YETI SB140-LR Mountain Bike Frame Owner’s Manual

: June 9, 2024
: YETI

Table of Contents

SB140-LR Mountain Bike Frame
YETI SB140/LR OWNER’S MANUAL
OVERVIEW
FRAME FEATURES
MAINTENANCE
FRAME ASSEMBLY
BEARING PRESS ASSEMBLY
SWITCH INFINITY BEARING ASSEMBLY
SEAT POST SET-UP
DROPPER POST INSERTION GUIDE
EXPLODED VIEW
REBUILD KITS
FREQUENTLY ASKED QUESTIONS
LIFETIME WARRANTY
CONTACT INFORMATION
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

SB140-LR Mountain Bike Frame

YETI SB140/LR OWNER’S MANUAL

OVERVIEW

The Yeti SB140/LR is a high-performance mountain bike designed
to provide an exceptional riding experience. It comes equipped with
patented Switch Infinity technology, which delivers 140mm of rear
travel for efficient pedaling performance and a smooth ride on
rough terrain. The bike features a high modulus carbon fiber main
frame and swing arm, which provides stiffness and efficiency for
optimal performance. The frame also includes integrated ISCG-05
mounts for extra drivetrain security, rattle-free cable port
assembly for a quiet ride, and internally molded cable tubes for
hassle-free routing.

FRAME FEATURES

Switch Infinity Technology: Patented
suspension system that delivers 140mm of rear travel with efficient
pedaling performance and smooth support on rough terrain.
High Modulus Carbon Fiber Main Frame and Swing
Arm: Hand-laid carbon fiber provides stiffness and
efficiency for optimal performance.
Floating Collet Axle System: Increases bearing
life by creating a perfectly aligned connection between the front
and rear triangles of the frame.
Integrated ISCG-05 Mounts: 3-bolt ISCG-05
chain guide mounts provide extra drivetrain security for rowdy
sections.
Rattle-Free Cable Port Assembly: Clamping
cable ports ensure a quiet ride, reduced cable movement, and a
clean aesthetic. The ports are configurable for cable or wireless
components.
Internally Molded Cable Tubes: Allow for
hassle-free routing and a quiet bike by eliminating the need to
fish cables through the downtube.

MAINTENANCE

The Yeti SB140/LR requires regular maintenance to ensure optimal
performance and longevity. It is recommended that all service and
repairs be performed by your local authorized Yeti Dealer. Refer to
the Switch Infinity Service section for information on maintaining
the patented suspension system.

FRAME ASSEMBLY

The frame assembly of the Yeti SB140/LR requires proper
installation of all components to ensure optimal performance and
safety. Refer to the Bearing Press Assembly section for information
on proper installation of pivot bearings. Refer to the Dropper Post
Insertion Guide for information on proper installation of a dropper
post.

BEARING PRESS ASSEMBLY

The Bearing Press Assembly section provides information on
proper installation of pivot bearings using a bearing press tool.
It is recommended that this procedure be performed by your local
authorized Yeti Dealer.

SWITCH INFINITY BEARING ASSEMBLY

The Switch Infinity Bearing Assembly section provides
information on maintaining the patented suspension system. It is
recommended that this procedure be performed by your local
authorized Yeti Dealer.

SEAT POST SET-UP

The Seat Post Set-Up section provides information on proper
installation and adjustment of a seat post.

DROPPER POST INSERTION GUIDE

The Dropper Post Insertion Guide provides information on proper
installation of a dropper post. It is recommended that this
procedure be performed by your local authorized Yeti Dealer.

EXPLODED VIEW

The Exploded View section provides an exploded view diagram of
the Yeti SB140/LR for reference during assembly, maintenance, and
repair procedures.

REBUILD KITS

The Rebuild Kits section provides information on available
rebuild kits for the Yeti SB140/LR.

FREQUENTLY ASKED QUESTIONS

The Frequently Asked Questions section provides answers to
common questions about the Yeti SB140/LR.

LIFETIME WARRANTY

The Yeti SB140/LR comes with a lifetime warranty. Refer to the
Lifetime Warranty section for more information.

CONTACT INFORMATION

If you have any questions or concerns about your Yeti SB140/LR,
refer to the Contact Information section for contact details for
Yeti Cycles.

WARNING: Review and understand the warnings,
instructions, and content of this manual and accompanying manuals
for your bicycle. Technological advances have made bicycles and
bicycle components more complex, and the pace of innovation is
increasing. It is critical for you to have work performed by an
authorized Yeti retailer to help minimize the chances of
injury.

YETI SB140/LR OWNER’S MANUAL

TABLE OF CONTENTS

OVERVIEW

03

FRAME FEATURES

04

SB140 GEOMETRY

05

FRAME STANDARDS

07

MAINTENANCE

08

FRAME ASSEMBLY

09

BEARING PRESS ASSEMBLY

12

SWITCH INFINITY BEARING ASSEMBLY

13

SEAT POST SET-UP

15

SWITCH INFINITY SERVICE

16

DROPPER POST INSERTION GUIDE

17

EXPLODED VIEW

18

REBUILD KITS

20

FREQUENTLY ASKED QUESTIONS

22

LIFETIME WARRANTY

24

CONTACT INFORMATION

24

SB140 | OWNER’S MANUAL 2

CONGRATULATIONS ON YOUR PURCHASE OF A NEW YETI.
We are confident your new bicycle will exceed your expectations for value, performance, and ride quality. Each frameset and component has been custom specified and designed to enhance your riding experience. Whether you are a beginner cyclist, or a seasoned pro, your Yeti bicycle will provide endless hours of two-wheeled fun.
This model specific manual is designed to be used in conjunction with the general Yeti Owner’s Manual and the manuals supplied by the suspension manufacturers. If you did not receive the Yeti Owner’s Manual or the manual provided by the suspension manufacturer, download the materials off the Internet, or contact your local dealer. Bicycling can be a hazardous activity even under the best of circumstances. Proper maintenance of your bicycle is your responsibility and when done properly helps reduce the risk of injury and damage to your bicycle.
This manual outlines basic setup and maintenance recommendations of your new Yeti. It is impossible to anticipate every situation or condition that may occur during the assembly, setup, and maintenance of your bicycle, Yeti recommends that all service and repairs be performed by your local authorized Yeti Dealer.
This manual contains many “Warnings” and “Cautions” concerning the consequences of failure to maintain or inspect your bicycle. The word “Warning” indicates a potentially hazardous situation in which, if not avoided, could result in serious injury or death. The word “Caution” indicates a potentially hazardous situation in which, if not avoided may result in minor injuries or damage to your bicycle or a component of your bicycle. Be sure to read and understand all of the Warnings and Cautions listed in the manual.
WARNING: Make sure you review and understand the warnings, instructions, and content of this manual and accompanying manuals for your bicycle.
WARNING: Technological advances have made bicycles and bicycle components more complex and the pace of innovation is increasing. It is impossible for this manual or the accompanying manuals to provide all the information required to properly repair and/or maintain your bicycle. In order to help minimize the chances of an injury, it is critical for you to have work performed by an authorized Yeti retailer.

SB140 | OWNER’S MANUAL 3

THE LOWDOWN ON THE SB140/LR AND ITS FEATURES.

SB140 | OWNER’S MANUAL

FRAME FEATURES
1 SWITCH INFINITY TECHNOLOGY PATENTED SUSPENSION SYSTEM The SB140 delivers 140mm of rear travel with our patented Switch Infinity technology. Efficient pedaling performance while still smooth and supportive when the going gets rough.
2 HIGH MODULUS CARBON FIBER MAIN FRAME AND SWING ARM High modulus carbon is hand laid to create our Turq Series frames. That same stiffness and efficiency can also be found in our carbon series frame sets.
3 FLOATING COLLET AXLE SYSTEM ON PIVOTS INCREASES BEARING LIFE Floating colleted pivot axles help create a perfectly aligned connection between the front and rear triangles of the frame. Allowing the enduro max sealed bearings to keep things moving freely at the pivots.
4 INTEGRATED ISCG-05 MOUNTS 3-bolt ISCG-05 chain guide mounts are there for you in case you need extra drivetrain security for rowdy sections.
5 RATTLE-FREE CABLE PORT ASSEMBLY SECURES CABLES AND HOSES TO PROVIDE A SILENT RIDE The SB140 is designed with clamping cable ports to insure a quite ride, reduced cable movement and clean aesthetic. The ports are configurable so you can chose cable or wireless componenets without leaving behind open housing ports.

6 INTERNALLY MOLDED CABLE TUBES FOR HASSLE-FREE ROUTING AND A QUIET BIKE Gone are the days of fishing your cables through your downtube hoping they pop out the other side. The SB140’s internally molded cable tubes allow you to put the cable in one port and have it come out right where you want it.
7 INTEGRATED 41MM / 52MM TAPERED HEAD TUBE Using an integrated head tube design on the SB140 allows for a larger head tube with more area, which results in increased stiffness, and lower overall ride height without compromising any performance.
8 CUSTOM DOWN TUBE PROTECTOR AND RIBBED CHAIN GUARDS TO DECREASE CHAIN SLAP NOISE Custom seatstay, chainstay and down tube guards keep the ride quiet while protecting the frame. The nylon down tube guard keeps your bike protected where you need it most so you can focus on charging down the trail.
9 INTEGRATED AXLE AND UNIVERSAL DERAILLEUR HANGER SYSTEM Dedicated 12 x 148 boost dropouts with SRAM’s universal derailleur hanger (UDH) provide strength, stiffness and easy hanger and wheel installation.
10 CUSTOM TUNED REAR SHOCK We develop custom suspension tunes from the ground up here in Golden, CO to optimize suspension performance to perfectly compliment the SB140 suspension kinematics. For help setting up your suspension, please visit our Shock Setup Guide.
https://shocksetup.yeticycles.com/bikes

4

GEOMETRY SB140 LR

SB140 | OWNER’S MANUAL

N B
M

E

A

D

I H F
G

FIT

SMALL

5’1″ (155 CM) 5’7″ (170 CM)

MEDIUM

5’5″ (165 CM) 5’11” (180 CM)

LARGE

5’10” (178 CM) 6’3″ (191 CM)

X-LARGE

6’1″ (185 CM) 6’7″ (200 CM)

X X – L A R G E 6’5″ (195 CM) 6’11” (210 CM)

160MM FORK

SM MD LG XL XXL

A SEAT TUBE LENGTH

365

400

440

470

485

J

B E F F. T O P T U B E L E N G T H

573

603

624

652

671

C HEAD TUBE ANGLE°

65.0

650

65.0

D E F F. S E AT T U B E A N G L E °

77.0

E ACTUAL SEAT TUBE ANGLE

71.8

72.2

72.4

72.8

73.3

P

K

F CHAINSTAY LENGTH G WHEELBASE

436 1188

438 1221

440 1246

442 1277

444 1304

H ESTIMATED BB HEIGHT

342

C

I STANDOVER

726

733

737

739

744

J HEADTUBE LENGTH L
K FORK (AXLE TO CROWN)

92

95

100

112

134

575

L FORK (OFFSET)

44

O

M STACK

617

620

625

635

655

N REACH

430

460

480

505

520

O FRONT CENTER

752

783

806

835

860

P VERTICAL FORK TRAVEL

145

5

GEOMETRY SB140

SB140 | OWNER’S MANUAL

N B
M

E

A

D

I H F
G

FIT

SMALL

5’1″ (155 CM) 5’7″ (170 CM)

MEDIUM

5’5″ (165 CM) 5’11” (180 CM)

LARGE

5’10” (178 CM) 6’3″ (191 CM)

X-LARGE

6’1″ (185 CM) 6’7″ (200 CM)

X X – L A R G E 6’5″ (195 CM) 6’11” (210 CM)

150MM FORK

SM MD LG XL XXL

A SEAT TUBE LENGTH

365

400

440

470

485

J

B E F F. T O P T U B E L E N G T H

571

602

623

650

670

C HEAD TUBE ANGLE°

65.4

D E F F. S E AT T U B E A N G L E °

77.5

E ACTUAL SEAT TUBE ANGLE

72.2

72.6

72.8

73.2

73.7

P

K

F CHAINSTAY LENGTH G WHEELBASE

436 1184

438 1217

440 1242

442 1273

444 1300

H ESTIMATED BB HEIGHT

339

C

I STANDOVER

722

729

733

735

740

J HEADTUBE LENGTH L
K FORK (AXLE TO CROWN)

92

95

100

112

134

565

L FORK (OFFSET)

44

O

M STACK

614

617

621

631

651

N REACH

435

465

485

510

525

O FRONT CENTER

748

779

802

831

856

P VERTICAL FORK TRAVEL

136

6

FRAME STANDARDS

SB140 | OWNER’S MANUAL

TRAVEL WHEEL SIZE FRAME SIZE REAR SHOCK BOTTOM BRACKET REAR WHEEL SEATPOST CHAINLINE HEADSET REAR BRAKE POST MOUNT SHOCK HARDWARE MIN/MAX CHAINRING MIN MAX REAR ROTOR AXLE SPEC

140MM 29″ SM, MD, LG, XL, XXL 210MM X 55MM BSA 73MM 148MM X 12MM (BOOST) 31.6MM 55MM INTEGRATED 41MM/52MM TAPERED 180MM FRONT: M8 X 36MM REAR: CUSTOM INSERT 28T MIN/34T MAX 180MM MIN/203MM MAX 172MM M12X1

7

KEEP YOUR YETI FRESH AND CLEAN

SB140 | OWNER’S MANUAL

MAINTENANCE OVERVIEW
Following these guidelines will help maintain the performance of your bicycle and prevent more serious problems from arising. It is important to remember that service intervals can vary depending on climate, trail conditions and riding frequency. Servicing your bike requires special knowledge and tools. If you are unsure about working on your own bicycle, contact your authorized Yeti Dealer for more information on general bicycle maintenance.

TORQUE
Yeti strongly recommends using a torque wrench when assembling your frame. Torque specifications for individual parts on the SB140 are listed below, as well as in the step by step assembly instructions later in the manual. For general bicycle maintenance please consult the torque specifications of the component you are adjusting.

BEFORE EACH RIDE MONTHLY 3 MONTHS ANNUALLY

SCHEDULE
Clean and lube chain Check tire pressure Clean bike of mud and debris Check brake function Ensure all cable ends are covered with crimped cable end caps Check rims for deformations or cracks Check for loose bolts and tighten, if necessary Check headset and tighten/loosen, if necessary Check / replace brake pads Check tires for wear Check spoke tension, retention, if necessary Check chain for wear, replace if necessary Complete tune-up performed by an authorized Yeti Dealer

· · · · · ·
· ·
· · · ·
·

KEY TORQUE SPECS

ITEM # 3 0 0 0 3 0 3 61

DESCRIPTION COLLET AXLE, 15MM X 58.5L, M15X1.5

300030364

SHOULDER SCREW, 15 X 27.35L, M15 THREAD, SS PIVOT

3 0 0 0 3 0 3 76

COLLET AXLE 15MM, 43.5L

300030378

COLLET WEDGE SUB-ASSUMBLY 15MM, M4 THREADED WEDGE BOLT

300040486

COLLET WEDGE SUB-ASSEMBLY 10MM

300030057

SHCS, M6 X 1.0, 20L

300030296

COLLET AXLE M10X1.0, 30.5L X 10.5T

300030370

SCREW, MALE, M6X12.0MM

3 0 0 0 3 0174

SCREW, FH, M4 X 0.7, 16L

3 0 0 0 3 017 7

SCREW, FH, M4 X 0.7, 25L

300030357

SHCS, LOW PROFILE, M5 X 0.8, 16L

3 0 0 0 3 0173

SCREW, FH, M4 X 0.7, 10L

300060080

SRAM UNIVERSAL HANGER

100425018

REAR AXLE M12X1 X 172L BOLT-ON BLACK UDH

TORQUE (NM) 25 25 25 14 8 12 15 10 2.5 2.5 5 2.5 25 15

8

FRAME ASSEMBLY

YETI TIPS
Make sure your tools are in good condition. A worn allen key can round the hex on a bolt not allowing for proper torque.
Torque settings are listed throughout the instructions and on page 8 of this manual. It is important to prep all bolt threads. The instructions denote whether to use a Loctite compound or grease and part locations, listed in parentheses, are shown in the exploded view on page 18. Please ensure all prep call outs are followed.
WARNING: Failure to follow prep instructions could lead to serious frame issues.
WARNING: Service on Yeti bicycles requires special knowledge and tools. Yeti Cycles recommends that all service and repairs be performed by an authorized Yeti Dealer.

TOOLS NEEDED
· Torque wrench(es), 5-25 Nm, CW and CCW Directions
· 2.5mm allen key · 3mm allen key · 4mm allen key · 5mm allen key · 6mm allen key · 8mm allen key · 10mm allen key · 8mm guide pins · 3″ socket extender · Blue Loctite (243) · Grease

SB140 | OWNER’S MANUAL

01
Press Shaft Eyelet Spacer (3.22) into rear shock eyelet.

02
Install 2X Low Profile H20 Bolts (3.27) and Washers (3.28) to front triangle.
Torque: 4 Nm (or hand tight)

03
Install 2x Cable Port Clamps (3.29) to the front triangle with 2x M4 x 10L FHCS (3.33).
Install 1x Cable Port Clamp (3.29) to the rear triangle NDS Chainstay with 1x M4 x 10L FHCS (3.33).
Tighten until snug. Hardware can be torqued to 2-3 Nm after housing installation.

04
Place a Head Tube Cable Port Cover (3.32) into each recess behind the head tube.
Place a Double Port Clamp (3.30) into the nondrive side cover and a Single Port Clamp (3.31) into the drive-side cover. Secure with M4 x 25L FHCS (3.26).
Tighten until snug. Hardware can be torqued to 2-3 Nm after housing installation.

05
Install Lower DT Protector (3.36) to the front triangle using 3x Low Profile M5 Screws (3.27)
Torque: 5 Nm

06
Assemble Switch Infinity Link (3.13) into frame using 4x SHCS (3.11) with Washers (3.12). Apply Loctite to threads of (3.11). Grease zerks should face to the non-drive side. Torque in a cross pattern: 12 Nm. Repeat torque to ensure all fasteners fully tight.
9

SB140 | OWNER’S MANUAL

07
Lightly grease and place 2x Race Extenders (3.5) onto the lower bearings in Link Assembly (3.16). Install into front triangle using Link Pivot Collet Axle (3.4) and plain Collet Nut (3.2). Apply Loctite to the threads and grease the shaft of the Pivot Collet Axle (3.4). Apply grease to the Link pivot cavitites.
Torque: 25 Nm

08
Assemble Upper (3.23) and Lower (3.22) Shock Extender to SB140 Link (3.16) by placing 2X Race Extender (3.15) in the extender cavities and sliding between the Link tabs. Threaded Extender (3.23) should be oriented to the top. Secure with a Guide Pin and assemble Female 8x41mm Bolt (3.17) with Washer (3.21) through the assembly. Apply Loctite to the threads and secure with Male M6 Bolt (3.19) and Washer (3.20).
Torque: 10 Nm

09
Apply grease to main pivot cavities of Rear Triangle. Slide Rear Triangle Assembly onto main pivot and secure with Main Pivot Collet Axle (3.1) and Routing Collet Nut* (3.7), placing routing feature at the top. Apply Loctite to the threads and grease shaft of the Pivot Collet Axle (3.1).
Torque: 25 Nm
Install a plain collet nut (3.2, flat top with no clamp feature) if kit uses a wireless drivetrain.

10
Lightly grease and place 2x Race Extenders (3.5) onto the upper bearings in Link Assembly (3.16). Rotate Rear Triangle and Link together, lining up SS Pivot bores.
Apply Loctite to the threads and grease shaft and underneath the head of the SS Pivot Screws (3.3). Install 2x SS Pivot Screws (3.3) from the inside of the Link and partially into the Rear Triangle.
Apply grease to SS pivot cavities and place 2x plain Collet Nut (3.2) into the Rear Triangle.
Using a wrench from the outside of the Swingarm, begin tightening in the “left-hand” direction (this is still a standard thread, but installed from the inside), tightening the SS Pivot Screw and Collet Nut.
Torque: 25 Nm

11
Grease wedge and threads. Install Large Collet Wedge Bolts (3.9) into 2x Collet Axles (3.1) and (3.4)
Torque: 14 Nm

QC CHECK
Cycle rear triangle through to make sure motion is smooth.
Take precaution to make sure link does not contact seat tube.

10

SB140 | OWNER’S MANUAL

12
Install the Shock into the frame by securing front eyelet with a Guide Pin. Apply Loctite to the threads and grease shaft of Small Collet Axle (3.14). Install small Collet Axle (3.14) through the lower Extender (3.22), through the Shock, and thread into Upper Extender (3.23).
Torque: 15 Nm
Grease wedge and threads and install Small Collet Wedge Bolt (3.10) into Axle.
Torque: 8 Nm
Take precautions to prevent the shock striking/ contacting the downtube.

13
Install Female 8x45mm bolt (3.18) with Washer (3.21) through front Shock Eyelet and secure with M6 Male Bolt (3.19) and Washer (3.20). Apply Loctite to threads of M6 Male Bolt (3.19).
Torque: 10 Nm

14
Install Housing Clamp Cap (3.8) onto the driveside main pivot axle with a M4 x 16L FHCS (3.25).
Tighten until snug. Hardware can be torqued to 2-3 Nm after housing installation.

15
Install a Housing Clamp Cap (3.8) and Clamp Base (3.6) onto the non-drive main pivot wedge bolt with a M4 x 25L FHCS (3.26).
Tighten until snug. Hardware can be torqued to 2-3 Nm after housing installation.

16
Install Univesal Hanger (3.34) into frame. Do not use grease. Note that hanger cap bolt is reverse threaded.
Torque: 25 Nm

Check all frame bolts to ensure that no linkages are loose and there is proper fit on all components.

11

BEARING PRESS ASSEMBLY

LINK BEARING PRESS

EXTENDER BEARING PRESS

SB140 | OWNER’S MANUAL

1
3 2 1

2

1 Press both upper bearings into the link from the inside of the link tabs using a 15x24mm arbor.
Check that both bearings are fully seated.
2 Press the drive-side lower bearing into the link using a 15x24mm arbor, fully seating the bearing
into the link.
3 Install the lower bearing spacer against the pressed lower bearing. Press the non-drive side
bearing into the link until bearing bottoms against the spacer

1 Press the bearing into the upper extender with the extended race facing out of the bore.
Press into the extender until fully seated.
2 Press the bearing into the lower extender with the extended race facing out of the bore.
Press into the extender until fully seated.

12

SWITCH INFINITY V2 BEARING ASSEMBLY

BEARING REMOVAL

BEARING INSTALL

SB140 | OWNER’S MANUAL

DRIVE SIDE BEARING

3 2 1
1 Remove dust caps on the outside of the bearings. 2 Remove non-drive side bearing. 3 Remove axle sleeve from drive side bearing. 4 Remove drive side bearing.

1 4

2 33 4
1 Press drive side bearing into Switch Infinity body. 2 Slide axle sleeve into drive side bearing. 3 Press non-drive side bearing onto sleeve. 4 Replace bearing caps.

4 1

13

SWITCH INFINITY V1 BEARING ASSEMBLY

BEARING REMOVAL

BEARING INSTALL

DRIVE SIDE BEARING

1

SB140 | OWNER’S MANUAL
DRIVE SIDE BEARING
2

2
1 Remove drive side bearing and axle sleeve 2 Remove non-drive side bearing

1
1 Press non-drive side bearing into switch infinity housing (ensure extended race is facing outward
from switch infinity body).
2 Place axle sleeve in body and press drive side bearing into housing

14

SEAT POST SET-UP
STANDARD ROUTING SET-UP

SB140 | OWNER’S MANUAL

01
With a 3mm allen wrench, remove the outer plastic downtube protector.

02
Install your seatpost housing into the drive-side head tube port, pushing until it exits near the downtube cable port access hole.

03
The hole under the downtube protector provides an access point to use your finger to help push the housing around the bend in the frame up into the seat tube.

04
While pushing the housing into the head tube port, continue guiding the cable up the seat tube through the access hole until the housing exits the seat tube.

15

SWITCH INFINITY SERVICE

SB140 | OWNER’S MANUAL

01
With a 2.5mm allen wrench, remove the two clamps securing the shifter and brake housing to the main pivot.

02
With a 5mm allen wrench, remove the main pivot Collet Wedge Bolt (3.9).

03
With a 10mm allen wrench, remove the Main Pivot Collet Axle (3.1).

04
Rotate your swingarm upwards to expose the Switch Infinity Link and access both grease zerks. With a clean rag and mild detergent, clean any mud, dust, or debris off the Switch Infinity Link.

05
Remove the two dust caps from the Switch Infinity Link. Clean any debris or dust off the dust caps and bearing races in the Switch Infinity Link. Reinstall dust caps when finished.

06
Using a needle-type grease gun, push new grease into the two Switch Infinity grease ports until you see fresh grease extruding from the shaft seals. Wipe off any excess grease that was pushed out of the seals.

09
Re-install the housing clamps at the main pivot. Place a single clamp onto the shifter housing and secure with a M4 x 16L screw. Place a clamp and clamp base around the brake housing and secure with a M4 x 25L screw. Tighten until snug.

07
Apply assembly grease to the Main Pivot Collet Axle (3.1) shaft and head and apply anti-seize to the threads. Lower the swing arm and re-install your Main Pivot Collet Axle (3.1). Torque: 25 Nm.

08
Apply assembly grease to the Main Pivot Collet Wedge head and threads. Install into the Main Pivot Collet Axle (3.1). Torque: 14 Nm.

EXPLODED VIEW
A Clamps B Collet Wedge Bolt (3.9) C Main Pivot Collet Axle (3.1) D Main Pivot Collet Wedge
A

C B

A D

16

DROPPER POST INSERTION GUIDE

SB140 | OWNER’S MANUAL

Droppers are an essential tool for the modern mountain bike but proper clearance checks are required before heading out for your first ride.
The key checks are as follows:
Ensure your dropper is short enough to fit into the seat tube without interfering with the frames structure but you are still able to achieve your desired BB-Saddle measurement. See the max insertion depth chart to confirm this distance for wired and wireless posts.
There are some scenarios where you can fit a longer dropper in your frame but when you drop your dropper the saddle or battery for AXS posts could interfere with your tire during a suspension compression. See the Min BB-Saddle at full drop to confirm this distance.
Always perform a final check to ensure your post is installed to at least the minimum insertion line. Also, compress the dropper and suspension, let the air out of your shock, to ensure there is no tire interference to the saddle or AXS battery at full bottom out.
We strive to spec out dropper lengths to provide the maximum drop for the highest percentage of our riders. There is a wide range of saddle heights for every frame size. There is a possibility saddle height could fall outside of this range. A small percentage of customers might find they require a shorter or longer post given their saddle height.
Please ensure you check the minimum dimensions in the below tables before going for your first ride. Failure to do so could result in tire to saddle rub or tire to battery contact for AXS posts.
Please confirm both of these measurements, they are both required to ensure proper dropper fitment.
If you have any questions, please contact Yeti or your local bike shop.

MINIMUM BB TO SADDLE CABLED DROPPER (MM)*

X-SMALL

498.5**

SMALL
MEDIUM FRAME SIZE
LARGE
X-LARGE

497.4 496.5 No min No min

XX-LARGE

No min

*These measurements are only for cabled droppers. Please make sure if you have a wireless post you confirm that there is not any interference of the tire hitting the battery when the post is fully dropped and the suspension is fully compressed.
**If you go lower then listed minimum you run the risk of tire to saddle interference.

MAX INSERTION WIRELESS DROPPER (MM)*

X-SMALL

232.2

SMALL
MEDIUM FRAME SIZE
LARGE

242.8 277.4 316.8

X-LARGE XX-LARGE

331.0 331.0

*Subtract 34mm for a cabled dropper to accommodate housing bend angle.
17

H

H
EXPLODED VIEW
G G

F 3.15

F

3.2

3.5

3.19 E

3.20

3.16

E 3.5

3.26

D

3.8

3.6 D
3.9
3.1

3.29

C

3.33

C

3.40

B

3.34 B

3.22

3.29

3.2

EXTRA PARTS SUPPLIED

3.31

EXTR3.A38ITEMS

SUPPLIED

IN

WITH KIT

FRA3M.3E4

3.37

3.39

3.23

4 3.24

3.14
3.5 3.3
3.2

3.36 3.33.726 3.22

3.30 3.32

3.15 3.13

3.16
3.31 3.20

3.2 3.24
4 3.26

ITEM
1 1.1
SB140 | OWNER1′.S2 MANUAL

3.28

1.3 2 2.1 2.2

2.3

3.30

3

3.1

3.2 3.3 3.24

3.4

3.5

3.6 3.29
3.7

3.8

1.1

3.9

3.19

3.10

3.33.20

3.14

3.35

3.39.5 3.2

3.24

3.21

3.17

3.8 3.9
3.4

3.5

3.19

3.2

3.20

3.9 3.33

3.21

3.17

3.2 3.1

3.4 3.31 3.27

3.19 3.21
3.27

3.2 3.18 1 3.28

3.21

3.18

3.25

3.26

3.35

3.10
3.11 3.12 3.13 3.14 3.15 3.16 3.16.1 3.16.2 3.16.3 3.17 3.18

3.38

3.6 3.33

3.27

3.29

3.31 3.7
3.8 3.25

3.7 3.8

3.27 3.36

3.273.23

3.29

2.1

3.33

3.12

3.27 3.31 3.11
3.10

3.25

3.19 3.20 3.21 3.22 3.22.1 3.22.2 3.23 3.23.1 3.23.2 3.24 3.25
3.26 3.27

3.28

3.132.32

3.13

3.11

PREP KEY

GREASE

LOCTITE

3.29 3.30 3.31
3.32 NYLON P3.A33TCH
3.34

PREP KEY
NYLON

3.35

3.36

3.37

18

3.38

3.39

STOCK
3000 2000
2000 2000
3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 2000 3000 3000 2000 3000 HNA000 0000 3000 3000 3000 3000 3000 3000 2000 3000 3000 2000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 2000 3000 3000 3000

EXPLODED VIEW PARTS LIST

SB140 | OWNER’S MANUAL

ITEM # PART #

DESCRIPTION

1

SB140 FRONT TRIANGLE ASSEMBLY

1.1

SB140 FRONT TRIANGLE ASSEMBLY

2

SB140 SWINGARM ASSEMBLY

2.1

SB140 SWINGARM

2.2

Upper CS/SS Protector, 140

2.3

Lower CS Protector, Shared

3 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 3.10 3.11 3.12 3.13 3.14 3.15 3.16 3.16.1 3.16.2 3.14.3 3.17

300030361 300030362 300030364 300030376 300030365 300030366 300030367 300030368
300030378
300040486 300030057 300030214 200020422 300030296 300030375 200020385 300040539 HNA00000BA0 0000000000 300030369 300030372

SB140 SMALL PARTS ASSEMBLY COLLET AXLE, 15MM X 58.5L, M15X1.5 COLLET NUT, M15, 9.5 THICK, ROUND CAP SHOULDER SCREW, 15 X 27.35L, M15 THREAD, SS PIVOT COLLET AXLE 15MM, 43.5L RACE EXTENDER, 25 X 15.1 X 3.35 CLAMP BASE, 23MM X 3.5T, BRAKE HOUSING COLLET NUT, M15 X 1.5, SHIFTER HOSE CLAMP CLAMP CAP, HOUSING COLLET WEDGE SUB-ASSEMBLY 15MM, M4 THREADED WEDGE BOLT COLLET WEDGE SUB- ASSEMBLY 10MM SHCS, M6 X 1.0, 20L WASHER 6.3 X10.0 X 1.0 MM ASSY, SWITCH INFINITY, MECHANISM, FACTORY SERIES COLLET AXLE M10X1.0, 30.5L X 10.5T SHOCK EXTENDER BEARING EXTENSION SB140 LINK ASSEMBLY SB140 LINK
BEARING, 3802-2RS, 15 X 24 X 7
SPACER, 15.2 X 17 X 7.3L BOLT, FEMALE, 8 X 41.0, M6 THREAD

TORQUE (NM)

QTY

1 1

1 1 1 1

1

25

1

4

25

2

25

1

4

1

2

14

2

8

1

12

4

1

15

1

2

1

4

1 1

3.18 3.19 3.20 3.21 3.22 3.22.1 3.22.2 3.23 3.23.1 3.23.2 3.24 3.25 3.26 3.27 3.28 3.29 3.30 3.31 3.32 3.33 3.34 3.35 3.36 3.37 3.38 3.39 3.40

300030371 300030370 300030062 300030069 200020323 300040503 300020032 200020322 300040502 300020032 300030374 300030174 300030177 300030357 300030358 300040518 300040522 300040521 300040524 300030173 300060080 300060078 200020418 300040523 300040542 300040510 100425018

BOLT, FEMALE, 8 X 45.0, M6 THREAD SCREW, MALE, M6X12.0MM WASHER 6.5 X 12.5 X 0.5 MM WASHER 8.5 X 12.5 X 0.5 MM ASSY, SHOCK EXTENDER_60MM, BOTTOM SHOCK EXTENDER BOTTOM [60MM] BEARING, 398 MAX DBL, 8 X 19 X 10/11 ASSY, SHOCK EXTENDER_60MM, TOP SHOCK EXTENDER TOP [60MM] BEARING, 398 MAX DBL, 8 X 19 X 10/11 SHOCK EYELET SPACER SCREW, FH, M4 X 0.7, 16L SCREW, FH, M4 X 0.7, 25L SHCS, LOW PROFILE, M5 X 0.8, 16L WASHER 5.2 X 8.8 X 1.0 MM, STAINLESS ED BLACK COVER-CABLE PORT, SINGLE, RIGHT EXIT CLAMP, HT PORT DOUBLE, PA6 CLAMP, HT PORT SINGLE, PA6 CABLE PORT COVER, HEAD TUBE, 2 PIECE SCREW, FH, M4 X 0.7, 10L SRAM UNIVERSAL HANGER ASSY, YETI SEAT CLAMP, BOLT ON, 31.6 DT GUARD, MY23 OUTER, PA/ABS COVER, HT PORT, BLIND, PA6 COVER-CABLE PORT, BLANK, RIGHT EXIT FRAME PLUG, CABLE PORT REAR AXLE M12X1 X 172L BOLT-ON BLACK UDH

4

SB140 SHOCK SUB ASSEMBLY

1

10

2

1

2.5

1

2.5

3

5

3

2

3

1

2

2.5

3

25

1

2

15

1

19

REBUILD KITS

PART #

DESCRIPTION

200020435
HNA00000BA0 0000000000
300030369 300020032

LINK AND SHOCK EXTENDER BEARING REBUILD KIT BEARING, 3802-2RS, 15 X 24 X 7 SPACER, 15.2 X 17 X 7.3L BEARING, 398 MAX DBL, 8 X 19 X 10/11

200020445 300020060 300030383

SWITCH INIFINITY V2 BEARING REBUILD KIT BEARING MR17287 LLU MAX BO SWITCH INFINITY V2 BEARING SPACER

200020436 300030177 300040518 300040522 300040521 300040524 300030173 300040523 300040542 300040510 300030366 300030368 300030367 300030174

CABLE PORT KIT SCREW, FH, M4 X 0.7, 25L COVER-CABLE PORT, SINGLE, RIGHT EXIT CLAMP, HT PORT DOUBLE, PA6 CLAMP, HT PORT SINGLE, PA6 CABLE PORT COVER, HEAD TUBE, 2 PIECE SCREW, FH, M4 X 0.7, 10L COVER, HT PORT, BLIND, PA6 COVER-CABLE PORT, BLANK, RIGHT EXIT FRAME PLUG, CABLE PORT CLAMP BASE, 23MM X 3.5T, BRAKE HOUSING CLAMP CAP, HOUSING COLLET NUT, M15 X 1.5, SHIFTER HOSE CLAMP SCREW, FH, M4 X 0.7, 16L

QTY
4 1 2
2 1
3 3 1 2 2 3 1 1 2 1 2 1 1

200020437 200020418 300030357
200020438 200020406 200020405 200020419
200020421 300040543 300020032

NYLON DOWNTUBE PROTECTOR DT GUARD, MY23 OUTER, PA6 SHCS, LOW PROFILE, M5 X 0.8, 16L
SB140 PROTECTOR KIT CS/SS PROTECTOR, SB140 CS PROTECTOR, LOWER DT GUARD, MY23 INNER, TPR
SHOCK EXTENDER KIT SHOCK EXTENDER, SB140, 25MM BEARING, 398 MAX DBL, 8 X 19 X 10/11

SB140 | OWNER’S MANUAL
1 3
1 1 1
1 2

20

2 0 0 0 2 0 4 41 300030361 300030362 300030364 300030376 300030365 300030366 300030367 300030368 300030378 300030057 300030214 300030375 300030369 300030377 300030372 300030371 300030370 300030062 300030069 300030374 300030174 300030177 300030357 300030358 300040518 300040522 300040521 300040524 300030173 300040523 300040542 300040510

HARDWARE REBUILD KIT COLLET AXLE, 15MM X 58.5L, M15X1.5 COLLET NUT, M15, 9.5 THICK, ROUND CAP SHOULDER SCREW, 15 X 27.35L, M15 THREAD, SS PIVOT COLLET AXLE 15MM, 43.5L RACE EXTENDER, 25 X 15.1 X 3.35 CLAMP BASE, 23MM X 3.5T, BRAKE HOUSING COLLET NUT, M15 X 1.5, SHIFTER HOSE CLAMP CLAMP CAP, HOUSING COLLET WEDGE SUB-ASSEMBLY 15MM, M4 THREADED WEDGE BOLT SHCS, M6 X 1.0, 20L WASHER 6.3 X10.0 X 1.0 MM SHOCK EXTENDER BEARING EXTENSION SPACER, 15.2 X 17 X 7.3L SHOULDER SCREW, M10 X 23L, SHOCK EYELET BOLT, FEMALE, 8 X 41.0, M6 THREAD BOLT, FEMALE, 8 X 45.0, M6 THREAD SCREW, MALE, M6X12.0MM WASHER 6.5 X 12.5 X 0.5 MM WASHER 8.5 X 12.5 X 0.5 MM SHOCK EYELET SPACER SCREW, FH, M4 X 0.7, 16L SCREW, FH, M4 X 0.7, 25L SHCS, LOW PROFILE, M5 X 0.8, 16L WASHER 5.2 X 8.8 X 1.0 MM, STAINLESS ED BLACK COVER-CABLE PORT, SINGLE, RIGHT EXIT CLAMP, HT PORT DOUBLE, PA6 CLAMP, HT PORT SINGLE, PA6 CABLE PORT COVER, HEAD TUBE, 2 PIECE SCREW, FH, M4 X 0.7, 10L COVER, HT PORT, BLIND, PA6 COVER-CABLE PORT, BLANK, RIGHT EXIT FRAME PLUG, CABLE PORT

200020443

AXS CONVERSION KIT

1

300040510

FRAME PLUG, CABLE PORT

4

300040521

CLAMP, HT PORT SINGLE, PA6

2

300030177

SCREW, FH, M4 X 0.7, 25L

1

300030362

COLLET NUT, M15, 9.5 THICK, ROUND CAP

4

300030358

WASHER 5.2 X 8.8 X 1.0 MM, STAINLESS

1

300030173

SCREW, FH, M4 X 0.7, 10L

1

2

200020444

FOX LINEAR BEARING V2 KIT

2

200020422

FOX LINEAR BEARING V2 FACTORY

4

300030057

SHCS, M6 X 1.0, 20L

4

300030214

WASHER 6.3 X10.0 X 1.0 MM

2

1

FRAME PROTECTOR SHEET

1

400100229

GLOSS

1

400100230

M AT T E

1

2

200020354

FRAME PLUG CABLE PORT KIT

2

1

400100202

SHUTTLE GUARD

1

3

100425018

REAR AXLE M12X1 X 172L BOLT-ON BLACK UDH

5

2

3

300060080

SRAM UNIVERSAL DERAILLEUR HANGER

1

2

300030374

SHOCK EYELET SPACER

3

1

2

SB140 | OWNER’S MANUAL 2 1 1 1 1 1 1 4 4
21

FREQUENTLY ASKED QUESTIONS (1 OF 2)

SB140 | OWNER’S MANUAL

WHAT IS THE DIFFERENCE BETWEEN THE TURQ AND CARBON SERIES SB140? TURQ Series bikes are manufactured with the highest quality and best-performing carbon fiber available and offer the perfect balance of stiffness, durability, and compliance. The result is a bike that feels smooth, solid and aggressive. Carbon series bikes use a modified carbon fiber layup of our TURQ Series bikes. By using different materials and tweaking the fiber layup, we are able to make a more aggressively priced carbon high-performance mountain bike while maintaining the strength and stiffness of its higher end sibling. The carbon series SB140 weighs a bit more, about 220g for a frame.
WHAT IS SWITCH INFINITY TECHNOLOGY AND HOW DOES IT WORK? Switch Infinity utilizes a patented translating pivot that automatically switches direction as the bike moves through its travel. This provides excellent anti-squat characteristics for superior pedaling performance and ideal suspension characteristics as it gets deeper into the travel. Inside are a pair of greased bushings that slide up and down on two Kashima coated rails it’s not an extra shock that needs to be filled with air. Just keep it greased and wiped clean per our maintenance recommendations below.
DOES THE SWITCH INFINITY SYSTEM REQUIRE MAINTENANCE? The fully sealed Switch Infinity mechanism has external grease ports to lube the bushings and seals. Yeti and development partner Fox Racing Shox recommend a lubrication interval of 40 hrs of riding. It is important not to over lube the system and adhere to the recommended interval. It also doesn’t hurt to wipe off any excess dust and dirt that may accumulate throughout the week. Any maintenance supplies you need can be found on our webstore or at your local dealer.
For detailed maintenance information, please visit https://www.ridefox.com/fox17/help.php?m=bike&id=465
CAN I REPLACE OR MODIFY ANY YETI FRAME PARTS ON MY SB140? All replacement frame parts for your SB140 can be found through your local dealer or on our webstore. Only genuine Yeti parts should be used when replacing any parts on your frame. We know there are a lot of aftermarket products out there that seem legit but we do not have the ability to qualify and ensure all of these products are safe to use on our frames. If it is found that any frame part has been modified or replaced all warranties will be voided and all liability will be assumed by the customer.
CAN I CHANGE OR UPGRADE THE SPEC COMPONENTS ON MY SB140? There are many options in aftermarket parts to upgrade or personalize your bike. Some parts are standardized, especially from the big brands like Fox, Shimano, SRAM etc. You should always confirm with a professional mechanic that your parts are the correct standard and correctly and securely mount to your bike without any interference or play. Pay special attention to all the bikes standards and check the fit before use

CAN I USE AN ANGLESET ON THE SB140? The SB140 was designed with an integrated headset which has the headset cups molded into the frame so you can easily drop the bearings into the cups. There are some aftermarket anglesets available for this style headset however the frame was not tested for the use of these and therefore should not be used. Yeti’s warranty will be voided if it is found an angleset was installed on the frame and all liability will be assumed by the customer. See “What travel fork is the SB140 designed to use” for more information.
WHAT TRAVEL FORK IS THE SB140 DESIGNED TO USE? The SB140 is designed to run a 150mm or 160mm travel fork. We tested this frame to 20mm over the spec fork. So if you’re feeling the need to beef up the fork you can run up to a 180mm fork no problem. Bottom line – max axle to crown measurement of 595mm. Increasing your fork travel will slacken the head angle and seat tube angle and raise the bottom bracket. Running a shorter fork is fine too if that suits you. Shortening the fork will steepen the head angle and seat tube angle and lower the bottom bracket For more geometry information, check out the geometry section.
HOW BIG OF A TIRE CAN I FIT ON THE SB140? The short answer is the SB140 can accept up to a 2.6″ tire. There is great tire clearance on the SB140 but tire sizes vary widely by manufacturers, so it is hard to give a number that works for all brands.
CAN I FIT A WATER BOTTLE INSIDE THE FRONT TRIANGLE? Yes, we designed the SB140 to accommodate a standard sized water bottle inside the front triangle of sizes L-XXL with a piggy-back shock. Size SM and MD frames will fit a standard 21oz water bottle with a piggy-back shock. We recommend using a side-entry cage for easiest access.
WHAT CRANKS AND BOTTOM BRACKET CAN I USE ON THE SB140? The SB140 bottom- bracket standard is BSA 73mm and only wide “q” factor cranks are compatible. It is readily compatible with Shimano, SRAM, and RaceFace cranks, but a fit check is required for other brands.
WHAT REAR WHEEL AXLE FITS ON MY SB140? The SB140 is designed to work exclusively with SRAM’s Universal Derailleur Hanger at 12x148mm spacing. This axle has a thread pitch 12×1.0 and a length of 172mm. Note that this axle is only compatible with frames specifically designed with the Universal Derailleur Hanger.
WHAT TYPE OF HEADSET DOES THE SB140 USE? The SB140 uses an Integrated 41mm/52mm tapered headset. This system allows for the headset bearings to be contained inside the head tube for an overall lower ride height, more simplified installation, and increased stiffness.
22

FREQUENTLY ASKED QUESTIONS (2 OF 2)

SB140 | OWNER’S MANUAL

HOW BIG OF A ROTOR WILL FIT ON THE FRAME? The SB140 has a direct mount rear brake tab and can run a 180mm rotor without the need for a brake adaptor. With the use of a brake adaptor the frame can accept up to a 203mm rotor.
CAN I RUN A STEALTH SEATPOST DROPPER ON THE SB140? Yes. The SB140 has routing options for stealth only.
WHAT CHAINLINE WAS THE SB140 DESIGNED AROUND? The SB140 was designed around a 55mm Boost chainline. Depending on the crank and chain ring configuration you can run other chainlines but you will have to do a clearance check first.
WHAT IS THE MAX SIZE SINGLE-CHAINRING THAT FITS ON THE SB140? Without getting too technical, the max chainring size depends on the crank chainline and the chainring shape.
· Shimano / SRAM 55mm chainline Boost cranks: 34t round / 32t oval · Minimum Chainring Size: 28t round / 30t oval
Confused? Ask your local dealer or call us 303.278.6909.
DOES THE SB140 HAVE ISCG MOUNTS? Yes. The SB140 has integrated ISCG ’05 mounts. It is designed to work best with low-profile modern guides; depending on the brand, some older models with larger upper guides may not fit. We always recommend performing a fit-check with a specific chainguide to confirm compatibility.
WHAT TYPE OF SHOCK DOES THE SB140 USE? The SB140 uses a 210 x 55mm shock. Depending on the shock model, it can be locked out but we recommend running it fully open for the best compliance and traction.
WHAT TYPE OF SHOCK HARDWARE DOES THE SB140 USE? The SB140 uses M8x36mm hardware on the air can side and a custom Yeti reducer on the shaft side. If you swap between shocks, the reducer can be found here, https://yeticycles.com/gear/ detail/shock-eyelet-spacer
CAN I PUT A COIL SHOCK ON MY SB140? Yes, the SB140 is designed to be compatible with both air and coil-sprung shocks.

WHAT PERCENTAGE SAG DO YOU RECOMMEND FOR THE SB140? We would advise starting with 30% sag, or 16.5mm of shock stroke for optimal pedaling efficiency and terrain compliance. Be sure to set your sag at your normal riding weight, gear included. Feel free to venture slightly above or below 30% to suit your personal preference.
Visit our shock set up page to help set up your suspension, https://shocksetup.yeticycles.com/calculator
WHAT SIZE SEAT POST DOES THE SB140 USE? The SB140 uses a 31.6mm seat post.
WHAT SIZE SEAT COLLAR DOES THE SB140 USE? The SB140 uses a 36.4mm seat collar.
WHAT IS THE WARRANTY ON MY SB140? The SB140 has a LIFETIME manufacturer’s warranty.
WHAT IS THE LONGEST TRAVEL DROPPER POST I CAN RUN ON THE SB140? This is mostly defined by your inseam. You can run any travel as long as you are above the minimum insert mark and you are not so low your tire rubs on your saddle or your dropper bottoms out in the frame. Your local Yeti dealer can help you sort this out. We run 150mm drop on SM frames, 175mm drop on MD frames and a 200mm drop on LG-XXL.
CAN I CONVERT THIS BIKE INTO A “MULLET” BIKE AND PUT A 27.5″ WHEEL ON REAR OF THE SB140? It is possible, but we would not suggest it as it would lower your BB too much and slacken your head tube angle and seat tube angle. But hey, if those changes suit your ride style then go for it.

23

LIFETIME WARRANTY
HERE’S EVERYTHING YOU NEED TO KNOW ABOUT OUR LIFETIME WARRANTY:
All 2019 (or newer) frames, including the Switch Infinity, are covered for life against damage due to manufacturing defects for the original purchaser. Paint and finish are covered for 1-year. We will repair or replace, at our discretion, any frame we deem defective. There are a few conditions: you must register it online at yeticycles.com and you must take it to an authorized Yeti Cycles dealer for processing. Warranty does not cover damage due to ordinary wear and tear, neglect or intentional destruction. From a slingshot or your truck.
If you happen to have a crash or non-warranty situation, we’ll get you back on the trail with a reasonable replacement price. Same conditions as above.
Lifetime Warranty applies to all 2019 and newer frames (including the SB100). Model year 2018 and older frames will be covered under our previous warranty (5-year or 2-year based on time of purchase).
Simple as that. No fine print.
DISCLAIMER
Yeti Cycles is not responsible for any damages to you or others arising from riding, transporting or other use of your bicycle. In the event that your frame breaks or malfunctions, Yeti Cycles shall have no liability or obligation beyond the repair or replacement of your frame pursuant to the terms outlined in the warranty.
*If you have a warranty concern, please contact your authorized Yeti Cycles dealer.

YETI CYCLES
621 Corporate Circle, Unit B Golden, CO 80401 (p) 303-278-6909 (f) 303-278-6906 yeticycles.com

BUSINESS HOURS
Monday-Friday 8AM-11:30AM (MST) 1:00PM-5:30PM (MST)

SB140 | OWNER’S MANUAL 24