hama 00104952 RCR 110 Projection Alarm Clock User Manual

: June 9, 2024
: Hama

hama 00104952 RCR 110 Projection Alarm Clock

Operating instruction

Controls and Displays

Display
▼ button = decrease the current set time/ set weekday/ switch display between weekday and calendar week
▲ button = increase the current set time/ display and set time zone/ toggle 12/24-hour format
MODE button = settings / confirm a set value / switch the display mode
°C/°F/WAVE button = activate/deactivate manual radio signal reception / switch between °C and °F
button = activate/deactivate the alarm
FLIP button = turn projection 180° / switch display projection
Projection arm
CONTINUE PROJECTION sliding switch = activate/deactivate sustained projection
1DC socket
SNOOZE/LIGHT button = activate the backlight (approx. 5 seconds) / stop the alarm for 5 minutes
ROTATE control dial = manually rotate the projection up to +/–90°
FOCUS control dial = focusses the projection
Battery compartment

Display	Meaning	Display	Meaning
Radio signal	SECOND TIME	Secondary time
Weak radio signal		Alarm 1 time

PM

| 12:00-23:59
(12-hour time)| | Alarm 2 time

AM

| 0:00-11:59
(12-hour time)|

Z Z

| Snooze function

T

| Day| | Summer time

M

| Month| | Time zone-shifted time

**Explanation of Warning Symbols and Notes

**

Risk of electric shock
This symbol indicates product parts energized with a dangerous voltage of sufficient magnitude to constitute a risk of electric shock.
Warning
This symbol is used to indicate safety instructions or to draw your attention to specific hazards and risks.
Note
This symbol is used to indicate additional information or important notes.

Package Contents

• RC 110 radio-controlled alarm clock
• 2 AA batteries
• power supply unit
• These operating instructions

Safety Notes

The product is intended for private, non-commercial use only.
Protect the product from dirt, moisture and overheating, and only use it in a dry environment.
Do not use the product in areas where the use of electronic devices is not permitted.
Only connect the product to a socket that has been approved for the device. The socket must be installed close to the product and easily accessible.
Do not drop the product and do not expose it to any major shocks.
Do not attempt to service or repair the product yourself. Leave any and all service work to qualified experts.
Do not modify the product in any way. Doing so voids the warranty.
Keep the packaging material out of the reach of children due to the risk of suffocation.
Dispose of packaging material immediately according to locally applicable regulations.
Use the product for its intended purpose only.
Do not use the product in the immediate vicinity of heaters or other heat sources or in direct sunlight.
Do not operate the product outside the power limits given in the specifications.
Keep this product, as all electrical products, out of the reach of children!
Use the item only in moderate climatic conditions.
The product is intended for indoor use only.
Do not use the product in moist environments and avoid splashes.
Lay all cables so that they do not pose a tripping hazard.
Do not bend or crush the cable.
Always pull directly on the plug when disconnecting the cable, never on the cable itself

Warning – Batteries

When inserting batteries, note the correct polarity (+ and – markings) and insert the batteries Failure to do so could result in the batteries leaking or exploding.
Only use batteries (or rechargeable batteries) that match the specified
Before you insert the batteries, clean the battery contacts and the polar
Do not allow children to change batteries without
Do not mix old and new batteries or batteries of a different type or
Remove the batteries from products that are not being used for an extended period (unless these are being kept ready for an emergency).
Do not short-circuit
Do not charge
Do not throw batteries in a
Keep batteries out of the reach of
Never open, damage or swallow batteries or allow them to enter the They can contain toxic, environmentally harmful heavy metals.
Immediately remove and dispose of dead batteries from the
Avoid storing, charging or using the device in extreme temperatures and extremely low atmospheric pressure (for example, at high altitudes).

Risk of electric shock

Do not open the device or continue to operate it if it becomes
Do not use the product if the
AC adapter, the adapter cable or the mains cable are damaged.
Do not attempt to service or repair the product yourself. Leave any and all service work to qualified experts

Getting Started

Inserting the batteries

Open the battery compartment (14) and remove the contact breaker. Replace the battery compartment cover.

Replacing the batteries

Open the battery compartment (14), remove and properly dispose of the dead batteries and insert two new AA batteries with the correct polarity. Replace the battery compartment cover.

Power supply

Warning

Only operate the product from a socket that has been approved for the device. The socket must be installed close to the product and must be easily accessible.
Disconnect the product from the power supply using the On/ Off switch – if this is not available, unplug the power cord from the socket.
If using a multi-socket power strip, make sure that the total power consumption of all connected devices does not exceed the power strip’s maximum throughput rating.
If you will not be using the product for a prolonged period, disconnect it from mains power.
First connect the power supply unit to the socket (10) of the alarm clock and then to an approved mains socket.

Note

Sustained projection is only possible on mains power.
However, batteries are required even on mains power, since the other functions of the alarm clock are powered by the batteries

Installation

Note – Input

Hold down the ▲ button (3) or the ▼ button (2) to select values faster

Press the MODE button (4) repeatedly to switch between the following displays:
Temperature
Alarm mode 1 (ALM1)
Alarm mode 2 (ALM2)
Secondary time

Automatic date/time setting using the DCF signal

Once you have inserted the batteries, the display is switched on, an acoustic signal sounds and the alarm clock automatically starts searching for a DCF radio signal. During the search, the radio icon will flash.
When the wireless signal is received, the date and time are automatically set.
The search for the DCF signal takes about 7 minutes

Note – Time settings

If, during initial setup of the device, no DCF radio signal is received within the first few minutes, the search is aborted. The radio icon (6) will go out.
If there are reception problems, we recommend leaving the clock to sit overnight, since interference is generally less at night
In the meantime, you can start a manual search for the DCF radio signal at another location or you can manually set the time and date.
The clock automatically continues to search for the DCF signal every hour. If the signal is received successfully, the manually set time and date are overwritten.

Display (6)	Searching for the DCF signal

Display flashing

| Active

Display steady (not flashing)

| Successful – signal is being received

Display steady (not flashing)

| Success – weak signal reception
Not display| Inactive – no signal reception

Press and hold the °C/°F/WAVE button (5) for approx. 3 seconds to start a manual search for the DCF radio signal.

Note – Manual search

The manual search is automatically aborted after 3-5
Using the wave °C/°F/WAVE (5) frequently will drain the We recommend only using this function to seek out an optimal location for the device.

Note – Summer time

The clock automatically switches to summer time. appears on the display as long as summer time is activated.

Manually setting the date/time

Press and hold the MODE button (4) for 3 seconds until the hours display begins to flash.
Set the following information in the order listed:
- Year
- Month
- Day
- Hours
- Minutes
To select the individual values, press the ▲ button (3) or the ▼ button (2) and confirm each selection by pressing the MODE button (4).
Press the MODE button (4) immediately to adopt the set value displayed and skip ahead.
If you do not make an entry for 30 seconds, you automatically exit the setup mode.

Weekday

To change the language in which the weekday is displayed, press the ▼ button (2) for 3 seconds. The current language will be displayed.
Hold down the ▼ button (2) to change to the other languages.

Note – Day of the week

You can choose German (GE), English (EN), Italian (IT), Spanish (SP) or French (FR) for the weekday display.

Setting the time zone

Note – Time zone

The DCF signal can be received over long distances, but always transmits the current Central European Time in Make sure you account for the time difference in countries with another time zone.
If you are in Moscow, the time is 3 hours later than in This means that you should set +3 for the time zone. The clock then automatically sets the time to 3 hours after the DCF signal received or relative to the manually set time.
Press and hold the ▲ button (3) for approx. 3 seconds until the time zone symbol is displayed.
Press and hold the MODE button (4) for approx. 3 seconds to set the required time zone difference.
To select the individual values, press the ▲ button (3) or the ▼ button (2) and confirm each selection by pressing the MODE button (4).
Press and hold the ▲ button (3) for 3 seconds to switch the display between local and time zone-shifted time.

Selecting 12 or 24-hour format

Press the ▲ button (3) to switch between the 12 and 24-hour formats.

Selecting weekday/calendar week display

Press the ▼ button (2) to switch between displaying the weekday and the calendar week (WEEK).

Temperature display

Press the °C/°F/WAVE button (5) to choose between °C and °F for the temperature display.

Alarm

Note – Alarm

The alarm time always depends on the time displayed, that is, the local or time zone-shifted time ( ).

Setting the alarm time

Repeatedly press the MODE button (4) to access alarm mode 1 ( AL1 ) or 2 ( AL2 ).
Press and hold the MODE button (4) to set the alarm time for the alarm The hours display begins to flash.
Press the ▲ button (3) or the ▼ button (2) to select the hour for the alarm time and confirm your selection by pressing the MODE button (4). The minutes display begins to flash.
Repeat the process to set the minutes for the alarm time.
Press the MODE button (4) repeatedly to also set the other alarm mode or return to the temperature display.

Activating/deactivating the alarm

Press the button (9) repeatedly to activate/deactivate alarm 1 or alarm 2.
If an alarm is activated, the corresponding symbol will be displayed.

Stopping the alarm/snooze function

If the alarm is triggered, the alarm symbol will begin to flash and an alarm will sound.
Press the button (9) to stop the alarm. Otherwise, it will stop automatically after 4 minutes.

Note – Snooze function

While the alarm signal is sounding, press the LIGHT-SNOOZE button (1) to activate the snooze function. The alarm symbol (7) and ZZ will begin to flash. The alarm signal will be stopped for 4 minutes, after which it will sound again

Dual Time settings and display

Dual Time allows you to set and display a second, completely independent time (8).
Press the MODE button (4) repeatedly until SECOND TIME is displayed.
Press and hold the MODE button (4) for approximately 3 The hours display begins to flash.
Press the ▲button (3) or the ▼button (2) to select the hour and confirm your selection by pressing the MODE button (4). The minutes display begins to flash.
Repeat the process to set the minutes.
To select the individual values, press the▲ button (3) or the ▼button (2) and confirm each selection by pressing the MODE button (4).

Backlight

If you press the LIGHT-SNOOZE button (11), the display will light up for approx. 5 seconds.

Projection

Activating/deactivating

Power supply from ⇒ batteries

Press the LIGHT-SNOOZE button (11) to project the display onto the wall or ceiling for five seconds.

Power supply from ⇒ batteries + mains:

Slide the CONTINUE PROJECTION sliding switch (9) up towards to set the projection to sustained mode.
Slide the CONTINUE PROJECTION sliding switch (9) down/ away from to deactivate sustained mode.

Projection settings:

Turn the projection arm (8) forward/back to project the display onto the wall or ceiling.
Press the FLIP button (7) to rotate the projection by 180°.
Turn the ROTATE control dial (12) to further rotate the projection by up to +/–90°.
Turn the FOCUS control dial (13) to focus the projection.
Press and hold the FLIP button (7) for approx. 3 seconds to switch the projection between displaying the time and displaying the time and temperature.

Note – Projection

At a distance from the projection lens to the wall/ceiling of about 2 m / 4 m, the size of the display projection on the wall is about 10 cm / 18 cm.
By default, the projection shows the time. See the instructions above to set the projection to alternate between the time and the temperature.

Care and Maintenance

Only clean this product with a slightly damp, lint-free cloth and do not use aggressive cleaning agents. Make sure that water does notget into the product.

Note
Disconnect the device from the power supply before cleaning it or if it is not going to be used for a long period of time.

Warranty Disclaimer

Hama GmbH & Co KG assumes no liability and provides no warranty for damage resulting from improper installation/mounting, improper use of the product or from failure to observe the operating instructions and/or safety notes.

Technical Data

(EU) 2019/1782

Specifications in accordance with Regulation (EU) 2019/1782

Manufacturer’s name or trade mark, commercial registration number and address| Hama, HRA12159, Dresdner Str. 9, 86653 Monheim
---|---
Model identifier| HX06-0500300-BG
Input voltage| 100 –240 V
Input AC frequency| 50 / 60 Hz
Output voltage /
Output current /
Output power| 5.0 V DC / 0.3 A / 1.5 W
Average active efficiency| 70.7 %
Efficiency at low load (10 %)| 51.4 %
No-load power consumption| 0.06W

RCR 110 radio-controlled alarm clock

Power supply| 2 x AA batteries Power supply unit:
In: 100-240 V 50 / 60 Hz Out: 5.0 V 0.3 A
---|---
Measuring range Temperature| 0°C – +50°C/ 32°F – +122°F

Declaration of Conformity

Hereby, Hama GmbH & Co KG declares that the radio equipment type [00104952] is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: www.hama.com>00104952 ->Downloads.

Service & Support
www.hama.com
+49 9091 502-0