PLT SOLUTIONS PLTS-40064 Selectable LED Under Cabinet Light Fixture Instruction Manual

: June 9, 2024
: PLT SOLUTIONS

Table of Contents

SAFETY AND INSTALLATION INSTRUCTIONS
Installation Instructions
Wiring Diagram
Read User Manual Online (PDF format)
Download This Manual (PDF format)

PLTS-40064 Selectable LED Under Cabinet Light Fixture
Instruction Manual PLT SOLUTIONS PLTS-40064 Selectable LED Under Cabinet
Light Fixture Selectable LED Under Cabinet Fixture

SAFETY AND INSTALLATION INSTRUCTIONS

⚠ WARNING

Before installing, servicing, or performing routine maintenance upon this equipment, follow these general precautions.
To reduce the risk of death, personal injury, or property damage from fire, electric shock, falling parts, cuts/abrasions, and other hazards, read all warnings and instructions included with and on the fixture box and all fixture labels.
Proper grounding is required to ensure safety.
Power must be turned off at the breaker before installation or maintenance.
This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
Wear gloves and eye protection at all times while installing, servicing, or performing maintenance on the luminaire, and avoid direct eye exposure to the light source while it is on.
Do not install damaged product. Inspect luminaire for damage that may have occurred during transit. If damaged, contact the manufacturer immediately.
These instructions do not purport to cover all details or variations in equipment nor to provide every possible contingency to meet in connection with installation, operation, or maintenance. Should further information be desired or should particular problems arise which are not covered sufficiently for the purchaser’s or owner’s purposes, contact the manufacturer.

CAUTION

Install this product in accordance with country, regional and local laws and regulations.
If unsure about the installation or maintenance of this product, consult a qualified electrician and check the local electrical code.
To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
Do not make or alter any open holes in the enclosure.
Verify the supply voltage is correct by comparing it with the luminaire label.
All wiring connections should be capped with UL approved wire connectors.
Avoid direct eye exposure to the light source while it is on.
Account for small parts and destroy packing material, as these may be hazardous to children.
Risk of burn. Disconnect power and allow fixture to cool before changing/handing fixture.

NOTICE

A green ground screw is provided in the proper location. Do not relocate.
Use minimum 90° supply conductors.
Specifications and dimensions are subject to change without notice.
Suitable for dry or damp locations.

Installation Instructions

Wall Mount — No Junction Box

Carefully take the product from the box. Remove the round knock-out in the luminaire housing that is nearest the location of incoming power wires.
Remove the lens and the LED driver cover from the luminaire.
Position the luminaire housing to the desired location. Mark and drill mounting holes at the narrow ends of the keyhole slots. Screw in the mounting screws, leaving space for the channel body.
Slide the channel over the mounting screws. Lift and shift the channel into position and tighten the screws.
Make connections from the incoming power wires to the driver input power wires.
Re-attach the LED driver cover to the luminaire housing, and press the cover back until it is retained by the slots.
Re-attach the lens onto the luminaire housing.
Power on the luminaire.

PLT SOLUTIONS PLTS-40064 Selectable LED Under Cabinet Light Fixture - fig
1 Wall Mount — Junction Box

Carefully take the product from the box. Remove the center knock-out from the back of the luminaire.
Remove the lens and the LED driver cover from the luminaire.
Position the luminaire housing in the desired location. Mark and drill mounting holes at the narrow ends of the keyhole slots. Screw in the mounting screws, leaving space for the channel body.
Slide the channel over the mounting screws. Lift and shift the channel into position and tighten the screws.
Make connections from the incoming power wires to the driver input power wires. Position the junction box mounting holes on the luminaire over the junction box and secure.
Re-attach the LED driver cover to the luminaire housing, and press the cover back until it is retained by the slots.
Re-attach the lens onto the luminaire housing.
Power on the luminaire.

PLT SOLUTIONS PLTS-40064 Selectable LED Under Cabinet Light Fixture - fig
2