Delta Children’s Skyla Crib Instruction Manual

Delta Children’s Skyla Crib

READ ALL INSTRUCTIONS BEFORE ASSEMBLY AND USE.

KEEP INSTRUCTIONS FOR FUTURE USE.
ADULT ASSEMBLY REQUIRED DUE TO THE PRESENCE OF SMALL PARTS DURING ASSEMBLY, KEEP OUT OF REACH OF CHILDREN UNTIL ASSEMBLY IS COMPLETE.

Customer Service:
Web Site: www.deltachildrensproducts.com

• Delta Children’s Products
• 114 West 26th Street
• New York, NY 10001
• Tele.212-645-9033

THIS PRODUCT IS NOT INTENDED FOR INSTITUTIONAL OR COMMERCIAL USE.
If you have any questions or missing parts, contact us. DO NOT return product parts to the store from where it was purchased before contacting Delta Children’s Products Customer Service. Make sure that all pre-assembled parts are tight. The appearance of your product may be different from that pictured in this booklet. To register your product for important safety alerts and updates to your product please visit http://deltaenterprise.com/register.asp

CAUTION: ANY MATTRESS USED IN THIS CRIB MUST BE AT LEAST 27 1/4 INCHES BY 51 5/8 INCHES WITH A THICKNESS NOT EXCEEDING 6 INCHES.

WARNING: CRIB INFANTS CAN SUFFOCATE ON SOFT BEDDING. NEVER ADD A PILLOW, COMFORTER, OR PADDING. FAILURE TO FOLLOW THESE WARNINGS AND THE ASSEMBLY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. TO REDUCE THE RISK OF SIDS, PEDIATRICIANS RECOMMEND HEALTHY INFANTS BE PLACED ON THEIR BACKS TO SLEEP UNLESS OTHERWISE ADVISED BY THEIR PHYSICIAN. ADULT ASSEMBLY IS REQUIRED DUE TO THE SMALL PARTS.

• READ ALL INSTRUCTIONS BEFORE ASSEMBLING CRIB. KEEP INSTRUCTIONS FOR FUTURE USE.
• STRANGULATION HAZARD: STRINGS CAN CAUSE STRANGULATION! DO NOT PLACE ITEMS WITH A STRING AROUND A CHILD’S NECK, SUCH AS HOOD STRINGS OR PACIFIER CORDS. DO NOT SUSPEND STRINGS OVER A CRIB OR ATTACH STRINGS TO TOYS.
• STRANGULATION HAZARD: TO HELP PREVENT STRANGULATION TIGHTEN ALL FASTENERS. A CHILD CAN TRAP PARTS OF THE BODY OR CLOTHING ON LOOSE FASTENERS.
• STRANGULATION HAZARD: DO NOT PLACE A CRIB NEAR THE WINDOW WHERE CORDS FROM BLINDS OR DRAPES MAY STRANGLE A CHILD.
• FALL HAZARD: WHEN THE CHILD IS ABLE TO PULL TO A STANDING POSITION, SET THE MATTRESS TO THE LOWEST POSITION AND REMOVE BUMPER PADS, LARGE TOYS, AND OTHER OBJECTS THAT COULD SERVE AS STEPS FOR CLIMBING OUT. THIS CRIB HAS AN ADJUSTABLE MATTRESS SUPPORT. FOR THE CONVENIENCE OF THE PARENT WHEN THE BABY IS VERY SMALL, THE MATTRESS SUPPORT MAY BE USED IN THE HIGHEST POSITION. IMPORTANT: WITH THE MATTRESS SUPPORT AND MATTRESS IN THE HIGHEST POSITION, BE ABSOLUTELY SURE THAT THE TOP OF THE FRONT CRIB SIDE IS AT LEAST 3 INCHES HIGHER THAN THE TOP SURFACE OF THE MATTRESS. IF IT IS NOT, LOWER THE MATTRESS SUPPORT AND THE MATTRESS TO THE NEXT HIGHEST POSITION.
• FALL HAZARD: WHEN THE CHILD IS ABLE TO CLIMB OUT OR REACHES THE HEIGHT OF 35 IN. (90 CM), THE CRIB SHALL NO LONGER BE USED, THE CHILD SHOULD BE PLACED IN A YOUTH OR REGULAR BED.
• CHECK THIS PRODUCT FOR DAMAGED HARDWARE, LOOSE JOINTS, MISSING PARTS, OR SHARP EDGES BEFORE AND AFTER ASSEMBLY AND FREQUENTLY DURING USE. DO NOT USE CRIB IF ANY PARTS ARE MISSING, DAMAGED, OR BROKEN. CONTACT DELTA CHILDREN’S PRODUCTS FOR REPLACEMENT PARTS AND INSTRUCTIONAL LITERATURE IF NEEDED. DO NOT SUBSTITUTE PARTS.
• DO NOT USE A WATER MATTRESS WITH THIS CRIB.
• IF REFINISHING, USE A NON-TOXIC FINISH SPECIFIED FOR CHILDREN’S PRODUCTS.
• NEVER USE PLASTIC SHIPPING BAGS OR OTHER PLASTIC FILM AS MATTRESS COVERS BECAUSE THEY CAN CAUSE SUFFOCATION.
• INFANTS CAN SUFFOCATE IN GAPS BETWEEN CRIB SIDES AND A MATTRESS THAT IS TOO SMALL.
• ENSURE A SAFE ENVIRONMENT FOR THE CHILD BY CHECKING REGULARLY, BEFORE PLACING THE CHILD IN THE CRIB, THAT EVERY COMPONENT IS PROPERLY AND SECURELY IN PLACE.

TODDLER BED

A WARNING ENTRAPMENT/STRANGULATION HAZARD

• INFANTS HAVE DIED IN TODDLER BEDS FROM ENTRAPMENT AND STRANGULATION. FAILURE TO FOLLOW THESE WARNINGS AND THE ASSEMBLY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH.
• NEVER USE A BED WITH CHILDREN UNDER 15 MONTHS.
• NEVER PLACE THE BED NEAR WINDOWS WHERE CORDS FROM BLINDS OR DRAPES MAY STRANGLE A CHILD.
• DO NOT PLACE ITEMS WITH A STRING, CORD, OR RIBBON AROUND A CHILD’S NECK, SUCH AS HOOD STRINGS OR PACIFIER CORDS.
• DO NOT SUSPEND STRINGS OVER A TODDLER BED FOR ANY REASON.
• THE USERS MAXIMUM WEIGHT SHALL NOT BE GREATER THAN 50 LB (22.7 kg).
• THE MATTRESS INTENDED FOR USE ON THE BED SHALL BE A FULL-SIZE CRIB MATTRESS HAVING MINIMUM DIMENSIONS OF 51 5/8 IN. (1310 MM) IN LENGTH, 27 1/4 IN. (690 MM) IN WIDTH AND 4 IN. (100 MM) IN THICKNESS.
• A STABILIZER BAR MUST BE USED WHEN CONVERTED TO A TODDLER BED.
• GUARDRAIL(S) PROVIDED MUST BE USED TO AVOID THE FORMATION OF A GAP BETWEEN THE MATTRESS AND THE BED THAT COULD CAUSE AN ENTRAPMENT.

NOTES ON ASSEMBLY:

• DURING THE ASSEMBLY PROCESS WHENEVER USING SCREWS OR BOLTS, CHECK EACH BY PLACING THE SCREW/BOLT ON THE DIAGRAM OF THE ITEM WHICH IS DRAWN ACTUAL SIZE AND DESIGN. BE SURE TO USE THE PROPER SIZE AND SHAPE SPECIFIED IN THE INSTRUCTIONS.
• TO ASSEMBLE THIS UNIT YOU MAY BE REQUIRED TO PLACE THE UNIT ON IT’S SIDE AND FACE. IT IS STRONGLY RECOMMENDED THAT ASSEMBLY IS DONE ON A SOFT, NON-ABRASIVE SURFACE TO AVOID DAMAGING THE FINISH.

NOTES ON USE:
KEEP CHILDREN AND OTHERS SAFE BY FOLLOWING THESE SIMPLE RULES:

• DO NOT ALLOW ANY CHILD TO PLAY ON FURNITURE
• DO NOT ALLOW CLIMBING ON ANY PIECE OF FURNITURE.
• DO NOT ALLOW HANGING FROM ANY PIECE OF FURNITURE.
• ALWAYS MONITOR YOUR CHILD’S ACTIVITY WHEN IN THE NURSERY.

NOTES ON CARE AND MAINTENANCE:

• DO NOT SCRATCH OR CHIP THE FINISH.
• INSPECT THE PRODUCT PERIODICALLY, CONTACT DELTA CHILDREN’S PRODUCTS FOR REPLACEMENT PARTS OR QUESTIONS.
• DO NOT STORE THE PRODUCT OR ANY PARTS IN EXTREME TEMPERATURES AND CONDITIONS SUCH AS A HOT ATTIC OR A DAMP, COLD BASEMENT. THESE EXTREMES CAN CAUSE A LOSS OF STRUCTURAL INTEGRITY.
• AN OCCASIONAL WAXING, PLUS REGULAR CLEANING WITH MILD SOAP ON A SOFT CLOTH, FOLLOWED BY A CLEAN DAMP CLOTH, THEN A DRY CLOTH, WILL PRESERVE THE ORIGINAL LUSTER AND BEAUTY OF THIS FINE FINISH.
• DO NOT USE ABRASIVE CHEMICALS.
• DO NOT SPRAY CLEANERS DIRECTLY ONTO FURNITURE, SPRAY ONTO CLEANING CLOTH AND THEN APPLY TO FURNITURE. TEST IN AN INCONSPICUOUS AREA BEFORE APPLYING TO ENTIRE UNIT.
• LIFT SLIGHTLY WHEN MOVING ON CARPETING TO PREVENT LEG BREAKAGE.
• USE OF A VAPORIZER NEAR FURNITURE WILL CAUSE WOOD TO SWELL AND FINISH TO PEEL.

PARTS

• MAKE SURE THAT ALL PRE-ASSEMBLED PARTS ARE TIGHT.

M. MATTRESS SUPPORT x 1
POUCH ATTACHED TO THE MATTRESS SUPPORT KEEP INSTRUCTIONS AND ANY EXTRA HARDWARE AND TOOLS IN THIS POUCH AFTE  ASSEMBLYWARNINGS RELATED TO THE SAFE USE OF THIS CRIB ARE PRINTED ON THE POUCH

INSTALLATION INSTRUCTION

CRIB ASSEMBLY

STEP 1

ATTACH (1) CRIB END (PART E) TO (1) LEFT REAR LEG (PART C) AND (1) LEFT FRONT LEG (PART F) WITH (5) M6×65mm BOLTS (PART N) USING THE M4 ALLEN WRENCH AS SHOWN. REPEAT ON THE OTHER CRIB END.

NOTE: AFTER ASSEMBLY, THE “STEPPED HOLES” IN BOTH POSTS ARE ON THE SAME SIDE.

STEP 2

ATTACH (1) BACK SIDE (PART B) TO THE ASSEMBLIES FROM STEP 1 USING (4) M6×38mm BOLTS (PART P) AND (2) M4×30mm METAL PIN (PART L). INSERT THE SLOT OF THE TOP RAIL (PART A) INTO THE TENON ON TOP OF THE BACK SIDE (PART B), THEN INSERT THE M6×38mm BOLTS (PART P), THROUGH THE LEGS INTO THE THREADED INSETS ONTO THE TOP RAIL (PART A) AS SHOWN. TIGHTEN WITH THE M4 ALLEN WRENCH.

NOTE: THE TENON IN PART B MUST FACE UP.

STEP 3

ATTACH THE MATTRESS SUPPORT (PART M) IN ALL CORNERS USING (1) M6×15mm BOLT (PART S) IN EACH CORNER. TIGHTEN WITH THE M4 ALLEN WRENCH.THE A WARNINGS PRINTED ON THE POUCH ATTACHED TO THE MATTRESS SUPPORT MUST FACE UP, THE SPRINGS MUST FACE UP. THIS CRIB HAS (3) ADJUSTMENT POSITIONS, USE THEHIGHEST ONLY FOR NEW BORNS, MOVE THE MATTRESS DOWN AS THE CHILD GROWS.

WARNING:
FALL HAZARD: WHEN THE CHILD IS ABLE TO PULL TO A STANDING POSITION, SET THE MATTRESS TO THE LOWEST POSITION AND REMOVE BUMPER PADS, LARGE TOYS, AND OTHER OBJECTS THAT COULD SERVE AS STEPS FOR CLIMBING OUT.

STEP 4

INSERT (2) M4×30mm METAL PIN (PART L) INTO THE TOP HOLE ON EACH SIDE OF THE FRONT SIDE (PART H), THEN ATTACH THE FRONT SIDE (PART H) TO THE ASSEMBLIES FROM STEP 4  USING (4) M6×38mm BOLT.INSERT THE SLOT OF THE TOP RAIL (PART A) INTO THE TENON ON TOP OF THE FRONT SIDE (PART H), THEN INSERT THE M6×38mm BOLTS (PART P), THROUGH THE LEGS INTO THE THREADED INSETS ONTO THE TOP RAIL (PART A) AS SHOWN. TIGHTEN WITH THE M4 ALLEN WRENCH.

STEP 5

STORE THE ASSEMBLY INSTRUCTION BOOKLET AND THE ALLEN WRENCH IN THE POUCH ATTACHED TO THE MATTRESS SUPPORT.

WARNING: SEE PAGE 2 FOR INFORMATION

TODDLER BED CONVERSION

STEP 1

• REMOVE THE TOP RAIL AND FRONT SIDE INSTALLED IN STEP 5 & 6 OF SECTION 1 CRIB ASSEMBLY.

STEP 2

ATTACH THE STABILIZER BAR (PART J) TO THE ASSEMBLIES FROM STEP 1 USING (2) M4×30mm METAL PINS (PART L) AND (2) M6×38 mm BOLTS (PART P). TIGHTEN WITH THE ALLEN WRENCH.

STEP 3

ATTACH THE SAFETY RAIL (PART K) TO THE ASSEMBLIES FROM STEP 2 USING (3) M6×38 mm BOLTS (PART P) .TIGHTEN WITH THE ALLEN WRENCH.

• A STABILIZER BAR MUST BE USED WHEN CONVERTED TO A TODDLER BED.

WARNING: SEE PAGE 3 FOR TODDLER BED WARNINGS

THE MATTRESS SUPPORT MUST BE IN THE LOWEST POSITION. STORE ALL HARDWARE SAFELY. READ ALL WARNINGS ON PAGE 3

FULL SIZE BED CONVERSION

STEP 1

YOU HAVE THE OPTION TO CONVERT THE CRIB TO A FULL SIZE BED. SIMPLY FOLLOW STEPS IN REVERSE ORDER TO DISASSEMBLE THE CRIB. THEN REMOVE THE REAR LEGS FROM THE LEFT CRIB END AND RIGHT CRIB END WITH THE M4 ALLEN WRENCH AS SHOWN. STORE ALL PARTS AND HARDWARE IN A SAFE PLACE.

STEP 2

• TO USE AS A FULL-SIZE BED HEADBOARD ONLY. ATTACH ADAPTER PLATES (PART T) TO BOTTOM OF REAR SIDE RAIL LEGS USING (4) M6x15mm BOLTS (PART S). HAND-TIGHTEN BOLTS IN PLACE. ADJUST UP OR DOWN TO ALLOW FOR CONNECTION TO THE BED RAIL. ADAPTER “TABS” WILL KEEP ADAPTER PLATE FROM ROTATING

STAND HEADBOARD UP. ATTACH TO BED FRAME WITH BOLTS AND NUTS (SUPPLIED BY BED FRAME MANUFACTURER). ADAPTER PLATES (PART T) CAN BE ADJUSTED UP OR DOWN TO BEST SUIT BED FRAME.TIGHTEN ALL BOLTS ONCE BED RAIL IS ADJUSTED.

NOTE: BED FRAMES ARE NOT SUPPLIED WITH THIS SYSTEM, BUT CAN BE PURCHASED AT MATTRESS STORES.

STEP 3
A BED RAIL SYSTEM IS AVAILABLE TO FIT YOUR CRIB TO CONVERT TO A COMPLETE FULL-SIZE BED. SEE THE RETAIL STORE OR CONTACT DELTA CHILDREN PRODUCTS FOR MORE INFORMATION

Customer Service:
Web Site: www.deltachildrensproducts.com

• Delta Children’s Products
• 114 West 26th Street
• New York, NY 10001
• Tele.212-645-9033

Warranty: This Delta Crib is warranted to be free from defects for a period of 1 year from the date of purchase under normal use. This warranty extends only to the original retail purchaser and is valid only when supplied with proof of purchase, or if received as a gift, when the registration is on file with Delta.

To register your product for important safety alerts and updates to your product please visit http://deltaenterprise.com/register.asp Please do not return this item to the store before contacting us about missing parts or with any questions. To report a problem, please log on to www.deltachildrensproducts.com and click the Customer Service Tab, log on to www.deltaenterprise.com/customer_service.asp, or contact us by phone at 212-645-9033. In the event that you need to contact our customer service department please have the Style Number and Lot Number available. Use the space below to make a note of those numbers. They can befound on the label on the Crib End bottom rail.

• Style No.:
• Lot No. :
• Pack Date:
• Date of Purchase: (you should also keep your receipt)

Download PDF:Delta Children’s Skyla Crib Instruction Manual

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>