SUNELL SN-IPR51xxBH Turret Network Camera User Guide
- June 9, 2024
- SUNELL
Table of Contents
SUNELL SN-IPR51xxBH Turret Network Camera
Product Information
The Easy Series Network Camera is a surveillance camera designed to monitor and record video footage in public places. It comes with a quick setup guide, which contains important information and precautions that users must follow to ensure proper use and prevent damage to the device. The camera is equipped with an image sensor, and it requires a power adapter to operate.
Product Precautions
Before using the Easy Series Network Camera, it is essential to fully understand the precautions outlined in the quick setup guide. Failure to observe these rules may cause injuries, device damage, or data loss. Users should take note of the following precautions:
Warnings
- Strictly observe installation requirements to avoid device damage.
- Conform to local electrical safety standards and use power adapters that are marked with the LPS standard.
- Use accessories delivered with this device.
- Ground the device if installed in places with unsteady voltage.
- Avoid exposing the device to water or any liquid.
- Avoid focusing strong light on the device.
- Ground the device if installed in places where thunder and lightning frequently occur.
Cautions
- Avoid heavy loads, intensive shakes, and soaking during transportation and storage.
- Protect the device from fall-down and intensive strikes, keep it away from magnetic field interference, and do not install it in places with shaking surfaces or under shocks.
- Clean the device with a soft dry cloth or slight neutral cleanser. Do not jam the ventilation opening.
- Keep the device away from heat sources and places with strong electric radiation.
- Take insect- and moisture-proof measures if the device is installed outdoors.
Product Usage Instructions
To use the Easy Series Network Camera, follow these instructions:
- Read the quick setup guide thoroughly before installing the device.
- Install the device according to the installation requirements outlined in the guide.
- Conform to local electrical safety standards and use power adapters that are marked with the LPS standard.
- Use accessories delivered with this device.
- Ground the device if installed in places with unsteady voltage.
- Avoid exposing the device to water or any liquid. If water or liquid unexpectedly flows into the device, immediately power off the device and disconnect all cables (such as power cables and network cables) from this device.
- Do not focus strong light on the device.
- Ground the device if installed in places where thunder and lightning frequently occur.
- Avoid heavy loads, intensive shakes, and soaking during transportation and storage.
- Protect the device from fall-down and intensive strikes, keep it away from magnetic field interference, and do not install it in places with shaking surfaces or under shocks.
- Clean the device with a soft dry cloth or slight neutral cleanser. Do not jam the ventilation opening.
- Keep the device away from heat sources and places with strong electric radiation.
- Take insect- and moisture-proof measures if the device is installed outdoors.
Precautions
Fully understand this document before using this device, and strictly observe rules in this document when using this device. If you install this device in public places, provide the tip “You have entered the area of electronic surveillance” in an eye-catching place. Failure to correctly use electrical products may cause fire and severe injuries.
WARNING| It alerts you to moderate dangers which, if not avoided, may
cause minor or moderate injuries.
---|---
CAUTION
| It alerts you to risks. Neglect of these risks may cause device damage,
data loss, device performance deterioration, or unpredictable results.
NOTE| It provides additional information.
WARNING
- Strictly observe installation requirements when installing the device. The manufacturer shall not be held responsible for device damage caused by users’ non-conformance to these requirements.
- Strictly conform to local electrical safety standards and use power adapters that are marked with the LPS standard when installing and using this device. Otherwise, this device may be damaged.
- Use accessories delivered with this device. The voltage must meet input voltage requirements for this device.
- If this device is installed in places with unsteady voltage, ground this device to discharge high energy such as electrical surges in order to prevent the power supply from burning out.
- When this device is in use, ensure that no water or any liquid flows into the device. If water or liquid unexpectedly flows into the device, immediately power off the device and disconnect all cables (such as power cables and network cables) from this device.
- Do not focus strong light (such as lighted bulbs or sunlight) on this device. Otherwise, the service life of the image sensor may be shortened.
- If this device is installed in places where thunder and lightning frequently occur, ground the device nearby to discharge high energy such as thunder strikes in order to prevent device damage.
CAUTION
- Avoid heavy loads, intensive shakes, and soaking to prevent damages during transportation and storage.
- The warranty does not cover any device damage that is caused during secondary packaging and transportation after the original packaging is taken apart.
- Protect this device from fall-down and intensive strikes, keep the device away from magnetic field interference, and do not install the device in places with shaking surfaces or under shocks.
- Clean the device with a soft dry cloth. For stubborn dirt, dip the cloth into slight neutral cleanser, gently wipe the dirt with the cloth, and then dry the device.
- Do not jam the ventilation opening. Follow the installation instructions provided in this document when installing the device.
- Keep the device away from heat sources such as radiators, electric heaters, or other heat equipment.
- Keep the device away from moist, dusty, extremely hot or cold places, or places with strong electric radiation.
- If the device is installed outdoors, take insect- and moisture-proof measures to avoid circuit board corrosion that can affect monitoring.
- Remove the power plug if the device is idle for a long time.
- Before unpacking, check whether the fragile sticker is damaged. If the fragile sticker is damaged, contact customer services or sales personnel. The manufacturer shall not be held responsible for any artificial damage of the fragile sticker.
Special Announcement
- All complete products sold by the manufacturer are delivered along with nameplates, quick setup guide and accessories after strict inspection. The manufacturer shall not be held responsible for counterfeit products.
- The manufacturer will update this manual according to product function enhancement or changes and regularly update the software and hardware described in this manual. Update information will be added to new versions of this manual without prior notice.
- This manual may contain misprints, technology information that is not accurate enough, or product function and operation description that is slightly inconsistent with the actual product, the final interpretation of company is as a standard.
- This manual is only for reference and does not ensure that the information is totally consistent with the actual product. For consistency, see the actual product.
NOTE: For more information, please refer to website.
Open Package Examination
- Open the package, check the appearance of product for no obvious damage, and confirm the item list for table 1- 1 is consistent.
Table 1-1 Packing list
| Component | Quantity | Remark |
|---|---|---|
| SE Series Network Camera | 1 | |
| Quick Setup Guide | 1 | |
| Installation location sticker | 1 | Optional |
| Accessories package | 1 |
Device Ports
NOTE: Different devices may have different multi-head cables; Please refer to the actual product.
Table 2-1 Multi-head cable description
| ID | Core | Description | Remark |
|---|---|---|---|
| 1 | Network access port | Connect to a standard Ethernet cable. | |
| 2 | Power supply (DC 12V) | Connect to a 12V(-15%-+10% |
) direct current (DC) power supply.
|
Quick Configuration(e.g IE)
Login
- Step 1: Open the Internet Explorer, input the IP address of IP camera (default value is 192.168.0.123) in the address box, and press Enter. The login page is displayed as shown in figure 3-1.
- Step 2: Input the user name and password.
- NOTE: The default user name is admin. The default password is admin. Change the password when you log into the system for first time to ensure system security.
- You can change the system display language on the login page.
- Step 3: Click Login icon, the main page is displayed.
Modify IP address
- Choose Setting > Network> IP, the Network page is displayed.
- Input the IP address in the IP Address box and click Apply as shown in figure 3-2.
- After the IP address is set successfully, please use the new IP address to log in the Web interface.
Browsing Video
To ensure the real-time video can be played properly, user must perform the following operation when you login the web at the first time:
- Step 1: the Internet Explorer. Choose Tools > Internet options > Security > Trusted sites > Sites, in the display dialog box, click Add, as shown in figure 3-3.
- Step 2: In the Internet Explorer, choose Tool > Internet Options > Security > Customer level, and set Download unsigned ActiveX control and initialize and script ActiveX controls not marked as safe for scripting under ActiveX controls and plug-ins to Enable, as shown in figure 3-4.
- Step 3: Download and install the player control as prompted.
NOTE
- If the repair tips displayed when installing the control, please ignore the prompt, and continue the installation, the login page is displayed when the control is loaded.
- To browse a real-time video, click Live View. The Live Video page is displayed, as shown in figure 3-5.
Description
-
1. User can view the live view.
-
2. Click Setting into the setting interface, set the parameter of device.
-
3. Click Logout to exit the live view interface, user need to input password to login again.
-
4. The alarm, when the alarm action is happening, the icon will show.
-
5 and 6 to switch the stream.
-
7. Switch the aspect ratio. Double-click in the video area to enter the full-screen mode, and double-click again to exit.
-
8. Snapshot, the picture will save to local folder(Setting > Local ).
-
9. Record, click this and record the live view and save to local folder.
-
10. Click the icon to open the Image Setting. On the Image Setting page, user can set image, scene, WB, daynight, nosie reduction, enhance image.
-
To browse device information, choose ”Setting > System > Information”，the Information page is displayed, as shown in figure 3-6.
-
To set the encode parameters, choose“Setting> Video> Encode”, the “Encode” page is displayed, as shown in figure 3-7.
Set the parameters according to the page and click “apply”
- If the message “Apply sucess!” is displayed, click OK to confirm. The system saves the settings.
- If the message “Apply failed!” is displayed, you must apply for the Parameter Configure permission from an administrator.
- If a message indicating that the “bit rate invalid” is displayed, enter a new bit rate value.
To set alarm information, Choose ”Setting > Alarm > Motion Detection”，the page is displayed, as shown in figure 3-8.
Click Enable to enable the motion detection alarm.
- Event Actions: User can choose four modes to get the alarm messages.
- Area: Drag the mouse left to choose area to set many areas, double-click left button to delete areas.
- Schedule: set the time of opening alarm.
- Click to choose all day and all week.
- Drag the mouse left button to choose hours.
- Choose the hours one by one.
Choose “Setting > System >Maintenance” the “Camera Maintenance” is displayed, as shown in figure 3-8. User can reboot ,update and reset the camera.
- Click Reboot, the message”Are you sure to restart?” is displayed, then click “OK”, the device is restarted successfully five minutes later.
- Click Update to update software, choose software and confirm to update.
- Click Reset, the message “Are you sure to reset?” is displayed, then click “OK”, the device is reset to the factory settings.
CAUTION: After you click reset, all parameters will be restored to the factory settings. Use this function carefully.
NO: 101-090-0147-01
Issue: 1.1
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>