JLL JF100 Monitor Instruction Manual
- June 9, 2024
- JLL
Table of Contents
JLL JF100 Monitor
Product Information
JF100 Monitor
- The JF100 Monitor is a fitness monitor produced by JLL Fitness Ltd.
- The monitor has been tested and conforms with relevant EU directives regarding health and safety or environmental protection.
- The monitor has a total of 6 readouts, displaying time, speed, distance, heart rate, calories, and odometer.
- The monitor has a scan mode which allows the user to have an overview while training without pressing any buttons.
- The monitor requires batteries for operation.
Product Usage Instructions
Safety Precautions
- Do not use or reproduce the manual in parts or entirety without the authorization of JLL Fitness Ltd.
- Take care when cleaning the monitor as the LCD screen can easily be scratched. Use a soft dry cloth and do not spray cleaning chemicals or apply water directly onto the monitor as it may damage the internal components.
Installation
- Insert the batteries, making sure they are the correct way round.
- Connect the male-to-female wires from the base to the monitor.
- Slot the monitor to the frame.
Operation
- When first powered on, the monitor will automatically be in `Scan’ mode. This means the digits in the largest segment on the screen will change every few seconds between time, distance, speed etc.
- To exit scan mode, press `MODE’ and continuously press it to view each readout. If you are within scan mode, there will be a scan icon in the bottom left to indicate this.
- To set target programs, press and hold `MODE’ until the digits begin to change.
- To reset the monitor, press and hold `RESET’ until all the digits come up and return to zero.
Data Readouts
| Readout | Measurement |
|---|---|
| Time | Minutes: Seconds |
| Speed | KM/H |
| Distance | Kilometers |
| Heart Rate | PPM (Pulsations Per Minute) |
| Calories | N/A |
| Odometer | Kilometers |
Troubleshoot
| Issue | Resolutions |
|---|---|
| No power to the monitor | Check batteries and connections. |
| No pulse reading | Ensure heart rate monitor is correctly attached and |
positioned.
Readings not changing| Reset the monitor or contact JLL Fitness Ltd for
further
assistance.
Contact Details
- Tel: 0121 328 7507
- Email: info@jllfitness.co.uk
- Live Chat: WWW.JLLFITNESS.CO.UK
SAFETY PRECAUTIONS
The monitor on this machine has been tested to the required standards, and each of those passed regulations are shown via the following symbols: WEEE – Waste Electrical and Electronic Equipment Recycling. ABS – Acrylonitrile Butadiene Styrene often referred to as ABS is a type of plastic that is an opaque thermoplastic. CE – The product conforms with relevant EU directives regarding health and safety or environmental protection. QC Pass – A product that has fulfilled the requirements of technical control and passed the outgoing exams. ROHS – This is an abbreviation for “Restriction of (the use of certain) Hazardous Substances in electrical and electronic Equipment”.
CLEANING
Please take care when cleaning this monitor as the LCD screen can easily be scratched.
- You will need a soft dry cloth
- Do not spray cleaning chemicals directly onto the monitor
- Do not apply water to the monitor as it is electrical and may damage the internal components
INSTALLATION
STEP 1
Insert the batteries, making sure they are the correct way around.
STEP 2
Connect the male-to-female wires from the base to the monitor.
STEP 3
Slot the monitor to the frame.
OPERATION
The JF100 monitor has a total of 6 readouts, displaying:
Time Speed Distance Heart Rate Calories Odometer
When first powered on, the monitor will automatically be in ‘Scan’ mode. This
means the digits in the largest segment on the screen will change every few
seconds between time, distance, speed etc. This will allow you to have an
overview while training without pressing any buttons.
EXITING SCAN MODE
Press ‘MODE’ to exit scan mode and continuously press it to view each readout.
If you are within scan mode, there will be a scan icon in the bottom left to
indicate this.
SETTING TARGET PROGRAMS
On this monitor, you are able to set a target time, distance, pulse and
calories.
- Start by pressing ‘MODE’ until your chosen setting flashes.
- Then press ‘SET’ to change the digits to your desired target.
- Once set, begin your workout by pedaling and you will see the digits begin to change.
RESETTING YOUR MONITOR
Press and hold the ‘RESET’ button until all the digits come up and return to zero,
DATA READOUTS
Readout Measurement
- Time: Minutes: Seconds
- Speed: KM/H
- Distance: Kilometres
- Pulse: PPM (Pulsations Per Minute)
- Odometer: Kilometres
TROUBLESHOOT
CONTACT DETAILS
- Tel: 0121 328 7507
- Email: info@jllfitness.co.uk
- Live Chat: WWW.JLLFITNESS.CO.UK
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>