Fingers WL2 Wireless Barcode Scanner User Guide

Quick Start Guide
Quick Scan WL2 Wireless Barcode Scanner

Important – Warnings and Safety Instructions

1. Do not place the Barcode Scanners near the heat sources such as fire, radiators, stoves, light candles and other apparatus that produces heat.
2. Use only those accessories supplied by Fingers.
3. It is recommended to refer all servicing to qualified personnel. Servicing is required when the Barcode Scanner has been damaged in any way. Any evidence of any attempt to open and/or alter the device, including any scratch, peeling, puncturing, or removal of any of the labels, will void the Limited Warranty.

In the box

1 x Quick Scan WL2 Barcode Reader
1 x USB Receiver
2 x USB Charging Cable
1 x Stand
1 x Quick Start Guide

Care and Maintenance

1. Unplug the Barcode Scanner before cleaning it.
2. Use soft, damp cloth to clean the surface.
3. Do not use any chemicals, solvents, or cleaning solutions containing alcohol, ammonia or abrasives.
4. Do not allow any liquid to enter into any of the openings.

Connecting the Scanner

Reading Techniques

1. The viewfinder projects an aiming beam that should be centered over the barcode. However, it can be tilted at any angle and in any direction for an effective read.
2. Hand hold the scanner over the barcode, pull the trigger and position the aiming beam on the barcode.
3. The aiming beam is smaller when scanner is placed closer to the barcode and larger when it is farther from the code.
4. Hold the scanner close to the smaller barcodes, and farther away from bigger barcodes to get a good read.
5. If the barcode is highly reflective (ex. Laminated sheets, glossy), you might be required to position the scanner at an angle in such a way the barcode can be read and scanned clearly.

Note:
i. If the scanner beeps once, the link has been established.
ii. The scanner will turn off in 20 seconds with a long, when in idle mode.
iii. To use it again, press the button and two beeps will be heard.
All the parameter settings of the scanner cab be finished by scanning the barcodes and saving them in the storage. Even while being switched off, these setting do work.

Standard Product Defaults

The following barcode resets all standard product default settings.

Scanner Pairing with Receiver

1. Scan “Factory Default” barcode
2. Pull and Plug the receiver into the PC
3. When the indicator on receiver starts flashing in blue to scan “Forced Pairing”, it will clear the Previous pairing and finish the current pairing. After pairing is successful, two beeps of sound will be heard.

Note: After successful pairing, the indicator of DATA on receiver will flash in blue (about 1 time/sec), open a text to scan required barcode. In this case, the light flashes in blue and data can be seen in the text.

| Quit Inventory Mode
---|---
Upload all data and cleared
(Note: Upload all data stored and clear them)
Upload all data and no cleared
(Note: Upload all data stored but do not clear them)
Upload one data and cleared
(Note: Upload one data stored and clear it)
Upload one data and no cleared
(Note: Upload one data stored but do not clear it)
Display the number of barcode to be uploaded
Clear

Scen Mode

Buzzer

Keyborad Language

Keyborad caps Lock Control

Sufiix Setting Shock setting

Sembologies Selection

Product Specifications

General| Type:
Interface:
In-built Memory: Indicators:
Operation Mode: Barcode Type Support:| Wireless
USB Receiver
1 MB
Vibration, Beeper, LED Trigger
All Standard 1D Barcodes
---|---|---
Connection| Frequency:
Effective Range:| 2.4GHz
Up to 100 meter (Open Space)
Optical| Light Source:
Scan Rate:
Resolution:
Print Contrast Ratio: Depth of Field:| 650 nm visible laser diode a 300 scans/sec
4 mil
a 15%
0-250 mm (0.33mm, PCS 90%)
Electrical| Input Voltage:
Working Current: Standby Current: Sleep Mode:| DC 5 V ± 10% 85 mA
150 mA
150 uA
Battery| Battery Type:
Battery Capacity: Charging Type: Charging Time:| Lithium
2200 mAh
Mini USB cable About 6 hours
Physical| Housing Material: Charging Cable Type: Dimensions:
Weight:
Colour:| ABS+PC
Mini USB (About 1 meter) 15.4 (H) x 8.5 (W) x 6.2 (L) cm 187 grams (without receiver) Black + Grey
Environment & Safety
Conformance| Operating Temperature: Storage Temperature: Operating Humidity:
Shock Resistance:| 0°C — 40°C
40°C — 70°C
5% — 85% (Non-condensing) 1.5 m drops

fingers.co.in Ver:1 02

• Images shown may ‘ary from actual product. Specifications, features and appearance are subject to
  change without notice.

• All logos, brands, trademarks and product names are properties of their respective owners.

• Product war anty is governed by warranty terms mentioned on www.fingers.co.in

• This product falls under e-waste (Management & Handling) Rules, 2011. For proper disposal method, visit our website www.fingers.co.in

Documents / Resources

| Fingers WL2 Wireless Barcode Scanner [pdf] User Guide
WL2, WL2 Wireless Barcode Scanner, Wireless Barcode Scanner, Barcode Scanner, Scanner
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>