viveroo REV20200325 Loop Ipad Docking Station Ipad Wall Mount Rotatable User Manual
- June 9, 2024
- viveroo
Table of Contents
REV20200325 Loop Ipad Docking Station Ipad Wall Mount Rotatable
Product Information
The Loop is a product that comes with a user manual, loop
Mounting Set, external cable, power supply, and mounting screws. It
is intended for use in enclosed and dry living spaces with a
maximum altitude of 2,000m. The installer is responsible for
selecting the proper mounting location and safe installation of the
Loop. All electrical installation work must be conducted by
authorized, trained electricians, always adhering to the general
rules and regulations applying to electrical installation. The Loop
low voltage power consumption is 12 Vdc 18 Watt.
Technical Data:
- Diameter design cover in mm: 385
- Depth loop: 39
- Diameter opening (for furniture installation): 351
- Diameter opening (for flush-mounted box): 363
- Installation depth loop (for furniture installation): 30
- Installation depth loop (for flush mounting): 66
- Weight in kg: 4.8
- Overvoltage category: 16A (EU), 20A (USA/Canada) OVC II
- Wire crosssection: CE & Co.
- All loops have CE certification. Loop is quality Made in
Germany.
Product Usage Instructions
Before using the Loop, please read the assembly instructions
carefully and the user manual completely. Follow the instructions
and recommendations to ensure proper use and maximum enjoyment. The
Loop and all Loop mounting sets are intended for use in enclosed
and dry living spaces only. Installation, service or repairs, if
necessary, may only be performed by authorized persons.
Safety Information:
-
The installer is responsible for selecting the proper mounting
location and safe installation of the Loop. -
This also applies to installation in movable parts, such as
doors. The installer is responsible for performing and documenting
all necessary safety tests. -
All electrical installation work may only be conducted by
authorized, trained electricians, always adhering to the general
rules and regulations applying to electrical installation. -
Wire end sleeves and ferrules must be used for flexible
cables. -
Should it become apparent that safe operation of Loop is not
assured, then Loop must immediately be taken out of service and
secured against potential misuse. -
If the Loop functions are limited, blocked or disabled, if an
unusual odor is present, if noises such as scratching are audible
or damage is visible, safe operation can no longer be
guaranteed.
Operation:
-
To go from vertical to horizontal format, spin the Loop to the
left. From horizontal to vertical, spin the Loop to the right. -
A recessed handle is created by applying gentle pressure on the
Loop button. Now you can easily spin the Loop from horizontal to
vertical and back again with just the touch of a finger. -
Thanks to the SoftClose function, Loop will automatically
complete the rotation just before reaching its final resting
position.
Removal from power supply:
Loop may be removed from the power supply via the circuit
breaker in the respective rooms.
Note:
Operation of Loop without a Mounting Set will lead to immediate
loss of guarantee and warranty.
User manual
loop
viveroo GmbH Wewelsburger Straße 4 33154 Salzkotten Germany www.viveroo.de
REV20200325
User manual loop, page 1 of 8
Safety information
!WARNING
Please read the assembly instructions included carefully. Please
read this loop user manual completely before using your loop. Please follow the instructions and recommendations to ensure proper use and maximum enjoyment.
!
Safety information
loop and all loop mounting sets are intended for use in enclosed and dry living spaces.
The following conditions must be provided: – Operating temperature between 0°
C (32° F) and 35° C (95° F). – Relative humidity (during use): 20 % to 90 %,
non-condensing. – No external environmental influences such as oil, chemicals,
salt,
extensive dust, etc.
The maximum altitude is 2.000m.
Installation, service or repairs, if necessary, may only be performed by authorized persons.
The installer is responsible for selecting the proper mounting location and safe installation of loop. This also applies to installation in movable parts, such as doors. The installer is responsible for performing and documenting all necessary safety tests.
All electrical installation work may only be conducted by authorized, trained electricians, always adhering to the general rules and regulations applying to electrical installation. Wire end sleeves and ferrules must be used for flexible cables.
Should it become apparent that safe operation of loop is not assured, then loop must immediately be taken out of service and secured against potential misuse. If the loop functions are limited, blocked or disabled, if an unusual odor is present, if noises such as scratching are audible or damage is visible, safe operation can no longer be guaranteed.
User manual loop, page 2 of 8
Technical Data
Product contents
Compatability
– User manual loop – loop
Please note! External cable, power supply and mounting screws are included in
loop MountingSet.
Electrical operation of loop is permitted only in connection with loop
Mounting Set and power supply and cable included in the Mounting Set.
Operation of loop without a Mounting Set will lead to immediate loss of
guarantee and warranty.
Measurements Diameter design cover in mm
Depth loop
Diameter opening (for furniture installation) Diameter opening (for flush-
mounted box)
Installation depth loop (for furniture installation)
Installation depth loop (for flush mounting)
Weight in kg
Electrical connections
loop low voltage Power consumption
385
39 351 363
30
66
4,8 12 Vdc 18 Watt
Removal from power supply
loop may be removed from the power supply via the circuit breaker in the respective rooms.
Circuit Breaker
Overvoltage category
16A (EU) , 20A (USA/Canada) OVC II
wire crosssection
CE & Co.
The permitted conductive cross-section is between 0.75mm² and 2.5mm².
All loops have CE certification. loop is quality “Made in Germany”. We use
only high-quality parts and components produced by market leaders. loop
customers are proud of their iPad Garage.
*) Technical changes and mistakes are excepted. iPad is a registered trademark of Apple Inc.
User manual loop, page 3 of 8
Operation
Functions
loop It! 90° Rotation
A recessed handle is created by applying gentle pressure on the loop button.
Now you can easily spin the loop from horizontal to vertical and back again
with just the touch of a finger.
To go from vertical to horizontal format, spin the loop to the left. From
horizontal to vertical, spin the loop to the right.
Thanks to the SoftClose function, loop will automatically complete the
rotation just before reaching its final resting position.
Click It! Opening the iPad shelf
Open the iPad resting shelf by using the loop button. ! IMPORTANT: The iPad
must be in vertical position. ! IMPORTANT: loop must be installed vertically
to open the resting shelf, i.e. wall. – the suspension of the resting shelf
has been set to this position. For horizontal (i.e. table) or diagonal (i.e.
lectern, teacher’s desk, control panel) installation, special adapter sets are
available on request.
Care and Cleansing
Cleanse your loop as needed with a soft micro fiber cloth and clear water only. Dampen the micro fiber cloth and wipe the surfaces gently. If necessary, you may remove the rubber pads (see ,,Installation”). The glass surfaces of DeepBlack and ClearWhite may also be cleaned with standard glass cleaners. ! WARNING: The interior of the loop must remain dry. To ensure this, use only a damp cloth for cleansing. ! WARNING: Never scratch, scrape or scrub loop surfaces with abrasive materials.
User manual loop, page 4 of 8
Installation
Use the corresponding MountingSet to install your loop. All MountingSets come
with specific mounting instructions.
Step 1
Carefully remove the four screws on the cover (green). Carefully remove the cover by lifting it towards you and place the cover in a safe spot. ! IMPORTANT: Hold cover tightly when removing the final screw to avoid damage from falling down.
Step 2
Plug the connecting cable from the MountingSet into the loop plug contact (red). ! WARNING: Do not run the connecting cable through the inner section of the loop because it can easily block and damage the rotating function.
Step 3
The various fastening points for the loop are easily identifiable. Using the screws included in the MountingSet, fasten the loop as follows: – Red: Inwall- Mounting with flush mounting box – Green: Furniture and door mounting ! IMPORTANT: Please follow the instructions included with the MountingSet.
Step 4
Place the cover on the loop. Important: The correct positioning is dictated by the button. Thread the cover into place there. Fasten the cover with the four screws and put the inlays back in place.
User manual loop, page 5 of 8
Warranty
Warranty
Warranty claims and verification Warranty exceptions
loop comes with a one year warranty from date of purchase by the original end
customer, unless the device was repaired or replaced during the warranty
period. In this case, the warranty is valid until the end of the regular two
year warranty or six months following the repair/replacement, whichever comes
first.
Should your loop for any reason not perform as expected, please contact your
dealer and provide the original invoice with serial number as well as a brief
description of your complaint.
The following devices are excluded from the warranty Devices with damages
caused by:
– acts of nature,
– misuse, including but not limited to disregarding the user manual and
mounting instructions,
– inappropriate handling,
– connection to an incorrect power supply,
– repairs or attempted repairs by unauthorized persons,
– use of the device in connection with third party products,
– devices on which the serial number of the producer has been changed,
deleted, removed or made illegible.
User manual loop, page 6 of 8
security system (optional)
LockingSystem security, PIN controlled opening with viverooApp
1 Your viverooDock is already locked by default. A metal pin behind the button
prevents pressing the knob and thus opening the iPad shelf. To unlock your
Dock the viveroo App “SecurityDock” is required. Go to the App Store, search
for ,,viveroo” and download the app. The app controls your viverooDock via
Bluetooth. Therefore you can use any iOS device to unlock your Dock, in
addition to the iPad which is inside.
2 When you open the app for the first time you have to set a password. Choose
a safe password and confirm with ,,Signup”. If you have an iOS device with
Touch ID (iPhone 5s or later or iPad Air 2) you can also use your fingerprint
to unlock.
User manual loop, page 7 of 8
security system (optional)
LockingSystem security, PIN controlled opening with viverooApp
3 Now you will be redirected to a dashboard where all your available
viverooDocks are being displayed.
! IMPORTANT: Connect your viverooDock to the power supply so that the
Bluetooth module can send out a signal and is displayed in the app. !
Additionally, activate Bluetooth on your iOS device.
4 Tap the image of your Dock. Your camera is now activated, please allow
access for using your camera. To pair your iOS device and your viverooDock,
scan the QR code on the included key card. This procedure is necessary only
once, after the first pairing the devices are able to communicate with each
other. A message indicates the successful pairing of the devices. ! IMPORTANT:
Please keep the key card in a safe place. For pairing a new iOS device or
resetting the password it is needed again. The key cards are also archived by
viveroo and can be requested at any time.
5 When you now tap your viverooDock, the pin is magnetically attracted and
unlocks the dock. Then you can press the button and open the iPad shelf. The
time slot in which the dock is unlocked, is 5 seconds. After that, the dock is
locked with an audible click again.
A tap on the little “i” next to the dock allows you to make some adjustments,
such as the model, color or the name of the dock.
User manual loop, page 8 of 8
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>