Discover CAN BUS Type-B Battery Discharge Indicator User Guide
- June 9, 2024
- Discover
Table of Contents
- Discover CAN BUS Type-B Battery Discharge Indicator
- INTRODUCTION
- INSTALLATION OPTIONS AND REQUIRED MATERIALS
- ELECTRICAL OVERVIEW
- MECHANICAL (mm)
- BATTERY PINOUT ASSIGNMENTS
- BDI TYPE-B ENVIRONMENTAL SPECIFICATIONS
- INSTALLATION
- BATTERY MODELS
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Discover CAN BUS Type-B Battery Discharge Indicator
INTRODUCTION
The Type-B Battery Discharge Indicator (BDI) communicates with Discover Lithium batteries over CAN Bus using the LYNK Port on LITHIUM PROFESSIONAL or AEBus Port on AES LiFePO4 Industrial batteries. The TYPE-B BDI displays warnings, charging status, and state-of-charge (SOC) using incremental LED SEGMENTS. The BDI device is plug and play, deriving both power and battery status directly from the LYNK Port or AEBus Port. The TYPE-B BDI will provide the aggregate SoC for up to 20 Discover Lithium Batteries. The Type-B BDI is rated IP 30, with an installed frontal rating of IP 65.
Compatible Batteries
- AES LiFePO4 Industrial Batteries: 12-48-6650, 12-36-6700, 14-24-2800, 14-36-3000, 14-48-3000
- LITHIUM PROFESSIONAL Batteries: DLP-GC2-12V, DLP-GC2-24V, DLP-GC2-36V, DLP-GC2-48V 2.0
INSTALLATION OPTIONS AND REQUIRED MATERIALS
The Type-B Battery is available as a head unit (950-0034) and used with AES LiFePO4 or LITHIUM PROFESSIONAL batteries. The installer must supply a cable of the appropriate length with a pinout and connector appropriate for either an AES LiFePO4 Industrial battery or a LITHIUM PROFESSIONAL battery. Refer to section 6.0 Battery Pinout Assignments for details on connectors and pinouts.
A kit (950-0039) that includes both the TYPE-B head unit (950-0034) and an LYNK NETWORK BDI 1.8M cable (790-0079) is available from Discover for installation with LITHIUM PROFESSIONAL batteries.
LED INDICATORS
Normal Operation
Only 1 LED will be on during regular operation.
Position | Activity |
---|
LED 1
| Flash – State of Charge 0% to 9 %
Solid on – State of Charge range 10% to 19 %
LED 2| Solid on – State of Charge range 20% to 29 %
LED 3| Solid on – State of Charge range 30% to 39 %
LED 4| Solid on – State of Charge range 40% to 49 %
LED 5| Solid on – State of Charge range 50% to 59 %
LED 6| Solid on – State of Charge range 60% to 69 %
LED 7| Solid on – State of Charge range 70% to 79 %
LED 8| Solid on – State of Charge range 80% to 89 %
LED 9| Solid on – State of Charge range 90% to 94%
LED 10| Solid on – State of Charge range 95% to 100%
Charging Operation
The active State of Charge LED will slowly flash
Battery Protection Indication
When a connected battery has active protection (faults), LED 1 through LED 10
will all flash at the same time.
No Battery Detected
The LED interface will continuously cycle through all LEDs when the BDI-B is
powered on, but no batteries are detected.
ELECTRICAL OVERVIEW
MECHANICAL (mm)
Pinout Assignments for BDI (MOLEX 39-28-1083)
Pin 1 | LYNK Bus (AEBus) CAN High |
---|---|
Pin 5 | LYNK Bus (AEBus) CAN GND |
Pin 6 | LYNK Bus (AEBus) CAN +12V * |
Pin 8 | LYNK Bus (AEBus) CAN Low |
BATTERY PINOUT ASSIGNMENTS
Pinout Assignments for AES LiFePO4 Industrial Batteries
Pin 3 | LYNK Bus (AEBus) CAN GND |
---|---|
Pin 4 | LYNK Bus (AEBus) CAN High |
Pin 5 | LYNK Bus (AEBus) CAN Low |
Pin 12 | LYNK Bus (AEBus) CAN +12V * |
- Not all models are equipped with an internal 12V power supply.
Pinout Assignments LITHIUM PROFESSIONAL Batteries
IEC M12 A-Coding 5 Pin
PIN Number | Function |
---|---|
1 | ON/OFF Switch |
2 | LYNK Bus CAN L |
3 | LYNK Bus CAN H |
4 | LYNK Bus 12V + |
5 | LYNK Bus GND |
BDI TYPE-B ENVIRONMENTAL SPECIFICATIONS
- Operation: -40°C to 85°C (-40°F to 185°F)
- Storage: -50°C to 90°C (-58°F to 194°F)
- Humidity: 95 % RH non-condensing at 38°C (100°F)
Rated IP 30, with an installed frontal rating of IP 55 when installed with provided gasket.
INSTALLATION
Gasket Mounting – Front or Back Secure BDI with M 2.5 bolts or screws.
Connect Harness
Connect the cable harness to either LYNK Port or AEbus Port on the battery,
then connect to TYPE-B BDI.
BATTERY MODELS
AES LIFEPO4 INDUSTRIAL BATTERIES:
- 12-48-6650
- 12-36-6700
- 14-24-2800
- 14-36-3000
- 14-48-3000
LITHIUM PROFESSIONAL BATTERIES:
- DLP-GC2-12V
- DLP-GC2-24V
- DLP-GC2-36V
- DLP-GC2-48V
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>