Everbloom E213612 Deep Trough Planter Box Installation Guide

: June 9, 2024
: Everbloom

Table of Contents

Everbloom E213612 Deep Trough Planter Box
Product Information
Product Usage Instructions
Parts List
Assembly
Parts include
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Everbloom E213612 Deep Trough Planter Box

Product Information

Deep Trough Planter Box

The Deep Trough Planter Box is perfect for creating an elevated vegetable garden or planter. The box has a maximum load capacity of approximately 4 cu. ft. of soil and comes with small parts that should be kept away from children and pets. The model number for the planter box is E213612 / E213612G and its dimensions are 36 L x 12 W x 21 H. The package includes all the necessary parts required for assembly, including corner posts, long and short boards, and bottom boards.

Product Usage Instructions

Assembly

Before You Start: Read the instructions carefully and find a suitable space to assemble the planter box. You need at least 37 x 13 (94 x 33cm) for the finished product. A flat and firm area like a garage floor or flat yard space is perfect! The only tool you may need is a rubber mallet.
Parts List: Check the parts list to ensure that all the necessary parts are included in the package.
Assembly: Eleven depths are available by changing the sequence of the boards and position of the bottom boards, as shown in the images on page 3. Follow the steps according to the depth you want to achieve.
- Depth of 2.5, 5, 7.25, 9.5,9.75, 12, 14.4 and 17: Refer to steps from page 4.
- Depth of 4.75, 7 and 11.9: Refer to steps from page 10.
Assembly for Deeper Planting Depths of 17:
Follow the steps below:
Make sure each corner post is oriented correctly, as shown in Image 3 on page 4.
Slide one short board A into the corner brackets from above.
Note that the short boards need to be placed in the inward U shape of the brackets, as shown in Image 4 on page 4.
Slide another short board A into the other two corner brackets from above, as shown in Image 5 on page 5.

Once you have assembled the Deep Trough Planter Box, you can start planting your favorite vegetables or flowers and enjoy your elevated garden or planter! For any questions or comments, please email us at service@everbloom- garden.com. Don’t forget to subscribe at www.everbloom-garden.com for extra savings and upgrading information!

Thank You!

You’re only a few steps away from your perfect vegetable garden or elevated planter. We hope you enjoy!

Before You Start

Please read the instructions carefully to familiarize yourself with every detail and step involved. Keep this manual for future reference. Find a suitable space to assemble your new Trough Planter Box.
You need at least 37” x 13” (94 x 33cm) for the finished product. A flat and firm area (like a garage floor or flat yard space) is perfect! The only tool you may need is a rubber mallet.

Important Notes

Small parts are included; we advise you to keep them away from children and pets.
We also suggest having another person help you assemble. Maximum Load Capacity: approximately 4 cu. ft. of soil
Subscribe at www.everbloom-garden.com for extra savings and upgrading information!

Everbloom-Garden.com

Questions or Comments?
Email us at service@everbloom-garden.com
Model# E213612 / E213612G
- Dimensions 36″ L x 12″ W x 21″ H

Parts List

Deep Trough Planter Box – 36″ L x 12″ W x 21″ H

Assembly

Deep Trough Planter Box – 36″ L x 12″ W x 21″ H

Eleven depths are available by changing the sequence of the boards and position of the bottom boards, as shown in below images.
You can choose according to different needs first.
For depth of 2.5”, 5”, 7.25”, 9.5“, 9.75”, 12”, 14.4” and 17” as shown in Image 1, 2, 3 and 4, please refer to steps from page 4.
For depth of 4.75”, 7” and 11.9” as shown in Image 2, 3 and Image 4, please refer to steps from page 10.
For the deeper planting depths of 17”, please follow steps below.
For other depths, the assembly methods are similar, just pay attention to the sequence of the boards and position of the bottom boards, please refer to.
Start by making sure each corner post is oriented correctly, as shown in Image 3. Slide one short board A into the corner brackets from above.
Note: The short boards need to be placed in the inward “U” shape of the brackets, as shown in Image 4.
Slide another short board A into the other two corner brackets from above, as shown in Image 5.
With the help of another person holding the 2 assembled parts, slide the 2 long support boards into the brackets from above. Make sure that one support board goes straight to the bottom, while the other one stays in the middle of the way (don’t push it to the bottom), with the top edge between the 4th and 5th holes of the post.
Put the bottom boards on the lower slot of long support boards. Make sure the 2 ends of these bottom boards go into the slot and rest in them with enough contact as shown in Image 7. Adjust the height of the higher long support board slightly to hold these bottom boards if necessary.
Push down the higher long support board to the bottom, as shown in Image 8.
Slide the remaining boards into place, as shown in Image 9. Now you get an trough planter box with 17” planting depth. Then, go to page 15, and follow the steps afterwards.
Note: If you want to add trellis kit onto this bed, please assemble the extension connectors before this step, to avoid disassembling the boards later.
For the planting depth of 11.9”, please follow steps below.
For depth of 4.75” or 7”, the assembly methods are similar, just pay attention to the sequence of the boards and position of the bottom boards, please refer to.
Start by making sure each corner post is oriented correctly, as shown in Image 3a. Slide one short board B into the corner brackets from above.
Note: The short boards need to be placed in the inward “U” shape of the brackets, as shown in Image 4a.
Slide another short board A into the other two corner brackets from above, as shown in Image 5a.
With the help of another person holding the 2 assembled parts, slide the 2 long support boards into the brackets from above to the bottom, as shown in Image 6a.
Put the bottom boards on the long support boards, as shown in Image 7a.
Slide the remaining boards into place, as shown in Image 8a. Now you get an trough planter box with 11.9” planting depth. Then, go to page 15, and follow the steps afterwards.
Note: If you want to add trellis kit onto this bed, please assemble the extension connectors before this step, to avoid disassembling the boards later.
If necessary, use your rubber mallet to ensure the boards are tightly in place. Cover the brackets with the 4 end caps, as shown in Image 10.
Then you get an Everbloom Deep Trough Planter Box, as shown in Image 11.
Sometimes there might be a misalignment of the Corner Posts as shown in Image 12 and Image 13, which may result in difficulty of sliding boards into the brackets. Please adjust them to the right position so that they are parallel to each other, and perpendicular to the ground.

Bloom On.

Everbloom- Garden.com
US Patent Pending
Subscribe at www.everbloom-garden.com for extra savings and upgrading information!
Distributed by:
Dynaforge Trading LLC
St. Paul, MN55101
Email:service@everbloom-garden.com

Parts include

2″ Swivel Caster Wheel . ………………………………. x 4
Stainless Steel Bolt ….. ………………………………… x 4
Stainless Steel Nylon Lock Nut ………………………. x 4
5mm hex key .. ………………………………………….. x l
13mm nut driver ……………………………………………. x l

Installation l

Install on Everbloom
E281719 Elevated Planter Box
E283612 Elevated Trough Planter Box
Before installing the wheels, carefully flip over the garden bed so that it lays flat with the long side facing toward the sky.

Insert the wheel
- Pay attention to the direction of the wheel and the corner post.
Insert the bolt, Be sure it goes bracket inside the post through the support
Turn on the nylon lock nut and tighten them with a hex key and nut driver
Install the lower wheel
Assemble the remaining wheels using the same method. Attn: The direction of each wheel aligns with the corner posts.
After installing all wheels, carefully flip over the Planter Box. Then, you get a mobile planter box.

Installation 2

Install on Everbloom
E213612 Deep Trough Planter Box I
E211719 Corner Stone Planter Box I
E144519 Deskside Planter Box I
E143612 Trough Planter
Before installing the wheels, carefully flip over the garden bed so that it lays flat with the long side [ or short side of post) pointing towards the sky.

Remove bolts and nuts on the post bracket with hex key and nut driver and take out one support bracket, as shown in Pie. la and Pie. l b.
- Note:
- Please pay attention to the position of the support bracket that need to be taken out.
Insert the wheel
Insert the bolt
Turn on the nylon lock nut and fasten it
Insert another bolt in the pack from side to side.
- Turn on the nut and fasten it.
- Be sure it goes through the support brack inside the post.
Take off the bolts and nuts on post brackets on the other side, and insert the wheel. Fix it with bolts and nuts.
Flip over the garden bed, then install another two wheels following the steps above.
Flip over the bed again so it stands upright