MORRIS MHR-20042 Convection Heater User Manual

: June 11, 2024
: MORRIS

Table of Contents

MORRIS MHR-20042 Convection Heater
Safety Warnings
Assembly
Controls/parts
Storage
NOTICE ABOUT RECYCLING
DECLARATION OF CONFORMITY
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

MORRIS MHR-20042 Convection Heater

Safety Warnings

PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY
BEFORE USING THE APPLIANCE.

This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
Children of less than 3 years should be kept away unless continuously supervised. Children aged from 3 years and less than 8 years shall only switch on/off the appliance provided that it has been placed or
installed in its intended normal operating position and they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children aged from 3 years and less than 8 years shall not plug in, regulate and clean the appliance or perform user maintenance.
CAUTION – Some parts of this product can become very hot and cause burns. Particular attention has to be given where children and vulnerable people are present.
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
WARNING: In order to avoid overheating, do not cover the heater.
The heater must not be located immediately below a socket-outlet.
Do not use this heater in the immediate surroundings of a bath, a shower or a swimming pool.
Do not use the appliance for other than its intended use. For domestic indoor use only.
Place the appliance on a flat, stable, heat-resistant surface. Operating the product in any other position could cause a hazard.
Do not use this heater if it has been dropped.
Do not attempt to repair, disassemble or modify the appliance. There are no user-serviceable parts inside.
CAUTION – if using an extension lead please ensure you do not exceed the maximum rated running wattage/load of the extension lead.
Disconnect from mains when not in use or when moving or cleaning.
The heater is hot when in use. To avoid burns, do not let bare skin touch hot surface.
Do not insert or allow foreign objects to enter the ventilation or exhaust openings as this may cause an electric shock, fire or damage to the appliance.
Do not cover the heater. A fire may occur if the heater is covered with or touches flammable material, including curtains, drapes, bedding etc. when in operation. KEEP THE HEATER AWAY FROM SUCH MATERIALS and any other flammable material with a minimum distance of 1m.from the air outlet.
WARNING FOR BATTERIES OF THE REMOTE CONTROL KEEP OUT OF REACH OF CHILDREN. Swallowing can lead to chemical burns, perforation of soft tissue and death. Severe burns can occur within 2 hours of ingestion. Seek medical attention immediately.
Keep batteries out of the reach of children.
Do not allow children to replace batteries without adult supervision.
Do not short-circuit batteries.
Do not heat batteries.
Remove batteries from equipment if it is not to be used for an extended period of time unless it is for emergency purposes.
Always select the correct size and type of battery most suitable for the intended use.
Information provided with the equipment to assist correct battery selection should be retained for reference.
Clean the battery contacts and also those of the equipment prior to battery installation.
Ensure that the batteries are installed correctly with regard to polarity (+ and –).
Remove exhausted batteries promptly.
Do not dismantle batteries.
Do not dispose of batteries in fire except under conditions of approved and controlled incineration.
Batteries may be disposed of via communal refuse arrangements provided no local rules to the contrary exist.
WARNING: Do not use this heater in small rooms when they are occupied by persons not capable of leaving the room on their own, unless constant supervision is provided.
Do not use if there are visible signs of damage to the heater.
Use this heater on a horizontal and stable surface, or fix it to the wall, if this is allowed – as applicable.

Note: When the product start heating, stop heating or change power, there might be ‘click’ sound because of the expansion and contraction of iron sheet. This is normal; the sound will disappear after a few minutes.

PICTURES IN THE MANUAL ARE FOR REFERENCE ONLY
AND IS SUBJECT TO THE PHYSICAL PRODUCT IN THE PACKING BOX

Assembly

Turn the body of the heater upside down on a scratch resistant and stable surface.
Place the foot bases over the holes on each side of the heater.
Fix the foot bases in place by screwing in four screws on each side.

Remote control
The remote control requires one 2025 – 3V cell.
Follow the +/- polarity indicated on the remote control.
The remote control must be pointed towards the remote sensor on the control panel. If the remote control doesn’t operate as expected, replace the cell.

Controls/parts

A. Heater body
B. Front handle
C. Control panel
D. Wheel base
E. Rear handle
F. On/off power switch
G. Cable storage
H. Remote control storage slo
a. Thermostat button
b.＋: Temperature & hours increase button
c. Power / Mode selection button
d. Timer button
e.－: Temperature & hours decrease button
f. Stand-by button

Move the appliance using the integrated handle.
The remote control can be stored in the integrated slot into the appliance when it is not used.

On
Press the on/off power switch [F] to turn the appliance on. The stand-by button [f] and Timer button [d] will light on. The product is now in stand-by awaiting a mode to be selected via the buttons on the appliance or the remote control. Press button or the screen and other buttons will light on also. The appliance emits a beep sound.
The following settings can be performed using the touch panel or the remote control.
A beep sound is emitted at every key press. If you want to turn off the buttons’ beep sound, press both “+” [b] and “-” [e] buttons for 3 seconds. If you want to recover the beep sound, press both buttons for 3 seconds again. Press the stand-by button [f] to exit the stand-by mode and begin selection of the different modes. Heater will start working under High power .

Heating power and Eco mode setting
Press the Power/Mode button(c), it will cycle from High power Medium power Low power Eco mode( ECO) .
Under Low power, Medium power and High power setting, the heater will keep working controlled by thermal cut-out.
Note: The higher the power is, the quicker the desired temperature will be achieved but the power consumption will be higher. It is recommended to operate the appliance at the lowest power levels when using it for a long time.

Eco mode
Press the Power/Mode button (c), until the “ECO” light turn on.
Under Eco mode, the heating power will adjust automatically when the room temperature is approaching the setting temperature.
Example: The setting temperature is 25℃. When the room temperature is less than 22℃, the heater will work under High power . When the room temperature rises to 23℃, the heater will change to work under Medium power . When the room temperature rises to 24℃, the heater will change to work under Low power . When the room temperature reaches to the setting temperature 25℃, the heater will switch off automatically. And when the room temperature is lower than setting temperature, the heater will switch on again under Eco mode.

Remark: if no thermostat setting, the default temperature is 23℃.

Thermostat setting
Anti-frosting setting: 5°C
Desired temperature setting range:10°C–30°C

Press the Power/Mode button (c) to set the power mode.
Press the thermostat button (a), the temperature digit will blink.
Use the “+” [b] and “-” [e] buttons to set the desired temperature.
The setting temperature digit will stop blinking and the setting temperature will appear on screen. The heater will maintain the air temperature in the room by switching on and off automatically.
Remark 1: No matter under any power mode to set the temperature, after thermostat setting, the heater will work under ECO mode only.
Remark 2: The temperature displayed on the screen is the temperature you have set.

Timer: Auto power on
Note: This function should only be set if you require the heater to be automatically turned on after a certain period of time (1 to 24 hours from the time the function is set). Only make timer power on setting under Stand-by mode.

Press the on/off power switch [F] to turn the appliance on. The button stand-by button [f] and Timer button [d] will light on. The appliance will be in Stand-by mode.
Press the Timer button(d), the light on and will turn on, and the start hour digit (0.0) will blink.
Use the “+” [b] and “-” [e] buttons to set the heater operation time between 1 and 24 hours. 0.0-5.0 hoursincrease by 0.5 hour, 5.0-24 hours increase by 1 hour. This function will activate once the hour digit stopsblinking. The count down digits will show on the display and the timer symbol ( ) will keep blinking till time runs out.
The heater will automatically turn on when the time runs out.

Note 1: After the timer power on setting, you can make the power mode and temperature setting. So that the heater will turn on at the desired temperature and power mode setting.
Note 2: When using timer modes, consideration should be given to the fact that the heater may turn on whilst unattended. Always follow the safety instructions provided.

Timer: Auto power off
Note: This function should only be set if you require the heater to be automatically shut off after a certain period of time (1 to 24 hours from the time the function is set).

While heater working, press the Timer button(d), the light on and will turn on, and the start hour digit (0.0) will blink.
Use the “+” [b] and “-” [e] buttons to set the heater operation time between 1 and 24 hours. 0.0-5.0 hours
increase by 0.5 hour, 5.0-24 hours increase by 1 hour. This function will activate once the hour digit stops blinking. The count down digits will show on the display.
The heater will automatically shut off when the time runs out.
Cancel Timer: turn off the heater from On/off [F] button at the back of the device

Child lock setting
Press both [c] and [f] Power & Stand by buttons for 3 seconds, the buttons will be locked but no symbol will show on display.
If you need to unlock, press both same buttons for 3 seconds again.

Off
Press the on/off switch [F] to turn the appliance off completely.
To disconnect the appliance, remove the plug from the socket.

Tip-over protection
This heater is protected with a safety switch that turns off the appliance automatically when the heater falls over, or is at an excessive angle from the horizontal. This helps prevent accidents, and the heater will resume operation when it is put back upright.

Overheat protection
This heater is protected with overheat protection that switches off the appliance automatically in case of severe overheating. In this case, unplug the appliance, wait about 30 minutes for it to cool and remove any possible cause of overheating, eg. something covering the heater. Check for damage to the appliance, the cord and the plug. If there is no damage, plug the unit back in and switch it on as described above. If the heater still does not turn on, please contact Customer Service for assistance.

Maintenance and cleaning
The appliance should be regularly cleaned when in use in accordance with the following instructions:

Unplug and let the appliance cool before cleaning.
Gently clean the outside surface and the control panel of the appliance with a damp lint-free soft cloth.
If dust is present within the slits of the device, it is recommended to blow them through the use of a vacuum cleaner, a blower .
Do not use harsh detergents, chemical cleaners or solvents as they may damage the appliance feet.

Storage

Keep the original packaging to disassemble the appliance and store it.
Keep the appliance in a dry and clean place.
Store the unit out of reach of children.

Information requirement for the electric local space heaters

Model identifier(s): MHR-20042

No

| | | | with distance control option| No
| | | | with adaptive start control| No
| | | | with working time limitation| Yes
| | | | with black bulb sensor| No

Contact details

| Kalliopi Karyda & Co LP
87A,17is Noemvriou str, P.C.55535 Pylea, Thessaloniki, Greece T:+302316006600 F:+302316006650

NOTICE ABOUT RECYCLING

Your product is designed and manufactured with high quality materials and components which can be recycled and reused.
This symbol means that electrical and electronic equipment, at their end-of- life, should be disposed of separately from your household waste. Please dispose of this equipment at your local community waste collection/ recycling centre.
In the European Union there are separate collection systems for used electrical and electronic products.
Please help us to conserve the environment we live in!

DECLARATION OF CONFORMITY

Herewith, Kalliopi Karyda & Co LP states that this product, complies with the requirements of below directives:
EMC-Directive: 14 / 30 / EU
Low Voltage Directive: 14 / 35 / EU
ErP Directive: 09 / 125 / EC
CE Marking: 93 / 68 / EEC
RoHS Directive: 11 / 65 / EU & 15 / 863 / EU
The detailed declaration of conformity can be found at www.morris.gr
Exclusive importer in Greece:
Kalliopi Karyda & Co LP
87A, 17is Noemvriou str, P.C. 55535
Thessaloniki – Greece
T: +302316006600 | F: +302316006650
www.morris.gr