viveroo Square Tablet Mount Ipad Wall Mount Instruction Manual

viveroo Square Tablet Mount Ipad Wall Mount Instruction Manual

Inwall, square

viveroo GmbH
We wel s burger Straß e 4
33154 Salzkotten
Germany
www.viveroo.de

Safety information

!ATTENTION Please read the assembly instructions included carefully before installing the Mounting Set. Please also read the square user manual completely before using your square. Please follow the instructions and recommendations to ensure proper use and maximum enjoyment.

Safety information
square and all square mounting sets are intended for use in enclosed and dry living spaces.

The following conditions must be provided:

• Operating temperature between 0° C (32° F) and 35° C (95° F).
• Relative humidity (during use): 20 % to 90 %, non-condensing.
• No external environmental influences such as oil, chemicals, salt, extensive dust, etc.

The maximum altitude is 2.000m.

Installation, service or repairs, if necessary, may only be performed by authorized persons.

The installer is responsible for selecting the proper mounting location and safe installation of square. This also applies to installation in movable parts, such as doors. The installer is responsible for performing and documenting all necessary safety tests.

All electrical installation work may only be conducted by authorized, trained electricians, always adhering to the general rules and regulations applying to electrical installation. Wire end sleeves and ferrules must be used for flexible cables.

Should it become apparent that safe operation of square is not assured, then square must immediately be taken out of service and secured against potential misuse. If the square functions are limited, blocked or disabled, if an unusual odor is present, if noises such as scratching are audible or damage is visible, safe operation can no longer be guaranteed.

Technical Data

Product contents

• Installation guide Inwall
• square flush mounting box
• Power supply (IN 100-240 Vac, 50-60 Hz, OUT 12 Vdc) with pre-installed square power cable (including usage guidelines and installation guide)
• Fastening screw packet for attaching square

Compatibility

Electrical operation of square is permitted only in connection with square Mounting Set and power supply and cable included in the Mounting Set. Operation of square without a Mounting Set will lead to immediate loss of guarantee and warranty.

*) Technical changes and mistakes are excepted.
iPad is a registered trademark of Apple Inc.

Installation guide

Technical Details

square
Measurements for installation in drywall, stone or solid wall (with wallbox), in mm

Cutting Measurements for installation in drywall, stone or solid wall (with wallbox), in mm

Square with network connection

It is possible to equip the square with a network interface. This must be ordered in conjunction with the square and can not be retrofitted.

MountingSet Inwall zero square

Incl. MountingSet Inwall + flush mount frame with reinforcing grid

Safety informaion
! Important:
Before installing this MountingSet please read the following information. Follow the instructions and recommendations described.

General conditions:
The MountingSet Inwall zero is an extension of MountingSet Inwall. Accordingly, it is assumed that both products are built in combination.

The following embedding materials are approved for the attachment and incorporation of MountingSet Inwall zero: mineral plaster, polymer modified adhesive and reinforcement cement.
The MountingSystem is designed for installation in dry and closed living spaces.
The following environmental conditions are ensured:
Ambient temperature 0 °C to 35 °C
No environmental influences, such as oil, chemicals, salt and comparable
No direct sunlight

The MountingSet must be processed and installed only by authorized personnel. This includes the proper installation of electrical connections. The responsibility for proper installation and safe installation of the mounting system is only with the processor. Basically, the user has to make and certify all safety checks.

Delivery contents

• Installation guide, flush-plastered MountingSet Inwall zero
• Flush mount frame with reinforcing grid

Installation in hollow walls (plasterboard)
Make an angular opening in the wall: Measurements for portrait: 271mm length, 344mm height. Measurements for landscape: 344mm length, 271mm length. The depth should be approximately 76mm. Place the power cable.

Clean the surface of the gypsum board thoroughly and fix the flush mount frame on the gypsum fibreboard – pay attention that the flush mount box is fastened parallel to the surface and is not shifted or offset in the wall.

! Important: The gypsum fibreboard must provide a very smooth, surface adhesion for the flush mount frame, stressand distortion-free!

Incorporate the flush mount frame with approved embedding material (see above). To do this, prepare the surface according to VOB, Section C, DIN 18363, DIN 18350 or BFS notices. Then apply the embedding material evenly to the gypsum fibreboard according to the manufacturer’s instructions. Embed the reinforcement fabric of the frame in the wet
coating without any creases. After that apply embedding material again evenly, so that the grid is no longer visible.

Depending on the design ideas the flush mount frame can be plastered up to the upper edge.
After the embedding material has perfectly dried out, please clean the inner surfaces of the frame and insert the wall case / flush mount box. Please follow the installation guide for the MountingSet Inwall.

! Attention: Install the flush box so deep that it rests firmly on the inner ring of the frame.
! Attention: Screw the wall case / flush mount box so tight that it stabilizes the frame.

MountingSet Inwall zero square
Incl. MountingSet Inwall + flush mount frame with reinforcing grid
REV20180809

Installation in brick walls and concrete walls (shell)
Make an angular opening in the wall: Measurements for portrait: 271mm length, 344mm height. Measurements for landscape: 344mm length, 271mm length. The depth should be approximately 76mm. Place the power cable. Apply subsoil / substrate plaster to the wall and fix the flush mount frame – pay attention that the flush mount box is fastened parallel to the surface and is not shifted or offset in the wall.

! Important: The subsoil / substrate plaster must provide a very smooth, surface adhesion for the flush mount frame, stress- and distortion-free!

Incorporate the flush mount frame with approved embedding material (see above). To do this, prepare the surface according to VOB, Section C, DIN 18363, DIN 18350 or BFS notices. Then apply the embedding material evenly to the gypsum fibreboard according to the manufacturer’s instructions. Embed the reinforcement fabric of the frame in the wet coating without any creases. After that apply embedding material again evenly, so that the grid is no longer visible.

Depending on the design ideas the flush mount frame can be plastered up to the upper edge.
After the embedding material has perfectly dried out, please clean the inner surfaces of the frame. Insert the wall case / flush mount box and fix it with fastening material such as plaster or mortar or cement – Please follow the installation guide for the MountingSet Inwall.

! Attention: Install the flush box so deep that it rests firmly on the inner ring of the frame.
! Attention: Screw the wall case / flush mount box so tight that it stabilizes the frame.

Images for illustration

Information:
Follow sequence: 1. Flush mount frame , 2. flush mount box , 3. square

Install the flush box so deep that it rests firmly on the inner ring of the frame.

Information
When installed, the square forms a flat surface with the wall. There is a 1mm wide shadow gap (red) around the square.

Sectional drawing

MountingSet Furniture for loop and square

Safety Information

!ATTENTION Please read the assembly instructions included carefully before installing the MountingSet. Please also read the loop user manual completely before using your loop. Please follow the instructions and recommendations to ensure proper use and maximum enjoyment.

Safety information
loop and all loop mounting sets are intended for use in enclosed and dry living spaces.

The following conditions must be provided:

• Operating temperature between 0° C (32° F) and 35° C (95° F).
• Relative humidity (during use): 20 % to 90 %, non-condensing.
• No external environmental influences such as oil, chemicals, salt, extensive dust, etc.

The maximum altitude is 2.000m.
Installation, service or repairs, if necessary, may only be performed by authorized persons.
The installer is responsible for selecting the proper mounting location and safe installation of loop. This also applies to installation in movable parts, such as doors. The installer is responsible for performing and documenting all necessary safety tests.

All electrical installation work may only be conducted by authorized, trained electricians, always adhering to the general rules and regulations applying to electrical installation. Wire end sleeves and ferrules must be used for flexible cables.

Should it become apparent that safe operation of loop is not assured, then loop must immediately be taken out of service and secured against potential misuse. If the loop functions are limited, blocked or disabled, if an unusual odor is present, if noises such as scratching are audible or damage is visible, safe operation can no longer be guaranteed.

Technical data

Technical Details

square

Measurements for installation in furniture, cabinets, wooden materials, in mm

Technical Details
square

Cutting Measurements, in mm

Read More About This Manual & Download PDF:

References

• iPad Halterung - iPad Wandhalterung und iPad Ständer | viveroo

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>