CENTEK CT-2314 Steam Iron Instruction Manual

: June 11, 2024
: CENTEK

Table of Contents

CT-2314 Steam Iron
SAFETY PRECAUTIONS
APPLIANCE DESCRIPTION
COMPLETENESS
WORKING PROCEDURE
CARE OF THE DEVICE
SPECIFICATIONS
DISPOSAL
CERTIFICATION DATA, GUARANTEE
INFORMATION ABOUT THE MANUFACTURER, IMPORTER
Warranty Certificate
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

CT-2314 Steam Iron
Instruction Manual STEAM IRON

CT-2314 Steam Iron

DEAR CUSTOMER!
Prior to operating the appliance, please carefully read the present manual which contains important information regarding its proper and safe operation. Take care not to lose the present manual. The manufacturer will not be responsible for any damage resulting from improper use of the appliance or from non-observance of the instructions and provisions of the present manual, as well as from attempts by unskilled persons at repairing the appliance. Should You decide to transfer the appliance to another person, please pass the present manual over along with it.
The steam iron is a home appliance and is not designed for industrial purposes!
PURPOSE OF THE APPLIANCE: for ironing out wrinkles on fabric clothes.

SAFETY PRECAUTIONS

The appliance purchased by You complies with all official safety standards applicable to electric appliances in the Russian Federation. The following requirements should be strictly observed in order to avoid situations hazardous for human life and health, as well as premature failures of the appliance:

Connect the appliance only to a properly installed electric socket. Ensure that the power supply grid voltage corresponds to the one indicated on the appliance.
The appliance should not be used by physically, sensory or mentally handicapped persons (including children) or by persons without sufficient experience or knowledge, unless such persons are under supervision, or have been instructed on the use of the appliance, by the persons responsible for their safety. Take precautions not to let children play with the appliance.
Do not leave the appliance connected to power supply unattended.
Disconnect the iron from the electric power grid before filling the water tank.
If the power cable should be damaged, have it replaced by the Manufacturer, authorized service centre or similar skilled personnel to avoid dangerous situations.
Do not use the appliance if the power cable or plug is damaged.
Do not submerge the appliance in water.
Do not allow the power cable to contact the hot sole of the appliance.
Prior to putting the appliance away for storage let it cool down completely.
Use and store the appliance on a stable surface.
CAREFUL: accessible surfaces of the appliance can reach high temperature during operation. Do not touch the hot surfaces.
Do not connect the appliance to power supply via a timer or other remote control device.
The surface of the heating element will remain hot for some time after the appliance is turned off.
Do not operate the appliance if it has been dropped, has visible damage or leaks water.
Special instructions for transportation (shipment) and sale: none.

ATTENTION! Before first use, try the iron out on a useless piece of fabric to ensure that the sole or the water tank is not contaminated. Some parts of the appliance are slightly lubricated during assembly; therefore some smoke can occur when the iron is turned on for the first time. This should disappear within a few seconds.

APPLIANCE DESCRIPTION

Sprayer
Filler neck
Steam switch
Spray button
Steam shock button
Mode controller
Ceramic-coated sole
Indicator
Self-cleaning button

COMPLETENESS

– Iron – 1 pc.
– Measuring cup – 1 pc.
– User manual – 1 pc.

WORKING PROCEDURE

Remove the protective film/cardboard from the sole of the iron. The steam iron can use ordinary tap water. If the hardness of tap water exceeds 17° dH, it is necessary to use distilled or demineralized (filtered) water to increase the service life of the iron. Fill the water tank (for steam ironing). Disconnect the iron from the mains and set the steam supply switch to the «0» position.
Fill in the water so that its level is visible approximately in the middle of the transparent part of the iron body. Plug the iron into an electrical outlet.
TEMPERATURE CONTROL
Sort the laundry according to the composition of the fabrics and the appropriate ironing temperature. Iron products that require a lower temperature first, since the iron heats up faster than it cools down. The indicator lamp signals the heating of the iron. Turning off the lamp indicates that the iron has reached the set temperature and You can start ironing.
FUNCTIONS
SPRAYER
To spray water on the fabric, press the «Spray» button.
DRY IRONING/STEAM
The steam supply intensity can be changed using the steam supply regulator.
In the position, the steam supply is turned off (dry ironing).
STEAM STROKE
To use the steam shock function (powerful one-time steam emission), press the «Steam Shock» button.
ATTENTION! Use the «Steam blow» button only after the iron is heated to the steam production temperature. Do not press the steam shock button more than three times in a row.
Auto-off: the iron will automatically turn off and the appliance will go into standby mode after 30 seconds in a horizontal position or overturning and 8 minutes in a vertical position. When you turn off the iron, the auto-off indicator will flash.
In order for the iron to heat up again, simply lift or move the appliance slightly. The auto power off indicator will stop flashing. Instead, the heating indicator will light up. The iron is ready for use again.

CARE OF THE DEVICE

Set the temperature controller to the OFF position and disconnect the iron from the mains. Place the iron in an upright position and let it cool completely. Drain the water from the iron container. Set the steam supply regulator to the position. Remove deposits from the sole of the iron with a solution of acetic acid. Wipe the iron body with a damp cloth, then wipe dry.
THERMAL PROTECTION
In case of failure of the iron thermostat, the device will automatically turn off to avoid overheating. In this case, you should contact customer service.
SELF-CLEANING FUNCTION
The self-cleaning function is designed for removing scale from the iron’s sole. We recommend using the self-cleaning function at least every two weeks.
– Fill the iron with water and connect it to power supply.
– Set the steam regulator to the position and the temperature regulator to the “LINEN” position. Wait for the iron to heat up and disconnect it from power supply. Holding the iron horizontally press and hold the “self-cleaning” button. Gently shake the iron. Steam and boiling water will be discharged form the sole, washing out impurities. Release the “self-cleaning” button as soon as the water in the tank is used up. Repeat the cleaning procedure if necessary.
– After the self-cleaning is over, connect the iron to power supply and let it heat up so as to dry out the sole. Disconnect the iron when it reaches the preset temperature. Carefully slide the iron over a useless piece of fabric to remove the stains that may have formed on the sole during self-cleaning.
Let the iron cool down before putting it away for storage.
ATTENTION! When ironing, water may flow through the sole of the iron. This happens if the «MIN/SYNTHETIC» temperature is too low. If this happens, turn the temperature control to the «SILK/COTTON/LINEN» position. Once the newly selected temperature is reached, the water flow will decrease significantly.

We draw your attention to the fact that a slight flow of water through the sole of the iron is permissible and is not a defect.

SPECIFICATIONS

– Nominal rated voltage: 220-240 V ~50/60 Hz
– Nominal power rating: 2400–2800 W

DISPOSAL

Upon expiry of its service life the appliance can be disposed of separately from ordinary domestic waste. You can turn it over to a specialized electric and electronic appliance disposal and recycling centre.

CERTIFICATION DATA, GUARANTEE

The service life of this item is 5 years since the date of sale to the end user, provided the item will be used in strict accordance with the present manual and the applicable technical standards. Upon expiry of the service life please contact the nearest authorized service centre for suggestions as to further operation of the appliance. The manufacturing date of the appliance is integrated into the serial number (digits 2 and 3 – year, digits 4 and 5 – month of manufacture). If any questions related to appliance maintenance should arise, or if the appliance has malfunctions, apply to the CENTEK TM Authorized Service Center. The address of the service center can be found on the website https://centek.ru/servis.
Service support contacts: Phone: +7 (988) 24-00-178,
VK: vk.com/centek_krd. General Service Center: OOO «Larina-Servis», Krasnodar,
Phone: +7 (861) 991-05-42.
The product has the Certificate of Conformity No.:
ЕАЭС RU С-CN.ВЕ02.В.02693/20 of 01.09.2020.

INFORMATION ABOUT THE MANUFACTURER, IMPORTER

I mporte to EAEU by: Individual niy Predprinimatel Asrumyan Karo
Shurikovich. Addr ess: Russia, 350912 Krasnodar, ul . Atamana Lysenko, 23, pgt. Pashkovskiy, phone: +7 (861) 2-600-900.
DEAR CONSUMER!
The guarantee period for all appl iances amounts to 12 months from the date of sal e to the end consumer. With this Warranty Card the Manufacturer confirms the proper condition of the appl iance and undertakes to repair, free of charge, all defects caused by the Manufacturer’s default.
GUARANTEE MAINTENANCE TERMS

The guarantee shall be valid if the following documentation conditions are observed:
• The original Warranty Card shall be filled out correctly and clearly, indicating the of appliance model, serial number and sale date, the stamp of the seller company and signature of its representative shall be available, as well as the stamps on each coupon and the buyer’s signature in the Warranty Card.
The Manufacturer reserves the right to reject guarantee maintenance if the buyer fails to provide the abovementioned documents or if the information contained therein is incomplete, illegible or ambiguous.
The guarantee shall be valid if the following operation conditions are observed:
• the appliance is used in strict accordance with the present manual;
• the safety rules and requirements are observed.
The guarantee does not apply to regular maintenance, cleaning, installation and setup of the appliance at the owner’s location.
The guarantee does not apply in the following cases:
• mechanical damage;
• normal wear of the appliance;
• non-observance of operation requirements or erroneous actions on the part of the user;
• improper installation or transportation;
• natural disasters (lightning, fire, flood, etc.), as well as any other causes beyond the Manufacturer’s or Seller’s control;
• ingress of foreign objects, liquids or insects into the inside of the appliance;
• repairs or modifications to the appliance by unauthorized persons;
• use of the appliance for commercial purposes (loads exceeding normal domestic application), connection of the appliance to utility and telecommunication networks incompliant with national technical standards;
• failure of the following accessories, if replacement of these is allowed by design and does not involve disassembly of the appliance:
a) remote control units, rechargeable batteries, replaceable batteries (power cells), external power supply units and chargers;
b) consumables and accessories (packaging, covers, slings, carry bags, mesh screens, blades, flasks, plates, supports, grilles, spits, hoses, tubes, brushes, nozzles, dust collectors, filters, smell absorbers);
• for battery-powered appliances – operation with inappropriate or depleted batteries;
• for rechargeable battery-powered appliances – any damage caused by improper battery charging and recharging.
The present guarantee is provided by the Manufacturer in addition to the consumer rights determined by the applicable legislation and does not limit these rights in any way.
The Manufacturer shall not be made liable for possible damage, directly or indirectly inflicted by CENTEK brand products on people, domestic animals, the consumer’s or third persons’ property if such damage is inflicted as the result of non-observance of appliance installation and operation requirements, deliberate or negligent actions (omission) by the consumer or third persons, as well as of force majeure circumstances.
Service centers will only accept appliances in a clean state (there should be no food residues, dust and other contamination on the appliance).

The Manufacturer reserves the right to change the design and specifications of the appliance without prior notice.

Warranty Certificate

Attention! Please ask the seller to fill out the warranty card and tear- off coupons in full.
The ticket is valid in the presence of all stamps and marks.
Product……………….
Model………………
Serial number ………………
Date of sale………………..
These tear-off coupons are filled in by a representative of the seller
Product……………
Model………………..
Serial number …………………
DATE OF SALE ……………….
Vendor,……………..
Seller’s address………………
Full name and phone number of the buyer service center
RELEASE DATE ……………
These tear-off coupons are filled in by a representative of the
TYPE OF REPAIR………………………
DATE OF RECEIPT………..