SONOFF zbminil2 ZBMINI Smart Switch User Manual

ZBMINI Extreme
User manual V1.0 Zigbee Smart Switch
(No Neutral Required)

Product introduction

The device weight is less than 1kg, and the recommended installation height is less than 2m.

LED indicator status instruction

connection

ZBMINI Extreme and router connect normally, but router and the hub are disconnected

Green LED indicator slow flashes (Relay is powered on)| Abnormal network connection

Slow flashing under non-pairing state: ZBMINI Extreme and the parent device are disconnected

Features

SONOFF Zigbee smart switch (No neutral required) allows you to remote control, schedule on/off and set smart scenes to trigger other devices, etc. by connecting Zigbee hub.

Installation

1. Power off
   Please install and maintain the device by a professional electrician. To avoid electric shock hazard, do not operate any connection or contact the terminal connector whilethe device is powered on!

2. Wiring instruction
   Before installing the device, please install an air switch as the protective device (Air switch: 10A/250V).
   

For the above ③④ wiring methods, please ensure the proper wiring and powering of the L in terminal, otherwise it will cause the device to work abnormally.
Supported switches are rocker switch and push button and factory default by supporting rocker switch.
Unsupported to use with other Inductive loads such as fan.
Make sure all wires are connected correctly.

Pair with eWeLink App

1. Download the eWeLink App
   

2. Pair SONOFF Zigbee Bridge to your eWeLink account

3. Power on

After powering on, the device will enter the pairing mode defaulted during the first use and the green LED indicator will“flash slowly”.
The device will exit the pairing mode if you do not operate it within 3mins. If you want to enter the pairing mode again, press and hold the button of the device for 5 seconds until the green Led indicator “flashes slowly” and releases.
The device will remain off and cannot be controlled by the device’s button or external switch when it is in pairing mode.

4. Add ZBMINI Extreme to the ZB Bridge
   
   Open eWeLink App, tap “Add” icon on the ZB Bridge interface, then wait to looking for and add the sub-devices.

Pair with Amazon Echo

1. Download the latest Amazon Alexa App and pair it with Amazon Echo with built-in Zigbee hub.
2. Power on ZBMINI Extreme, then it defaulted to enter the pairing mode and the green LED indicator “flashes slowly”.

The device will remain off and cannot be controlled by the device’s button or external switch when it is in pairing mode.

3. Ask the Alexa Echo to discover the devices automatically by saying“Alexa, discover my devices”.
   If failed to pair within 3mins, ZBMINI Extreme will exit the pairing mode. Long press the button on ZBMINI Extreme for 5s to make it enter the pairing mode if you need to pair again.

Switch the device to the corresponding switch

The device supports rocker switch by default. If you want to change the switch type, press the button 3 times and see the green Led indicator flash 3 times quickly, then the switch type is switched successfully.
Please switch to the corresponding switch type before installing the device in the mounting box.

Install the ZBMINI Extrene in the mounting box

Specifications

LED: 150W Max @100V, 300W Max @240V
Wireless connection| Zigbee 3.0
Working temperature| -10-40°C
Casing material| PC VO
Product Size| 39.5x32x18.4mm

Factory reset

Return the device to its factory settings in any following ways (Device will enter the pairing mode automatically after resetting)

1. Press 10 consecutive times the connected external switch
2. Long-press the device for 5s.
3. Delete the sub-device on eWeLink App

Supported voice assistant

FCC Warning

Changes or modifications not expressly approved by the party responsible for compliance could avoid the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

IC Warning

This device complies with Innovation, Science and Economic Development Canada licence-exempt RSS standard (s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
ISEDC Radiation Exposure Statement:
This equipment complies with ISEDC RF radiation exposure limits set forth for an uncontrolled environment.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
Herby, Shenzhen Sonoff Technologies Co., Ltd. declares that the radio equipment type ZBMINIL2 is incompliance with Directive 2014/53/EU. The full text of the EUdeclaration of conformity is available at the following internet address:
https://sonoff.tech/usermanuals
For CE frequency
Operation frequency Range: 2405-2480MHz(Zigbee)
RF Output Power: 4.81dBm(Zigbee)

Shenzhen Sonoff Technologies Co., Ltd.
3F & 6F, Bldg A, No. 663, Bulong Rd, Shenzhen, Guangdong, China
ZIP code: 518000
Website: sonoff.tech
MADE IN CHINA

Documents / Resources

| SONOFF zbminil2 ZBMINI Smart Switch [pdf] User Manual
2APN5ZBMINIL2, zbminil2, zbminil2 ZBMINI Smart Switch, Smart Switch
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>