OVERSTEEL 27VF16K 27 Inch Krypto Curved PC Gaming Monitor User Manual
- June 9, 2024
- OVERSTEEL
Table of Contents
- 27VF16K 27 Inch Krypto Curved PC Gaming Monitor
- Important Safety Precautions
- **** Power & Electrical Warnings
- Product Description
- Product Overview
- Stand Installation
- Wall Mounting
- Basic Operation
- OSD Menu
- LED Effects and Gameplus
- Technical Specifications of Product
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
27 FULL HD RESOLUTION
1920 x1080@165Hz
27VF16K 27 Inch
Krypto Curved PC Gaming Monitor
User Manual
27VF16K 27 Inch Krypto Curved PC Gaming Monitor
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc, in the United States and other countries.
Important Safety Precautions
-
Please read all the instructions carefully before using this product.
-
BE SURE TO unplug the power cord when cleaning LCD. Never clean it with liquid detergent or spraying detergent, but wipe it with wet soft cloth. If it is still not clean, please use special detergent for LCD.
-
DO NOT use accessories not authorized by the manufacturer, other wise they may incur danger.
-
When disconnecting the power cord of display or power adapter, always remember to hold the plug instead of puling the wire to unplug the power cord.
-
Keep the display away from water sources such as bath tub, washbasin, sink or washing machine. DO NOT place the display on wet floor or near a swimming pool, or press LCD surface with fingers or hard objects.
-
The grooves and openings on the back and bottom of the shell are for ventilation purpose and also for guaranteeing the reliability of the elements and preventing them from overheating; in order to prevent the vents from blocking DO NOT place the display on bed, sofa, carpet or other similar surfaces; DO NOT place the display near to or on heat radiator or heater; DO NOT put the display into embedded device, unless it is provided with adequate ventilating equipment.
-
Only the type of power source indicated on the nameplate applies to this display. If you have any questions on the type of power source you use, please consult the dealer of the display or local administration of power supply.
-
For safety, the display or the power adapter is equipped with three-pin plug power cord. The third pin of this plug is for grounding, and only applicable to socket that is correctly grounded. In case that your socket is not available for the plug, please contact electrician to replace the socket
-
Since there is high voltage or other risks when the shell is opened or moved, please DO NOT repair the display by yourself, but request qualified maintenance staff to carry out.
-
In one of the following cases, please unplug the display or the power adapter and ask qualified maintenance staff for help:
a. The power cord or the plug is impaired or worn.
b. The display falls off or the shell is damaged.
c. The display is obviously abnormal. -
Please place the display in a cool, dry and well ventilated place.
-
Store the display in temperature range of -10°C-60°C, beyond which the display may be damaged permanently.
**** Power & Electrical Warnings
The monitor should be operated only from the type of power source indicated on
the label. If you are not sure of the type of power supplied to your home,
consult your dealer or local power company. The monitor is equipped with a
three-pronged grounded plug, a plug with a third (grounding) pin. This plug
will fit only into a grounded power outlet as a safety feature. If your outlet
does not accommodate the three-wire plug have an electrician install the
correct outlet, or use an adapter to ground the appliance safely. Do not
defeat the safety purpose of the grounded plug. Unplug the unit during a
lightning storm or when it will not be used for long periods of time. This
will protect the monitor from damage due to power surges.
Do not overload power strips and extension cords. Overloading can result in
fire or electric shock.
To ensure satisfactory operation, use the monitor only with UL listed
computers which have appropriate configured receptacles marked between
100-240V AC, Min. 5A.
The wall socket shall be installed near the equipment and shall be easily
accessible.
Read the safety instructions carefully and thoroughly.
All cautions and warnings on the device or user’s manual should be noted.
Refer servicing to qualified personnel only.
Keep the User’s Guide that comes with the package for future reference.
To prevent fire or shock hazard, keep this device away from humidity and high
temperature.
Lay this device on a reliable flat surface before setting it up.
Make sure that the power voltage is within its safety range and has been
adjusted properly to the value of 100-240V before connecting the device to the
power outlet. Do not disable the protective earth pin from the plug. The
device must be connected to an earthed mains socket-outlet Always disconnect
the power cord or switch the wall socket off if the devicewould be left unused
for a certain time to achieve zero energy consumption.
Place the power cord in a way that people are unlikely to step on it. Do not
place anything on the power cord.
The ventilator on the device is used for air convection and to prevent the
device from overheating. Do not cover the ventilator.
Do not leave the device in an unconditioned environment with a storage
temperature above 600C or below-200C, which may damage the device.
NOTE: The maximum operating temperature is around 400C.
When cleaning the device, be sure to remove the power plug. Use a piece of
soft cloth rather than industrial chemical to clean the device. Never pour any
liquid into the opening that could damage the device or cause electric shock.
Always keep strong magnetic or electrical objects away from the device.
If any of the following situations arises, get the device checked by service
personnel:
The power cord or plug is damaged.
Liquid has penetrated into the device.
The device has been exposed to moisture.
The device does not work well or you can not get it work according to user’s
manual.
The device has dropped and damaged.
The device has obvious sign of breakage
Warning!
Overuse of screens is likely to affect eyesight.
Recommendations:
- Take a 10-minute break for every 30 minutes of screen time.
- Children under 2 years of age should have no screen time. For children aged 2 years and over, screen time should be limited to less than one hour per day
IMPORTANT SAFETY PRECAUTIONS
Do not place the monitor in rain, humid environment or open the monitor case
to avoid any shock, electrical hazards, and/or mechanical hazards.
Operation
- Keep the monitor out of direct sunlight and away from stoves or any other heat source.
- Keep the monitor out of water source
- Remove any object that could fall into ventilation holes or prevent proper cooling of the monitor’s electronics.
- Do not block the ventilation holes.
- Do not knock or drop the monitor during operation or transportation.
Maintenance Guidelines
CAUTION
- Do not place the monitor in rain, humid environment or open the monitor case to avoid any shock, electrical hazards, and/or mechanical hazards.
- Before cleaning the monitor, unplug the monitor power cable from the electrical outlet.
Caring for Your Monitor
- To clean your screen, slightly dampen a soft, clean cloth with water.
- If possible, use a special screen-cleaning tissue or solution. Do not use benzene, thinner, ammonia, abrasive cleaners, or compressed air.
- Use a slightly dampened, warm cloth to clean the frame. Avoid using detergent of any kind as some detergents might leave a milky film on the plastics.
- Unplug the monitor if you are not going to use it for an extendedperiod of time.
- To avoid the risk of shock or permanent damage to the set, do not expose the monitor to dust, rain, water, or excessive moisture – environment. If your monitor gets wet wipe it with dry cloth as soon as possible.
Product Description
Packing list
Please check the following items in the packing case before installation: If
any of above items is missing, please contact with the dealer.
The screws come in different sizes: NO.1 (11mmx4pcs), NO.2 (35mmx4pcs).
Extra screws may be included as backup.
Product Overview
2.1 Monitor Buttons
1 | M Menu Button | Press to display the OSD menu or enter sub-menus. |
---|---|---|
2 | **** Down Button | Press to move down in the menus. |
3 | **** Up Button | Press to move up in the menus. |
4 | Exit Button | Press to exit. |
5 | Power Button | Press to turn the monitor on/off. |
6 | LED Indicator | Changes colors to indicate status. |
2.2 Monintor Ports
Connect the signal line to output interfaces signal of DP/HDMI signals of PC,
and then connect the other end of the signal line to the corresponding signal
input port of the display.
7| Audio Output| Insert one end of the audio cable into the computer’s audio
output to receive the audio signals from your monitor.
---|---|---
8| HDMI Connectors| Insert one end of the HDMI cable into the computer’s HDMI
output and connect the other end to the monitor’s HDMI port.
9| DP Connectors| Insert one end of the DP cable into the computer’s DP
output and connect the other end to the monitor’s DP port.
10| Power Connector| Insert the power cable to supply power to the monitor.
Stand Installation
Keep the foam underneath the monitor before attaching the stand.
-
Open the package and take out the stand stem and the stand base mount them with a screw.
-
Take out the back cover and use two screws to mount it to the stand.
-
Open the pacakge and take out the product with the foam still attached. Carefully place it on a desk or table and shield the screen.
Let the stand snap into the back of the monitor
-
If you need to take off the stand, you can pull up the quick-relea button on the back cover.
Wall Mounting
This monitor only includes screws which may be used when attaching the monitor to a VESA 75*75mm type mount. No VESA mount o r mounting accessory is included.
-
Open the package, take out the product with foam still attached, and gently place it on a desktop or table. Remove the extra parts and the foam covering the back of the monitor. Pree the release buttontore move the stand plate.If the monitor was already attached to the stand, remove the stand.cv
-
Remove the original screws x4 (1) from the opening in the back of the monitor.
-
Follow the directions received with your mount, stand, or accessory and install the monitor on the wall or fixture as desired. Remember to use the included 4 screws when mounting the monitor. Refer to the image (2) for correct screw placement.
-
Do not discard the original screws. These may be needed for future use.
Basic Operation
- Insert one end of the DP cable into your PC’s graphics card, A HDMI cable may also be used. A HDMI cables is not included.
- Connect the other end of the cable to the corresponding connector on your monitor.
- Connect the power cableto your monitor then connect the other end to your power source. It is recommended that you use a surge protector with adequate voltage if a wall outlet cannot be hed directly.
- Locate the power button on the monitor and press it to turn the monitor on,
Adaptive-Sync
This feature is off by default. To activate, you must have hardware with
Adaptive-Sync capability, a DP or HDMI cable, and the latest graphic driver.
After connecting your computer and monitor witha DP or HDMI cable, you may
receive a prompt to enable the feature on your computer. If you do not, you
may need to enable the function in your graphics card menu. See your graphics
card manufacturer’s documentation for instructions.
This feature is off by default. To activate, you must have hardware with
Adaptive-Sync capability, a DP or HDMI cable, and the latest graphic drivers .
After connecting your computer and monitor with a DP or HDMI cable, you may
receive a prompt to enable the feature on your computer. If you do not, you
may need to enable the function in your graphics card menu. See your graphics
card manufacturer’sdocumentation for instructions.
Indicator Light
Solid blue light indicates power is on and the monitor is operating normally. Flashing blue light indicates no video source, no horizontal or vertical signal has been detected or voltage is low. Please ensure your computer is on and all video cables are fully inserted and/or connected.
OSD Menu
The On-Screen Display (OSD) Menu may be used to adjust your monitor’s settings
and appears on screen after turning on the monitor and pressing the M ( )
button.
When using the monitor for the first time, settings will automatically adjust
to optimal settings according to your computer’s standard configuration
settings.
-
Press one of the buttons (M, , , E, ****) to activate the navigation window.
-
Press M to enter the OSD screen.
-
Press or to browse functions.
– Highlight the desired function, then press M ( ) to enter the sub-menu.
– Press Wor Ato browse the sub-menus, and press M ( ) to highlight the desired function.
– Press W or Ato highlight the option, then press M ( ) to confirm the settings and exit the current screen. -
Press E to exit the current screen.
OSD Menu Functions
Main Menu | Sub-Menu | Options | Description |
---|---|---|---|
Brightness | Brightness | 0-100 | Adjust display brightness |
Contrast | 0-100 | Adjust display contrast | |
ECO | RTS, Standard, Game, RTS FPS, Movie, Text | Set visual mode | |
DCR | On/off | Turn on/off DCR function | |
Image | H. Position | 0-100 | Adjust horizontal position of the picture of |
source.
V. Position| 0-100| Adjust vertical position of the picture of source.
Clock| 0-100| Adjust picture phase to reduce the level of noise
Phase| 0-100| Adjust picture phase to reduce the level of noise
Aspect| Wide, Auto, 4:3| Set aspect ratio
Color Temp.| Color temp.| Warm, User, Cool| Adjust color temperature
Red| 0-100| Customize RGB components
Green| 0-100
Blue| 0-100
OSD Setting| Language| English| Set OSD Language
OSD H. POS.| 0-100| Adjust the OSD’s horizontal position
OSD V. POS.| 0-100| Adjust the OSD’s vertical position
Timer| 5-60| Set how long the OSD remains open after nonuse use
Transparency| 0-100| Set how long the OSD overall transparency
Reset| Image auto adjust| |
Color auto adjust| |
Reset| N/A| Reset monitor configurations
MPRT| On, Off| Turn MPRT on/off
MISC| Signal source| DP, HDMI1, HDMI2| Display the input signal
Volume| 0-100| Adjust audio volume
Low blue ray| 0-100| Set blue light filtering level
Over Driver| High, Middle, Low, Off| Set the Overdriver function
Led Effect| OFF, Normal, Flicker| Reset monitor configurations
Adaptive-Sync| On, Off| Turn on/off Adaptive-Sync
LED Effects and Gameplus
-
Press any one of the buttons (M, , , E, ( ****) to activate the navigation window.
-
Press ****( ) to switch Gameplus modes. Depending on your needs in-game, choose the corresponding game icon. These game icons are primarily designed to optimize your aim during shooting games, though they can be used for other scenarios.
-
Press ****( ) to switch LED rear display modes or turn off the LED effects.
Technical Specifications of Product
Model | NAT-OV-KR27VF16 / NAT-OV-KR27VF16K |
---|---|
Screen Size | 27″ |
Aspect Rstio | 16:09 |
Backlight | E-LED |
Brightness | 250cd/m² |
Panel | VA |
Resolution | DP1.2: 19201080@ 165Hz, HDMI 1.4: 19201080@120Hz |
Refresh Rate | 165Hz |
Response Time | 1Ms MPRT |
Viewing Angle | 178°(H)*/ 178°(V)° |
Contrast Ratio | 3000:1 |
VESA Mounting | 75*75mm |
Colours | 16.7M |
Adaptive-Sync | Yes |
Signal Input | HDMI 1.4*2, DP 1.21 |
Power Input | DC 12V **** 3.0 A |
Audio
Speakers| NO
Audio Out| Yes
Accessories
Power Cable| No
Power Adaptor| Yes
HDMI Cable| No
DP Cable| Yes
Additional Functions
Low Blue Light| Yes
Physical Dimensions
Dimensions (w/ Stand)| 616.2453.1195.7mm
Dimensions (w/o Stand)| 616.2367.296.3mm
Net Weight| 4.85Kg
Gross Weight| 6.72Kg
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>