DEWALT DCK299P2LR Lanyard Ready Attachment Instructions

: June 9, 2024
: Dewalt

Table of Contents

References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

DCK299P2LR Lanyard Ready Attachment
Instructions

DEWALT DCK299P2LR Lanyard Ready Attachment LANYARD‑READY ATTACHMENT INSTRUCTION SHEET

WARNING: For your own safety, read the tool instruction manual before using any accessory. Failure to heed these warnings may result in personal injury and serious damage to the tool and the accessory.
WARNING: Retain this document with the tool instruction manual for future reference.
IMPORTANT: Bit clip and belt hook cannot be used with the lanyard‑ready attachment kit installed.
Safety Warnings Specific for Use At Height

Only use batteries that contain the integral battery strap. Do not use unsecured batteries while the tool is tethered. Unsecured batteries may detach from the tool if dropped.
If the tool is dropped for any reason, the lanyard attachment point 1 and battery strap components must be inspected and properly serviced prior to reuse. The lanyard attachment point is designed to stretch to absorb the shock of a drop. Any permanent stretch to the device exposing the red marked internal coils indicates it has been compromised and must be serviced prior to reuse.
Always keep the tool and accessories tethered when working “at height” [maximum lanyard length: 2m (6.5 ft.)].
Use only with lanyards appropriate for this tool type and rated for at least 5 .44 Kg (12.0 lbs).
Crush, cut or entanglement hazard. Do not use near moving parts, mechanisms or running machinery.
Do not anchor the tool lanyard to anything on your body. Anchor to a rigid structure that can withstand the forces of a dropped tool.
Make sure the lanyard is properly secure at each end prior to use.
Inspect tool and lanyard before each use for damage and proper function (including fabric and stitching). Do not use if damaged or not functioning properly.
Do not alter the lanyard attachment point or use in a manner other than as instructed in this manual.
Only attach tool to a lanyard with a locking carabiner. Do not attach by looping or knotting the lanyard. Do not use rope or cord.
Electrical shock hazard. Be sure power is off when working in high voltage areas. Some lanyards are conductive.
Dropped tools will swing on the lanyard, which could cause injury or loss of balance.
Do not carry the tool by attachment device or the lanyard.
Do not attach more than one tool to each lanyard.
Only use appropriate DeWALT brand lanyard‑ready attachment kit. NEVER modify tools to create attachment points.
Only transfer the tool between hands while properly balanced in a stable orientation.
Do not attach lanyards to tool in a way that keeps guards, switches or lock‑offs from operating properly.
Avoid getting tangled in the lanyard.
Keep lanyard away from the cutting area of the tool.
Do not use lanyards or attachment devices to get additional leverage from the tool.
Do not use for personal fall protection.
Falling object hazard! Only change accessories and attachments where a dropped object won’t cause a hazard below you. Consult your Authority Having Jurisdication (AHJ) or site supervisor for procedures for working at height.
Use multi‑action and screw gate type carabiners. Do not use single action spring clip carabiners.
The lanyard‑ready attachment kit is intended for use by competent personnel, who are trained and knowledgeable regarding working with tools in and around machinery and “at height.”

Markings
Read instruction manual before use.
Use lanyard rated for at least 5 kg.
Maximum lanyard length 2m.
Do not attach the lanyard to the battery strap. Lanyards should only be attached to the lanyard attachment point.
Components

Lanyard attachment point
Battery strap
Battery strap carabiner
Carabiner tab
Carabiner locking arm

Installing the Battery Strap Carabiner to the Lanyard Attachment Point (Fig. A–C)
WARNING: DO NOT attach the lanyard to the batterystrap. Lanyards should only be attached to the lanyard attachment point.
The carabiner 3 at the end of the battery strap 2 should be opened and then attached onto the lanyard attachment point 1 . To open the carabiner:

Install battery into tool.
Flip open the carabiner tab 4 (Fig. A).
Pull the tab outward.
Move the carabiner locking arm 5 out to open.
Attach the carabiner locking arm to the lanyard attachment point 1 (Fig. B)
Move the locking arm back into place, push the tab back down so the pin engages the locking arm.

The tool is now ready for a lanyard (Fig. C).
For more information, please contact DeWALT using the contact methods below.

Danmark
DeWALT (Stanley Black&Decker AS)
Roskildevej 22
2620 Albertslund
Tel: 70 20 15 10
Fax: 70 22 49 10
www.dewalt.dk
kundeservice.dk@sbdinc.com