MATCO TOOLS MTCGLOWSPKR Wireless Vibe Light Speaker Instruction Manual

MATCO TOOLS MTCGLOWSPKR Wireless Vibe Light Speaker

Charge before use

This product can expose you to chemicals including nickel, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

Introduction

Thank you for purchasing the Matco Tools Vibe Speaker. This product is designed to provide high quality wireless sound for your computer, phone, tablet or any other wireless compatible audio device. Please follow these instructions carefully as improper use of the device can result in damage. Please read all safety and operating instructions thoroughly before installation and use and keep these instructions handy for future reference. Take special note of all warnings listed in these instructions and on the unit.

Included

1. Vibe speaker
2. USB cable (no adapter)
3. Remote control
4. Instruction manual

Specifications

Warning

• Although the Vibe Speaker is IP44 rated the power supply is not. It is recommended to charge the Vibe Speaker indoors. If the Vibe Speaker malfunctions, switch it off, unplug the power supply and contact your local authorized dealer.
  The rated voltage of the device is 100-240V 50/60Hz. Please do not exceed this voltage.

• Do not place the unit into water.

• Do not open or disassemble the unit.

• After charging, ensure the rubber seal cover is securely in place before using the Vibe Speaker

Charging

IMPORTANT : Before first use please allow the Vibe Speaker to charge fully

• The POWER indicator is red while charging and turns green when the battery is 90% or above 90% charged.
• The item comes with 1 piece of USB cable. Please use a suitable AC100-240V, DC 5V,1A adaptor to connect to the power source. Remarks : Depending on the model,  you may charge the Vibe Speaker by connecting the USB cable to a computer.

Operations by ON/OFF BUTTON

• Press ON/OFF button to turn on the Vibe Speaker and lights. You will hear a tone/jingle and the light is in “Slow flash” mode
• Activate the wireless function on your device and select MTCGLOWSPKR to connect

How to operate the ON/OFF switch

• Lightly press ON/OFF again and the light is in “Fast flash”
• Lightly press ON/OFF again and the light is in “Music flash”
• Lightly press ON/OFF again and the light will turn off but the music continues to play
• Lightly press ON/OFF again and the light is in “Fast flash”
• The cycle repeats itself – To turn off the Vibe Speaker, press ON/OFF for 5 seconds.

Connecting a wireless compatible device

• When the Vibe Speaker is in working mode,you can press ON/OFF switch at the back OR to use a Remote Control to turn on the speaker and to activate the wireless function on the mobile phone by connecting it to MTCGLOWSPKR.
• You will hear a tone/jingle when the wireless function is successfully connected.

Remarks

1. Disconnected prompt note : A tone/jingle
2. Maximum volume prompt note : A beep sound
3. Low battery prompt note : A low beep sound
4. Low battery power indication. When low battery power is detected, the “low battery” prompt note will prompt every 3 minutes. It will continue 3 times before shutting down.

Remote control illustrations

Please pull away the PVC protection film from the battery before using the remote control.

Troubleshooting

• If the Vibe Speaker does not turn on -The battery may have completely run out. Connect the Vibe Speaker to a power source and wait for 30 minutes for the Vibe Speaker to be partially charged.
• Volume too low -Increase the volume setting on the music source .e.g. mobile phone.
• he recording may have lower volume. Try a different recording.
• The battery may be running low. Connect the power adapter to charge the battery

Distorted Sound

• The quality of the audio that you are playing affects the quality of the audio the Vibe Speaker produces. The Vibe Speaker is a high-performance audio reproduction system, a distortion that you did not hear before may become evident in the Vibe Speaker.
• Changing your audio to a high quality file or format will allow you to hear a higher quality signal.
• The Vibe Speaker cannot correct any deficiency in the audio source. – Lower the volume on the source device and /or the Vibe Speaker
• Ensure the surface where the Vibe Speaker is sitting is not interfering with the sound.
• The battery may be running low. Recharge the battery.
• Water may have seeped into the Vibe Speaker. Turn the Speaker upside-down and let the water drain through the protective mesh.

Unresponsive to user input

If the Vibe Speaker becomes unresponsive to any user input ( does not turn off, keys not responding, cannot stop or start audio streaming) let the Vibe Speaker discharge its battery and this will reset the device.

Important

If/when disposing of the Vibe Speaker, please obtain information on battery disposal from your local authority.

References

• P65Warnings.ca.gov

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>