Everbloom S333618W/B/G Self Watering Mobile Elevated Garden Installation Guide
- June 9, 2024
- Everbloom
Table of Contents
Everbloom S333618W/B/G Self Watering Mobile Elevated Garden
Self-Watering Mobile Elevated Garden
Installation Guide
Model# S333618W: brown
Model# S333618WB: blue
Model# S333618WG: grey
Thank You!
You’re only a few steps away from your perfect vegetable garden or elevated
planter. We hope you enjoy!
Before You Start
Please read the instructions carefully to familiarize yourself with every detail and step involved. Keep this manual for future reference. Find a suitable space to assemble your new Elevated Garden Bed.
You need at least 37” x 19” (94 x 49 cm) for the finished product. A flat and firm area (like a garage floor or flat yard space) is perfect! The only tools you may need are a rubber mallet and a scissor.
Important Notes
Small parts are included; we advise you to keep them away from children and
pets.
We also suggest having another person help you assemble. Maximum Load
capacity: approximately 3.2 cu. ft. of soil
Subscribe at www.everbloom-garden.com for extra savings and upgrading information!
Model# S333618W/B/G
Dimensions 36″ L x 18″ W x 36″ H
Parts List 1
Self-Watering Mobile Elevated Garden – 36″ L x 18″ W x 36″ H
Self-Watering Mobile Elevated Garden – 36″ L x 18″ W x 36″ H
Assembly
Self-Watering Mobile Elevated Garden – 36″ L x 18″ W x 36″ H
Two depths are available by changing the position of reservoir, as shown in Image 1. You can choose according to different needs first.
For planting depths of 7.25”, please follow steps below.
For planting depths of 9.75”, the assembly method is similar, just pay
attention to the position of reservoir, please refer to page 4.
Start by making sure each corner post is oriented correctly, as shown in Image 2. Slide one short board A into the corner brackets from above.
Note: The short boards need to be placed in the inward “U” shape of the brackets, as shown in Image 3.
Slide another short board A into the other two corner brackets from above, as shown in Image 4.
With the help of another person holding the 2 assembled parts, slide the 2 long supporting boards into the brackets from above. Make sure that one support board goes straight to the bottom, while the other one stays in the middle of the way (don’t push to the bottom), with the top edge between the 1st and 2nd holes of the post, as shown in Image 5.
Take off the 4 end caps from reservoir bottom trays, as shown in Image 6. Flip over the bottom trays, and connect them with black silicone connecting tube tightly, as shown in Image 7.
Flip over the connected bottom trays and put them on lower slots of long support boards. Make sure the 2 ends of these bottom trays go into the lower slots and rest in them with enough contact as shown in Image 8. Adjust the height of the higher long support board slightly to hold these bottom boards if necessary.
Punch down the perforated round pannel on the top covers on both sides, as
shown in Image 9. Then, put the top covers on the bottom trays, as shown in
Image 10.
Note: Use a utility knife to cut off the perforated round pannel if it’s
hard to punch down.
Push down the higher long support board to the bottom, as shown in Image 11.
Slide the remaining boards into place, as shown in Image 12.
Note: If you want to add trellis kit onto this bed, please assemble the
extension connectors before this step,to avoid disassembling the boards later.
Carefully flip over the planter so that it lays flat with the long support boards pointing towards the sky. Insert caster wheels into corner brackets, as shown in Image 13and Image 14.
Fix the wheels with bollts and nuts, as shown in Image 15.
Fasten bolts and nuts with nut driver and hex key which are included in pack , as shown in Image 16.
Flip over the planter again so it stands upright, as shown in Image 17.
Seal the small gaps between reservoirs and the gaps between reservoir and short boards with black tape,as shown in Image 18.
Insert two fill tubes to the bottom through the holes near corners, as shown in Image 19. Please pay attention to the direction of the fill tube, make sure the ends with small holes go into the reservoir.
Insert water level indicator into the cap, as shown in Image 20. Then, put them into the fill tube, as shown in Image 21. Put the fill tube lid onto another fill tube. When you fill water, just remove the lid. Please do not misplace the lid after watering.
Note: Please keep the replacement parts in safe place. You may need them in the future.
If necessary, use your rubber mallet to ensure the boards are tightly in place. Cover the brackets with the 4 end caps, as shown in Image 22.
Now you get an EverBloom Self-Watering Mobile Elevated Garden with desired planting depth, as shown in Image 23. Then, enjoy your gardening time!
Sometimes there might be a misalignment of the Corner Posts as shown in Image 24 and Image 25, which may result in difficulty of sliding boards into the brackets. Please adjust them to the right position so that they are parallel to each other, and perpendicular to the ground.
Bloom On.
Everbloom-Garden.com
US Patent Pending
Subscribe at www.everbloom-garden.com for
extra savings and upgrading information!
Distributed by:
Dynaforge Trading LLC
St. Paul, MN55101
Email: service@everbloom-garden.com
References
- Raised Garden Bed Kits | Elevated Planters – EverBloom Garden
- Raised Garden Bed Kits | Elevated Planters – EverBloom Garden
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>