SUNELL SN-IPR80xxAPAN Bullet Network Camera User Guide

: June 9, 2024
: SUNELL

Table of Contents

SUNELL SN-IPR80xxAPAN Bullet Network Camera
Bullet Network Camera
Product Information
Product Usage Instructions
Precautions
Special Announcement
Open Package Examination
Device Installation
Quick Configuration(e.g IE)
Read User Manual Online (PDF format)
Download This Manual (PDF format)

SUNELL SN-IPR80xxAPAN Bullet Network Camera

Bullet Network Camera

Product Information

The Bullet Network Camera is an electronic surveillance device that can be installed in public places for monitoring purposes.
It is important to strictly observe the rules provided in the product manual to avoid any potential dangers or damages caused by incorrect usage.
The device requires to be installed according to the given instructions, and must be grounded in places with unsteady voltage or frequent thunder and lightning occurrences to prevent damage.
The device should be kept away from heat sources, moist or dusty places, shaking surfaces, and strong electric radiation, and must be protected from fall-down or intensive strikes.
Proper cleaning of the device should be done with a soft dry cloth, and stubborn dirt can be cleaned with a slight neutral cleanser.

Product Usage Instructions

Before using the Bullet Network Camera, it is crucial to fully understand and observe the precautions and installation requirements provided in the product manual.
If installing the device in public places, provide an eye-catching warning sign indicating electronic surveillance is in use.
When installing the device, strictly conform to local electrical safety standards and use power adapters that are marked with the LPS standard to avoid any potential damage.
Use only the accessories delivered with the device, and ensure that the voltage meets the input voltage requirements for proper functioning.
Avoid focusing strong light on the device to prevent any damage to the image sensor.
If water or any liquid flows into the device, immediately power off the device and disconnect all cables from it.
Keep the device away from heat sources, moist or dusty places, shaking surfaces, and strong electric radiation to avoid any potential damage.
When cleaning the device, use a soft dry cloth, and for stubborn dirt, use a slight neutral cleanser, wipe gently and dry the device.
Do not jam the ventilation opening when installing the device.
If the device is idle for a long time, remove the power plug to conserve energy.

Precautions

Fully understand this document before using this device, and strictly observe rules in this document when using this device. If you install this device in public places, provide the tip “You have entered the area of electronic surveillance” in an eye-catching place. Failure to correctly use electrical products may cause fire and severe injuries.

WARNING| It alerts you to moderate dangers which, if not avoided, may cause minor or moderate injuries.
---|---
CAUTION| It alerts you to risks. Neglect of these risks may cause device damage, data loss, device performance deterioration, or unpredictable results.
NOTE| It provides additional information.

WARNING

Strictly observe installation requirements when installing the device. The manufacturer shall not be held responsible for device damage caused by users’ non-conformance to these requirements.
Strictly conform to local electrical safety standards and use power adapters that are marked with the LPS standard when installing and using this device. Otherwise, this device may be damaged.
Use accessories delivered with this device. The voltage must meet input voltage requirements for this device.
If this device is installed in places with unsteady voltage, ground this device to discharge high energy such as electrical surges in order to prevent the power supply from burning out.
When this device is in use, ensure that no water or any liquid flows into the device. If water or liquid unexpectedly flows into the device, immediately power off the device and disconnect all cables (such as power cables and network cables) from this device.
Do not focus strong light (such as lighted bulbs or sunlight) on this device. Otherwise, the service life of the image sensor may be shortened.
If this device is installed in places where thunder and lightning frequently occur, ground the device nearby to discharge high energy such as thunder strikes in order to prevent device damage.

CAUTION

Avoid heavy loads, intensive shakes, and soaking to prevent damages during transportation and storage. The warranty does not cover any device damage that is caused during secondary packaging and transportation after the original packaging is taken apart.
Protect this device from fall-down and intensive strikes, keep the device away from magnetic field interference, and do not install the device in places with shaking surfaces or under shocks.
Clean the device with a soft dry cloth. For stubborn dirt, dip the cloth into slight neutral cleanser, gently wipe the dirt with the cloth, and then dry the device.
Do not jam the ventilation opening. Follow the installation instructions provided in this document when installing the device.
Keep the device away from heat sources such as radiators, electric heaters, or other heat equipment.
Keep the device away from moist, dusty, extremely hot or cold places, or places with strong electric radiation.
If the device is installed outdoors, take insect- and moisture-proof measures to avoid circuit board corrosion that can affect monitoring.
Remove the power plug if the device is idle for a long time. Before unpacking, check whether the fragile sticker is damaged. If the fragile sticker is damaged, contact customer services or sales personnel.
The manufacturer shall not be held responsible for any artificial damage of the fragile sticker.

Special Announcement

All complete products sold by the manufacturer are delivered along with nameplates, quick setup guide and accessories after strict inspection. The manufacturer shall not be held responsible for counterfeit products.
The manufacturer will update this manual according to product function enhancement or changes and regularly update the software and hardware described in this manual. Update information will be added to new versions of this manual without prior notice.
This manual may contain misprints, technology information that is not accurate enough, or product function and operation description that is slightly inconsistent with the actual product, the final interpretation of company is as a standard.
This manual is only for reference and does not ensure that the information is totally consistent with the actual product. For consistency, see the actual product.

NOTE
For more information, please refer to website.

Open Package Examination

Open the package, check the appearance of product for no obvious damage, and confirm the item list for table 1-1 is consistent.
Table 1-1 Packing list

Component	Quantity	Remark
Bullet Network Camera	1
Quick Setup Guide	1
Installation location sticker	1
Hex Wrench	1
Swell plastic button φ5.6×29mm	3
Stainless self-tapping screw PA4.0×30mm	3
Network access port protective cover	1
Waterproof rubber seal	1
Video patch cord	1

Device Structure

Device Ports
NOTE
Different devices may have different ports and multi-head cable, please refer to the actual product.
Figure 2-1 Hardware ports

Table 2-1 Hardware ports description

ID	Port Name	Description
1	BNC Video	Sends an analog video signal. You can connect the camera to a TV

monitor through this port to view the analog video.
2| SD card slot| Install a SD card.

NOTE

Ÿ Before install a SD card, verify the card not in write protection state.

Ÿ Before remove the SD card. Verify the card not in write protection state. Otherwise, the data may be lost ,or the SD card may be damaged.

3| SD card indicator| Indicate the card status, the status is described as follows:

Ÿ Off: No card is inserted

Ÿ On: A SD card is inserted.

4| NIC indicator| When there is a network activity, the indica- tor flashes.
| Zoom lever| NOTE

Applied for MF products only.

5| Focusing lever

Table 2-2 Multi-head cable 1 description

ID	Core	Description	Remark

1

|

Network access port

| Connects to a standard Ethernet cable or PoE . The green light is on, the network connection is normal; the yellow light flashes when the data is transmitted. Some models maybe not have the lights, please refer to actual product.|

Support PoE supply.

2| Audio output| Connects to an external audio device such as a speaker.| Applied for camera with audio function

3

| Audio input port| Receives an analog audio signal from devices such as a sound pickup device.

4

|

Reset button

Table 2-3 Multi-head cable 2 description

ID	Core	Description	Remark

1

|

Network access port

| Connects to a standard Ethernet cable or PoE . The green light is on, the network connection is normal; the yellow light flashes when the data is transmitted. Some models maybe not have the lights, please refer to actual product.|

Support PoE supply.

2| Audio output| Connects to an external audio device such as a speaker.| Applied for camera with audio function

3

| Audio input port| Receives an analog audio signal from devices such as a sound pickup device.

4

|

Reset button

Camera Dimensions
NOTE
Different devices may have different dimensions, please refer to the actual product.

Device Installation

The Bullet Network Camera can be installed on the ceiling or wall. If the camera is installed on a concrete wall, install the swell plastic button before installing the bracket. If the camera is installed on a wooden wall, use self-tapping screws to install the bracket directly.
Installation Steps:

Step 1 Stick the Installation location sticker on the ceiling or wall, Drill three holes based on the marks on the sticker. Drive the swell plastic buttons into the holes.
Step 2 Connect the multi-connector cable.
NOTE
you can route cables from the top or from aside. If you use the top routing method, drill a hole in the surface first. If you use the aside routing method. When you route cables from aside, Please route the multi-head cable out from the side gap at the bottom of the camera.
Step 3 Install the camera on the ceiling or wall, and fix the screws as shown in figure 3-1.
Step 4 Loosen the fixing screw and locking ring to adjust the position so that the camera faces the monitored area, then tighten the locking ring and the fixing screw, as shown in figure 3-2.
Step 5 Unscrew the fixing screw and open the lens cover, Use the focusing lever to adjust the lens and check images on the analog monitor until the captured images are clear. Then, lock the focusing lever, screw the cover and fasten the screw(This step is applied for MF products only).

Quick Configuration(e.g IE)

Login
Step 1 Open the Internet Explorer, enter the IP address of IP camera (default value: 192.168.0.120) in the address box, and press Enter. The login page is displayed. as shown in figure 4-1 .
Step 2 Input the user name and password.

NOTE

The default user name is admin. The default password is admin.
Change the password when you log in the system for first time to ensure system security.
It is advised to restart the device three minutes later after modifying password.
You can change the system display language on the login page.

Step3 Click Login, the main page is displayed.

Modify IP address
Choose Configuration > Device > Local Network, the Local Network page is displayed.
Enter the IP address in the IP Address box and click Apply as shown in figure 4-2.
After the IP address is set successfully, please use the new IP address to log in the Web interface.

Browsing Video
To ensure the real-time video can be played properly, you must perform the following operation when you log in the web for the first time:

Step 1 the Internet Explorer. Choose Tools > Internet options > Security > Trusted sites > Sites, in the display dialog box, click Add, as shown in figure 4-3.
Step 2 In the Internet Explorer, choose Tool > Internet Options > Security > Customer level, and set Download unsigned ActiveX control and initialize and script ActiveX controls not marked as safe for scripting under ActiveX controls and plug-ins to Enable, as shown in figure 4-4.
Step 3 Download and install the player control as prompted.

NOTE
If the repair tips displayed when installing the control , please ignore the prompt, and continue the installation, the login page is displayed when the control is loaded.
To browse a real-time video, click Live Video. The Live Video page is displayed, as shown in figure 4-5.

Personnel Count: user can query the data of personnel count, through year, month, day. The statistics can be downloaded. The data can be shown by line chart, histogram, list.
AI Live video: click the icon to view the snapshots of human face or license plate (click “Face” or “Plate” to switch ). The bottom page will show the captured images of vehicle and human .

Two-way audio
NOTE
Partial camera do not support two-way audio, this section do not apply.

Camera PC
Connection：

Step 1 Connect microphone to audio input interface of camera.
Step 2 Connect speaker to the PC audio output interface.
Step 3 Login camera Web, click to turn on two-way audio.

PC Camera

Step1 Connect microphone to PC audio input interface.
Step2 Connect speaker to camera audio out interface.
Step3 Log in camera Web, click to turn on two-way audio.

Intelligent Analysis
At “Configuration > Intelligent Analysis” interface, user can set the parameters of Perimeter, Single Virtual Fence, Double Virtual Fence, Multi Loiter, Converse and Personnel Count, as shown in figure 4-7 .

Alarm Configuration
NOTE
Partial camera do not support alarm, this section do not apply.

Alarm input and Alarm output connection:

Step1 Connect alarm input device to Alarm IN0 and Alarm COM0 of multi-head cable.
Step2 Connect alarm output device to Alarm OUT1 and Alarm
COM1 of multi-head cable, alarm output interface can connect to normal open device only.
Step3 Log in Web, Choose Configuration> Alarm > Alarm..
Step4 Choose Configuration > Alarm > I/O Alarm Linkage , enable the I/O Alarm and set the parameters of Schedule Setting.

AI Multi object
At “Configuration > AI Multi object” interface, user can enable face detection, full body detection, vehicle detection, set the other parameters of detection, as shown in figure 4-8.