MORRIS HAD1101 Jet Hand Dryer User Manual
- June 11, 2024
- MORRIS
Table of Contents
MORRIS HAD1101 Jet Hand Dryer
WARNING
If you don’t use this unit properly or follow the safety guidelines
carefully, it would lead to serious personal injury.
Prohibited
Dot not open the front panel.
Otherwise, This may get an electric shock.
Do not use in a wet environment,
for example, near the bathroom where it may get the direct water and the
places where the condensation may form.
Do not use in Otherwise, this may cause electric shock and unit malfunction.
the bathtub or shower room
Do not allow the unit get wet. Otherwise, it will cause electric shock. Do not
allow the unit get wet.
Do not modify and disassemble the unit unnecessarily. Otherwise, this may
cause a fire, electric shock, or personal injury. Prohibit disassembling.
-
Use separate line
Using any other electric appliance with the same line, may cause the branch socket to become very hot and cause fire. -
Turn off the power switch before inspecting and cleaning the unit. Otherwise, may cause electric shock .
-
Turn off the power switch before inspecting and cleaning the unit. Otherwise, may cause electric shock.
-
Ensure the unit is properly grounded. Otherwise, may cause electric shock during malfunction or short circuit.
Earth grounding -
Installation work should be done by the qualified technician. connection Incorrect wiring connection can cause electric shock and fire.
-
Be sure to install a residual current circuit breaker. Otherwise, this may cause electric shock.
-
Use a type whose contact points are at least 3mm apart.
* Please use the products of CCC standard -
Recommended residual current circuit breaker (for ground-fault protection). (Use a single-phase 2-line, AC 220~240V/50/60Hz cable with a 20A rated current, 15mA-type rated operating current)
WARNING
If you don’t use this unit properly or follow the safety guidelines carefully,
it would lead to serious personal injury or property damage.
Do not let children hang from the unit. Otherwise, this may cause the unit to drop.
-
Always use the unit with the drain tank and air filter attached. Once water enters the unit inside, short circuit or electric shock occurs.
-
Wear gloves when inspecting and cleaning the unit follow m rue ions
Features -
If the unit does not start, or works abnormally, turn off the power switch and ground
-
fault breaker and contact your dealer for inspection and repair Otherwise, this may cause electric shock or fire due to short circuit.
-
Do not use in the following places:
-
Where the unit may come into direct contact with water.
-
Where the unit is under direct or strong sunlight. (this may cause sensor to malfunction)
-
Where the condensation may form within the unit.
Safety precautions before installing the unit
-
Do not attempt to install the unit with the power on (power cord). Otherwise, this may cause electric shock.
-
The installation location should be strong enough to support the unit, and the unit should be installed firmly on the surface.
Otherwise, this may cause personal injury due to the unit falling. -
Wear gloves when installing the unit. Otherwise, this may cause injury.
Features
- “No touch” hand drying ensures complete hygiene.
- High-speed drying your wet hands, economical of money for paying electric charge alone.
- A tamper-proof timer built is to prevent overuse.
- No need paper towels, ease of maintenance
- No pollution, with antibacterial coating.
- To prevent overusing the unit, the built-in timer will stop the unit after 30 seconds. To continuous use, draw back you hands and put them in again.
Technical Parameters
r
Rated Voltage
| ****
AC220-240V
| ****
Waterproof Grade
| “
IPX4
---|---|---|---
Rated Frequency| 50/60HZ| Heating conditions| ****
Ambient temperature<25″C
Rated Power| 1650W| Air speed| 95m/s
Motor Power| 800W| Drying Time| 10seconds
weight
“-
| ****
12KG
| Overall size(mm)| 300 X 222 X 730
Name of the various components
Installation methods
Installation methods
Routine Cleaning
Cleaning the Unit body Before it gets obviously dirty.
- Clean the unit with a soft cloth. If the unit gets very dirty, clean with a soft cloth dampened with neutral agent, then clean with a dry soft cloth.
- Remove the dirt from the sensor. (to prevent malfunction)
Note
- Only use the neutral cleaning agents.
- Do not use thinner, acidic or alkaline toilet cleaners, or nylon brush. (Otherwise, they may damage the smoothness of surface) Only use the alcohol to clean the hand-drying area. (Do not use alcohol anywhere else)
- Alcohol here means the alcohol used for disinfection (concentration below 83%).
- If the chemical cloths used, please read their instructions first.
- Disinfecting agents will damage your unit.
Draining and Cleaning the drain tank Before it fills up (at least once a week)
- The water blown off the hands is called “drain water” .
- Empty the drain water at any moment, in order to prevent
- It will start smelling if the accumulated water remains in the tank for too long time.
Pull the drain tank out in the horizontal direction. This ensures the drain water does not splatter out.
- Open the cover and empty the water. Cover
- Pull the cover up with your fingers in the direction of the arrow on top of the cover, and then remove the cover completely.
- Wash out the interior of the drain tank.
- Close the water tank cover, and Re-attach it to the unit as original.
- Confirm the two locations are firmly inserted.
Add 200cc C around 1 cup) of water through the drain hole. (to prevent it from getting clogged)
- Use the unit after confirming that the water tank is in place.
WARNING
Before you clean the unit, turn off the power switch. Do not splatter water
on the unit.
Caution
- Wear gloves when cleaning.
- The antibacterial coating is effective when the bacteria exposed the coated surfaces (See the shade areas on the figure)
- The antibacterial coating becomes not effective when the surfaces get very dirty
Cleaning the air filter Around once a week
Remove the air filter
-
Pull the air filter out by the handle.
-
Cleaning the air filter
- Beat it lightly by hand or use a vacuum cleaner.
-
Re-attach to the unit.
- insert it all the way in, until it stops.(lf it is not in place, the dirt or dust will enter the unit and shorten its service life.)
Troubleshooting
If the following problems occur, please perform checks and fix.
| Problem | Check | Action |
|---|
No air blows even if hands are inserted
| Do the display indicators lights up?
Is the power switch on? Are you putting your hands all the way in?
|
- Turn the ground-fault circuit breaker on.
- Turn the power switch on.
- Put hands all the way in.
The unit does not stop blowing
|
Is the sensor blocked by the dirt or dust?
|
- Turn the power switch off, and then, after all the lamps in the display have gone off, remove the dust matter.
No hot air comes out
|
Heater is built-in, is the heater sensor dirty?
|
- Turn the power switch off. Remove the front cover, then remove the cover of terminal box, check the 3 fuses (terminal connector) whether burnt or not.
If the above actions do not work, turn off the power and the ground-fault circuit breaker, and call your dealer to inspect and repair it if necessary. (Costs are as per agreement with the dealer)
NOTICE ABOUT RECYCLING
Your product is designed and manufactured with high quality materials and
components which can be recycled and reused. This symbol means that electrical
and electronic equipment, at their end-of-life, should be disposed of
separately from your household waste. Please dispose of this equipment at your
local community waste collection/ recycling centre.
In the European Union there are separate collection systems for used
electrical and electronic products. Please help us to conserve the environment
we live in!.
DECLARATION OF CONFORMITY
Herewith, Amiridis Savvidis S.A. states that this product, complies with the requirements of below directives:
EMC Directive
14/30/EU Low Voltage Directive: 14/35/EU RoHS Directive: 11/65/EU & 15/863/EU
(E CE-marking Directive: 93/68/EEC The detailed declaration of conformity can
be found at www.morris.gr Exclusive importer in
Greece:
P.C. 55535 Thessaloniki
Greece T: +302310944944
F: +302310944940 www.amiridis-savvidis.gr
EXCLUSIVE DISTRIBUTOR
Amlrldla – Savldla S.A.
87 A, 17th November str.
55535, Pylea, Thessaloniki
Tel. 2310 944944
Fax. 2316 006650
www.morris.gr
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>