beam V3BU Smart Controller Installation Guide
- June 9, 2024
- BEAM
Table of Contents
beam V3BU Smart Controller
Introduction
Installation requires no special tools
Model V3BU
www.beamlabs.io 1(888) 323-9782
- Share unlimited access with friends and family.
- Explore integrations with Amazon Alexa, Google Assistant, IFTTT and the Apple Watch.
- Register your Smart Controller:
www.beamlabs.io/warranty or scan the QR code here:
TIPS:
- Setup on homeowner’s smartphone.
- Need WiFi home network ID and password with you during set-up.
Install the beam Smart Controller
- Verify that your garage door opener is connected to power.
- Plug the
**A**Smart Controller into the**B**beam smart port, look for the beam logo on your garage door opener. Make sure the Smart Controller is fully inserted and flush with the garage door opener.
Download the beam Home app & begin setup
While inside your garage download the “beam Home” app from the App Store (iOS) or Play Store (Android).
- Open the app, and select “Setup your beam”.
- Create an account and choose your V3 device.
- Follow the directions on the beam Home app to set-up your Smart Controller with your phone
NOTE: beam only connects to2.4GHznetworks.
For troubleshooting and integration setup tips go to
www.beamlabs.io or
call 1(888) 323-9782 for Technical Service.
Warning:
Toreducethe risk of injury to persons:
- Use this Smart Control only with Residential Sectional Garage doors.
- Do not enable this device on a one-piece or swinging garage door.
FCC Statement
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that m ay cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Cl ass B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy a nd, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Important Note:
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter
Beam Labs LLC
1761 International Pkwy, Ste 113
Richardson,TX75081
www.beamlabs.io
Thank you for purchasing the beam Smart Controller!
Amazon, Alexa and all related logos are trademarks of Amazon.com, Inc. or its
affiliates.
Apple is a trademark of Apple Inc., registered in the U.S. and other countries
and regions. App store is a service mark of Apple, Inc.
Google Play and the Google Play logo are trademarks of Google Inc.
©2022,Beam Labs LLC.
References
- Amazon.com
- beam labs — beamUP Smart Garage Door Openers & Accessories
- beam labs — beamUP Smart Garage Door Openers & Accessories
- beam labs — Warranty Registration
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>