Everbloom E213612G Deep Trough Planter Box Installation Guide
- June 10, 2024
- Everbloom
Table of Contents
Everbloom E213612G Deep Trough Planter Box Installation Guide
Thank You!
You’re only a few steps away from your perfect vegetable garden or elevated planter. We hope you enjoy!
Before You Start
Please read the instructions carefully to familiarize yourself with every detail and step involved. Keep this manual for future reference. Find a suitable space to assemble your new Trough Planter Box.
You need at least 37” x 13” (94 x 33cm) for the finished product. A flat and firm area (like a garage floor or flat yard space) is perfect! The only tool you may need is a rubber mallet.
Important Notes
Small parts are included; we advise you to keep them away from children and
pets.
We also suggest having another person help you assemble. Maximum Load
Capacity: approximately 4 cu. ft. of soil
- Subscribe at www.everbloom-garden.com for extra savings and upgrading information!
Questions or Comments?
Email us at service@everbloom-garden.com
Parts List
Deep Trough Planter Box – 36″ L x 12″ W x 21″ H
Assembly
Deep Trough Planter Box – 36″ L x 12″ W x 21″ H
Eleven depths are available by changing the sequence of the boards and position of the bottom boards, as shown in below images. You can choose according to different needs first.
- For depth of 2.5”, 5”, 7.25”, 9.5“, 9.75”, 12”, 14.4” and 17” as shown in Image 1, 2, 3 and 4, please refer to steps from page 4.
- For depth of 4.75”, 7” and 11.9” as shown in Image 2, 3 and Image 4, please refer to steps from page 10.
For the deeper planting depths of 17”, please follow steps below.
For other depths, the assembly methods are similar, just pay attention to the
sequence of the boards and position of the bottom boards, please refer to page
3.
Start by making sure each corner post is oriented correctly, as shown in Image
3. Slide one short board A into the corner brackets from above.
Note: The short boards need to be placed in the inward “U” shape of the
brackets, as shown in Image 4.
Slide another short board A into the other two corner brackets from above, as shown in Image 5.
With the help of another person holding the 2 assembled parts, slide the 2 long support boards into the brackets from above. Make sure that one support board goes straight to the bottom, while the other one stays in the middle of the way (don’t push it to the bottom), with the top edge between the 4th and 5th holes of the post.
Put the bottom boards on the lower slot of long support boards. Make sure the 2 ends of these bottom boards go into the slot and rest in them with enough contact as shown in Image 7. Adjust the height of the higher long support board slightly to hold these bottom boards if necessary.
Push down the higher long support board to the bottom, as shown in Image 8.
Slide the remaining boards into place, as shown in Image 9. Now you get an
trough planter box with 17” planting depth. Then, go to page 15, and follow
the steps afterwards.
Note: If you want to add trellis kit onto this bed, please assemble the
extension connectors before this step, to avoid disassembling the boards
later.
For the planting depth of 11.9”, please follow steps below.
For depth of 4.75” or 7”, the assembly methods are similar, just pay
attention to the sequence of the boards and position of the bottom boards,
please refer to page 3.
Start by making sure each corner post is oriented correctly, as shown in Image
3a. Slide one short board B into the corner brackets from above.
Note: The short boards need to be placed in the inward “U” shape of the
brackets, as shown in Image 4a.
Slide another short board A into the other two corner brackets from above, as shown in Image 5a.
With the help of another person holding the 2 assembled parts, slide the 2 long support boards into the brackets from above to the bottom, as shown in Image 6a.
Put the bottom boards on the long support boards, as shown in Image 7a.
Slide the remaining boards into place, as shown in Image 8a. Now you get an trough planter box with 11.9” planting depth. Then, go to page 15, and follow the steps afterwards.
Note : If you want to add trellis kit onto this bed, please assemble the extension connectors before this step, to avoid disassembling the boards later.
If necessary, use your rubber mallet to ensure the boards are tightly in place. Cover the brackets with the 4 end caps, as shown in Image 10.
Then you get an Everbloom Deep Trough Planter Box, as shown in Image 11.
Note
Deep Trough Planter Box – 36″ L x 12″ W x 21″ H
Sometimes there might be a misalignment of the Corner Posts as shown in Image 12 and Image 13, which may result in difficulty of sliding boards into the brackets. Please adjust them to the right position so that they are parallel to each other, and perpendicular to the ground.
Everbloom-Garden.com
US Patent Pending
Subscribe at www.everbloom-garden.com for
extra savings and upgrading information!
References
- Raised Garden Bed Kits | Elevated Planters – EverBloom Garden
- Raised Garden Bed Kits | Elevated Planters – EverBloom Garden
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>