LEDone LOC-T82FTU-15W T8 Cool White LED Light Bulb Installation Guide

LOC-T82FTU-15W Type A+B Installation Guide

SAFETY INSTRUCTIONS:

Read instructions carefully before attempting to install fixture.

• WARNING: You MUST check the ballast compatibility list before installing.
• WARNING: Risk of fire or electric shock. LED tube installation requires knowledge of luminaires electrical systems. If not qualified, do NOT attempt installation. All wiring should be performed by a qualified electrician.
• WARNING: Disconnect power before installing or servicing. This fixture must be wired in accordance with the National Electrical Code and applicable local codes and ordinances.
• WARNING: Make certain power is OFF before installing or maintaining fixture. No user serviceable parts inside.
• WARNING: Dimming requires additional external dimming module!!!
• WARNING: Disconnect the power to avoid shock when the equipment is wet.
• WARNING: Check the ballast compatibility list before installing this tube to the fixtures with electronic ballast. Do NOT install this kit to the fixture if the ballast is not on the list. If the ballast is not on the list, bypass the ballast or confirm with the supplier.
• WARNING: If the tube is installed as Type B (bypass), the fixture will no longer operate fluorescent lamps.
• WARNING: Install this kit only in luminaires that have the construction features and dimensions shown in the photographs and/or drawings and where the input rating of the retrofit kit does not exceed the input rating of the luminaire.
• WARNING: Do NOT make or alter any open holes in an enclosure of wiring or electrical components during kit installation.
• WARNING: To prevent wiring damage or abrasion, do NOT expose wiring to edges of sheet metal or other sharp objects.
• WARNING: This LED tube is accepted as a component of a luminaire where the suitability of the combination shall be determined by authorities having jurisdiction.

CLEANING & MAINTENANCE:

CAUTION: Be sure the fixture temperature is cool enough to touch. Do NOT clean or maintain while the fixture is energized.

1. Clean lens with non-abrasive cleaning solution.
2. Do NOT open fixture to clean the LED. Do NOT touch the LED.
   Note: These instructions do not cover all details or variation in equipment, nor do they provide for every possible situation during installation, operation or maintenance.

INSTALLATION TYPE A: You MUST check the ballast compatibility list before installing.

1. Disconnect power of luminaire.

2. Remove existing tube lamp(s).
   a. Remove diffuser (if provided)
   b. Remove existing fluorescent lamp(s)

3. Check Ballast Compatibility list

4. Select the desired color temperature by locating the switch on the back side of the tube.

5. Install the LED tube(s).
   a. Read the label on the LED tube to ensure the power end of LED is aligned with powered tube socket. Then insert the LED lamp.
   b. Replace troffer lens, if present.
   c. After modification is completed, attach the replacement marking and cautionary label to a visible place on the luminaire and keep it visible after installation.

6. Restore the power of the luminaire.

CCT Selectable:

1. Locate the switch on the back of the tube.
2. CCT options: 3,500K / 4,000K / 5,000K

INSTALLATION TYPE B:
Note: The tube can work with single end and double end power input.

1. Disconnect power of luminaire.

2. Remove existing tube lamp(s).
   a. Remove troffer (if present)
   b. Remove existing fluorescent lamp(s)
   c. Remove ballast cover (cover may be secured with screws or tabs)

3. Select the desired color temperature by locating the switch on the back side of the tube.

4. Install the LED tube(s).
   a. Read the label on the LED tube to ensure the power end of LED is aligned with powered tube socket. Then insert the LED lamp by sliding the pins into the sockets and rotating a quarter turn until the LED tube locks in place.
   b. Replace troffer lens, if present.
   c. After modification is completed, attach the replacement marking and cautionary label to a visible place on the luminaire and keep it visible after installation.

5. Restore the power of the luminaire.

CCT Selectable:

1. Locate the switch on the back of the tube.
2. CCT options: 3,500K / 4,000K / 5,000K

DIMMING DIAGRAM:

Warning: Dimming requires additional external dimming module!!!

INSTALLATION:
Warning: Dimming requires additional external dimming module!!!

1. Disconnect power of luminaire.

2. Remove existing tube lamp(s).
   a. Remove troffer (if present)
   b. Remove existing fluorescent lamp(s)
   c. Remove ballast cover (cover may be secured with screws or tabs)

3. Rewire and install the dimming module.
   a. Remove the ballast, fix the dimming module with screws to the position of the originally installed ballast.
   b. Rewire according to the above installation wiring diagram. Note: The dimming module should be connected well with the ground.
   c. Install the ballast cover, make sure that all of the wires and dimming module are in the cover.

4. Insert the LED tube according to the label on the LED tube to ensure that the lamp and dimming module can work together. All wiring should be performed by a qualified electrician.

5. Once the tube is locked in place, it is fully installed.

6. Replace the troffer lens if present.
   a. After modification is completed, attach the replacement marking and cautionary label to a visible place on the luminaire and keep it visible after installation.

7. Restore the power of the luminaire.

Phone: (844) LEDONE6
Fax: 1-510-217-9461
Web:www.ledonecorp.com

References

• Energy Saving with LED Lighting Fixtures & Bulbs | LED One Corporation

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>