viveroo REV20200301 Square Tablet Mount Ipad Wall Mount User Manual
- June 9, 2024
- viveroo
Table of Contents
User manual square
User manual square, page of 1 9
Safety information
! WARNING
Please read the assembly instructions included carefully. Please read this
square user manual completely before using your square. Please follow the
instructions and recommendations to ensure proper use and maximum enjoyment.
! Safety information square and all square mounting sets are intended
for use in enclosed and dry living spaces.
The following conditions must be provided:
– Operating temperature between 0° C (32° F) and 35° C (95° F).
– Relative humidity (during use): 20 % to 90 %, non-condensing.
– No external environmental influences such as oil, chemicals, salt, extensive
dust, etc.
The maximum altitude is 2.000m.
Installation, service or repairs, if necessary, may only be performed by
authorized persons.
The installer is responsible for selecting the proper mounting location and
safe installation of square. This also applies to installation in movable
parts, such as doors. The installer is responsible for performing and
documenting all necessary safety tests.
All electrical installation work may only be conducted by authorized, trained
electricians, always adhering to the general rules and regulations applying to
electrical installation. Wire end sleeves and ferrules must be used for
flexible cables. Should it become apparent that safe operation of square is
not assured, then square must immediately be taken out of service and secured
against potential misuse. If the square functions are limited, blocked or
disabled, if an unusual odor is present, if noises such as scratching are
audible or damage is visible, safe operation can no longer be guaranteed.
Technical Data
Product| – User manual square
– square
---|---
contents| Please note! External cable, power supply and mounting screws
are included in square MountingSet.
Compatibility| Electrical operation of square is permitted only in
connection with square MountingSet and power supply and cable included in the
Mounting Set. Operation of square without a MountingSet will lead to immediate
loss of guarantee and warranty.
Measurements| Measurements design cover
Depth square
Size of opening (for furniture installation)
Size of opening (for flush-mounted box)
Installation depth (for furniture installation)
Installation depth (for flush-mounted box)
Weight in kg| square
Electrical connections| Low voltage
Power consumption
Removal from power supply| square may be removed from the power supply
via the circuit breaker in the respective rooms.
Circuit Breaker| 16A (EU) , 20A (USA/Canada)
Overvoltage category| OVC II
wire crosssection| The permitted conductive cross-section is between 0.75mm²
and 2.5mm².
CE & Co.| All squares have CE certification. square is quality “Made in
Germany”. We use only high quality parts and components produced by market
leaders. square customers are proud of their iPad Garage.
Technical changes and mistakes are excepted.
iPad is a registered trademark of Apple Inc.
Operation
Functions
Opening the iPad shelf
Open the iPad resting shelf by using the square button. Now you can remove or
insert your iPad.
! IMPORTANT: square can be either installed vertically or horizontally.
The suspension of the resting shelf has been set to wall position. For
horizontal (i.e. table) or diagonal (i.e. lectern, teacher’s desk, control
panel) installation, special adapter sets are available on request.
Care and Cleansing
Cleanse your square as needed with a soft micro fiber cloth and clear water
only. Dampen the micro fiber cloth and wipe the surfaces gently. If necessary,
you may remove the rubber pads (see “Mounting”). The glass surfaces of
DeepBlack and ClearWhite may also be cleaned with standard glass cleaners.
! WARNING: The interior of the square must remain dry. To ensure this, use
only a damp cloth for cleansing.
! WARNING: Never scratch, scrape or scrub square surfaces with abrasive
materials.
Installation
Use the corresponding MountingSet to install your square. All MountingSets
come with specific mounting instructions.
Step 1
Carefully remove the four screws on the cover (see photo – green).
! IMPORTANT: Hold cover tightly when removing the final screw to avoid
damage from falling down.
Carefully remove the cover by lifting it towards you and place the cover in a
safe spot.
Step 2
Plug the connecting cable from the MountingSet into the square plug contact.
! WARNING: When inserting the square, make sure that the connecting cable
is not pinched or pulled, as this may damage the cable.
! WARNING: If a power supply is located close to the square, please
connect the protective grounding wire (yellow) to the protective conductor
of the power supply (for example InWall MountingSet).
Step 3
The various fastening points for the square are easily identifiable (red).
Using the screws included in the MountingSet, fasten the square.
! IMPORTANT: Please follow the instructions included with the MountingSet.
Step 4
Place the cover on the square. The correct positioning is dictated by the
button. Thread the cover into place there. Fasten the cover with the four
screws and put the upper and lower inlays in place.
Warranty
Warranty| square comes with a one year warranty from date of purchase by
the original end customer, unless the device was repaired or replaced during
the warranty period. In this case, the warranty is valid until the end of the
regular two year warranty or six months following the repair/replacement,
whichever comes first.
---|---
Warranty claimsand verification| Should your square for any reason not
perform as expected, please contact your dealer and provide the original
invoice with serial number as well as a brief description of your complaint.
Warranty claimsand verification| The following devices are excluded from
the warranty
Devices with damages caused by:
– acts of nature,
– misuse, including but not limited to disregarding the user manual and
mounting instructions,
– inappropriate handling,
– connection to an incorrect power supply,
– repairs or attempted repairs by unauthorized persons,
– use of the device in connection with third party products,
– devices on which the serial number of the producer has been changed,
deleted, removed or
made illegible.
security system (optional)
LockingSystem security, PIN controlled opening with viverooApp 
-
Your viverooDock is already locked by default. A metal pin behind the button prevents pressing the knob and thus opening the iPad shelf. To unlock your Dock the viveroo App “SecurityDock” is required. Go to the App Store, search for „viveroo“ and download the app.
The app controls your viverooDock via Bluetooth. Therefore you can use any iOS device to unlock your Dock, in addition to the iPad which is inside. -
When you open the app for the first time you have to set a password. Choose a safe password and confirm with „Signup“. If you have an iOS device
with Touch ID (iPhone 5s or later or iPad Air 2) you can also use your fingerprint to unlock.
-
Now you will be redirected to a dashboard where all your available viverooDocks are being displayed.
! IMPORTANT: Connect your viverooDock to the power supply so that the Bluetooth module can send out a signal and is displayed in the app.
! Additionally, activate Bluetooth on your iOS device. Tap the image of your Dock. Your camera is now activated, please allow access for using your camera. -
To pair your iOS device and your viverooDock, scan the QR code on the included key card. This procedure is necessary only once, after the first pairing the devices are able to communicate with each other. A message indicates the successful pairing of the devices.
! IMPORTANT: Please keep the key card in a safe place. For pairing a new iOS device or resetting the password it is needed again. The key cards are also archived by viveroo and can be requested at any time. -
When you now tap your viverooDock, the pin is magnetically attracted and unlocks the dock. Then you can press the button and open the iPad shelf. The time slot in which the dock is unlocked, is 5 seconds. After that, the dock is locked with an audible click again.
A tap on the little “i” next to the dock allows you to make some adjustments, such as the model, color or the name of the dock.
-
LAN network connection
(optional)
It is possible to equip the square with a network interface. This must be
ordered in conjunction with the square and can not be retrofitted.
The installation of the square and the connection to the power supply and CAT
cable can be found in the installation instructions.
Once the iPad is put into the square, the iPad is connected by cable to the
home network. In the iPad App System Settings a new menu item “Ethernet”
appears. There are various options for configuring IP addresses, DNS and proxy
servers. If the iPad is removed, the menu item disappears and the iPad is
again connected to the network via WLAN.
User manual square, page of 9 9
viveroo GmbH
Wewelsburger Straße 4
33154 Salzkotten
Germany
www.viveroo.com,
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>