT BE LIABLE TO THE USER OR TO ANYONE ELSE FOR CONSEQUENTIAL, INCIDENTAL, SPECIAL, EXEMPLARY, INDIRECT, OR PUNITIVE DAMAGES ARISING FROM USE OF THE PRODUCTS, INCLUDING BUT NOT LIMITED TO PERSONAL INJURY, DEATH, PROPERTY DAMAGE, LOST PROFITS, OR OTHER ECONOMIC INJURY. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Some states do not allow limitations on how long an implied warranty lasts, the exclusion or limitation of incidental or consequential damages, or the limitations on time to bring certain actions, so such limitations contained herein do not apply to individual consumers in those states.

This warranty is subject to and shall be interpreted according to Michigan law without regard to principles of conflicts of laws. No legal action shall be brought against Chevron North America unless filed within one (1) year after the basis for such legal action becomes known, or with the exercise of reasonable diligence should have become known. Any action not timely filed shall be deemed waived.
For customer service contact us toll-free at: 1-855-EGO-5656 or EGOPOWERPLUS.COM.

EGO Customer Service
769 Seward Ave. NW, Suite 102
Grand Rapids, Michigan 49504.

References

• The #1 Rated Brand in Cordless Outdoor Power Equipment | EGO
• Warranty Policy | EGO POWER+

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>