OVERSTEEL AZURITE RGB Gaming PC Case User Manual
- June 9, 2024
- OVERSTEEL
Table of Contents
- TECHNICAL SPECIFICATIONS
- PC CASE GENERAL DIAGRAM
- FRONT PANEL I/O AND MOTHERBOARD CONNECTORS
- ACCESORY BAG
- BASIC INSTALLATION
- Disassemble the side panel and the front panel
- Install the power supply
- Install the motherboard
- Install GPU and expansion slot (PCI)
- RGB Fandub Controller installation
- Install fan and radiator (optional)
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
OVERSTEEL AZURITE RGB Gaming PC Case
TECHNICAL SPECIFICATIONS
MODEL | AZURITE |
---|---|
DIMENSIONS (L x W x H) | 340mm x 200mm x 449mm |
MATERIAL | Steel 0,5mm SPCC, tempered glass |
FANS LOCATION | Front: 3x 120mm 3x 140mm (3x A-RGB included) Rear: 1x 120mm (1x |
A-RGB included) Top: 2x 120mm 2x 140mm
WATER COOLING| Front: up to 360mm radiator Top: up to 240mm radiator Rear: up
to 120mm radiator
DRIVE BAYS| 4x 2,5″ + 2x 3,5″/2,5″
EXPANSION SLOTS| x7 + 2
FRONT I/O| USB 3.0 x1 USB 2.0 x2 Headphone/Microfone x1 Power Reset/LED
DUST FILTER| 1x Top 1x Bottom
MOTHERBOARD| TYPE ATX, MicroATX, ITX
POWER SUPPLY| ATX up to 180mm (not included) bottom position
VGA (GPU)| Up to 340mm (not included)
CPU COOLER| Up to 174mm (not included)
PC CASE GENERAL DIAGRAM
- Magnetic dust filter
- Side tempered glass
- Back metal side
- 120mm RGB fan
- PSU enclosure bay
- HDD/SSD Enclosure Bay
- Front panel I/O
- PCI expansion bays
FRONT PANEL I/O AND MOTHERBOARD CONNECTORS
ACCESORY BAG
-
Motherboard standoffs
-
Motherboards /SSD Screws
-
PSU Screws
-
HDD Screws
-
Fan Screws
-
HDD Enclosure screws
-
Zip ties
BASIC INSTALLATION
A Disassemble the side panel and the front panel
B Install the power supply
C Install the motherboard
D Install HDD/SSD
E Install GPU and expansión slot (PCI)
F Install fan and radiator (optional)
G RGB Fanhub Controller installation
Disassemble the side panel and the front panel
![Disassemble the side panel
and the front panel](https://manuals.plus/wp-content/uploads/2023/04 /OVERSTEEL-AZURITE-RGB-Gaming-PC-Case-User-Manual-16.png)
Take out the screws before disassembling side panel Remove the side panels before disassembling the front panel
Special attention to the tempered glass side panel. Handle with care
![Disassemble the side panel
and the front panel](https://manuals.plus/wp-content/uploads/2023/04 /OVERSTEEL-AZURITE-RGB-Gaming-PC-Case-User-Manual-17.png)
Install the power supply
Make sure the screw holes for PSU and the PC case are alligned before screwing
Install the motherboard
Make sure that the motherboard aims at the copper cylinder and install the standoffs (No.1) before screwing in with the No.2 screws
Install GPU and expansion slot (PCI)
Remove the bafle marked in the picture, make sure the VGA card aims at the motherboard slot and then fix VGA card and case with No.3 screw
RGB Fandub Controller installation
Ⓐ FRONT Fans → 3x 120mm → 3x 140mm Radiator up to 360mm
Ⓑ TOP Fans → 2x 120mm →2x 140mm Radiator up to 240mm
Ⓒ REAR Fans → 1x 120mm Radiator up to 120mm
Install fan and radiator (optional)
5v 3pin A-RGB Connector
3/4pin power connector
4pin (PWM) connector and 5v 3pin A-RGB syncing for motherboard
SATA connector to PSU power
Controller has 4pin power outputs(PWM), but its also compatible with 3pin. Connect it skipping the first starting from left side
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>