MONOGRAM UDT165SIVII 18 Inch Top Control Integrated Dishwasher Instruction Manual

MONOGRAM UDT165SIVII 18 Inch Top Control Integrated Dishwasher

Product Information:

This product is an 18 Top Control Integrated Dishwasher. It comes with a custom panel template and instructions for installation. The custom panel should be sized according to the installation situation, with a panel height of 26-13/16 (68.1 cm) and a minimum gap of 1/2 (1.27 cm) for clearance.
The custom panel should not weigh more than 8 lbs to ensure optimum door balance performance. The package includes brackets, screws, spacer pads, metal spacers, and Phillips flat-head screws in various sizes.

Product Usage Instructions:

1. Step 1: Custom Panel Size Requirements

   • HEIGHT
     Panel height should be 26-13/16″ (68.1 cm).
     The top of the custom panel must be flush with the top of the door. The 1/2″ (1.27 cm) minimum gap between the top of the door and the bottom of the countertop must be maintained.

   • WIDTH
     Panel width must be 17-1/2″ (44.4 cm).
     If the panel width is less than 17-1/2″ (44.4 cm), it will not cover the dishwasher frame.

2. Step 2: Draw Centerline

   • Place the custom panel on a flat surface with the appearance side down.
   • Locate the vertical center of the panel at the top.
   • Use a carpenter’s square to draw a centerline from top to bottom.

3. Step 3: Align Template to Panel

   • Trim template on the dotted line along all sides.

   • Place the template on the panel aligned with the top edge and the centerline. Use tape to hold in place.
     IMPORTANT: If the template is not aligned with the top edge of the panel, the 1/2″ (1.27 cm) minimum gap will not be maintained. This 1/2″ (1.27 cm) minimum gap must be maintained to prevent condensation and damage to the control panel from screw heads.

   • Use an awl to mark the screw hole locations indicated on the template. Remove the template.

4. Step 4: Install Mounting Screws and Spacers
   Note: The custom panel is secured to the dishwasher door with the metal spacers, screws and brackets provided. The metal spacers and brackets will slip into the slots
   on the dishwasher door and control panel.
   

   • Align the metal spacers over the top pilot holes. Ensure the thick, recessed side is facing up.
   • Drive the supplied 1″ (2.54 cm) Phillips flat-head screws through the metal spacers and into the panel.
   • Align the brackets over the bottom pilot holes. Ensure the curved lip is facing up. If the surface of the panel is not flat, use the spacer pads provided.
   • Drive the 5/8″ (1.58 cm) Phillips flat-head screws through the brackets and into the panel.

5. Step 5: Install Custom Handle
   A custom handle must be installed onto the panel before the panel is secured to the dishwasher door.

   • The handle should be installed so that it aligns with adjacent drawer handles, or 4-1/2″ (115 mm) max. from the top of the panel. Secure the handle in the same manner as the cabinet handles. Screws must be countersunk into the panel.

6. Step 6: Install Assembled Panel

   • Secure the panel to the door by inserting the top metal spacers and bottom brackets into the matching slots on the dishwasher door and control panel.
   • Make sure both metal spacers and both brackets engage the slots.
   • Press the panel against the door and push downward until the metal spacers and brackets are fully engaged into the slots. The panel should align evenly with the top and sides.
   • Stand the dishwasher upright.
   • Open the dishwasher door and remove the first side screw from the top on each side of the inner door.
   • Replace these screws with the 1-1/2” (3.81 cm) Phillips flat-headed screws and drive them through the inner door and into the custom panel. IMPORTANT: Do not overtighten screws. Excessive tightening of the screws could damage door edges.

7. Step 7: Check Door Balance
   To check the door balance, hold the top of the dishwasher firmly.
   

   • Check the door balance by opening and closing the door.
   • If the door drops when released, increase the spring tension. If the door rises when released, decrease the spring tension.
   • Using a T25 torque driver or socket wrench (as appropriate), adjust in the direction shown. Adjust both sides equally.

Note: The provided parts include metal spacers, brackets, spacer pads (optional), Phillips flat-head screws in various sizes.
IMPORTANT
A custom handle must be installed onto the custom panel. Install the custom handle 4-1/2″ max. from the top of the panel.

PARTS INCLUDED:

• (2) Brackets
• (4) 5/8″ (1.58 cm) Phillips flat-head screws
• (2) Spacer pads
• (2) Metal spacers
• (2) 1″ (2.54) Phillips flat-head screws
• (2) 1-1/2″ (3.81 cm) Phillips flat-head screws

Dimensions

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>